HOSE, NONMETALLIC

HOSE,NONMETALLIC
HOSE, NONMETALLIC
2 IN. ID, BULK LENGTH
PER MILITARY SPECIFICATION TITLED "HOSE<(>,<)>
SYNTHETIC RUBBER, SYNTHETIC FIBER REINFORCED<(>,<)>
FOR FLEXIBLE HOSE ASSEMBLIES, (HIGH PRESSURE
SIZES -4 THROUGH -32)".
HOSE SHALL BE PACKAGED FOR SHIPMENT SO IT DOES
NOT EXCEED THE MINIMUM BEND RADIUS IN TABLE II
.
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
.
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
.
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
.
"THIS NSN CONTAINS ONE OR MORE COMPONENTS WHICH
MUST CONFORM TO SOURCE CONTROL DRAWING. BY
SUBMITTING AN OFFER, THE OFFEROR AGREES TO
PROVIDE SOURCE CONTROLLED COMPONENTS FROM
SOURCES APPROVED ON THE APPLICABLE SOURCE
CONTROL DRAWING."
.
MERCURY OR MERCURY CONTAINING COMPOUNDS SHALL
NOT BE INTENTIONALLY ADDED TO<(>,<)> OR COME IN DIRECT
CONTACT WITH<(>,<)> ANY HARDWARE OR SUPPLIES FURNISHED
UNDER THIS CONTRACT. EXCEPTION: FUNCTIONAL MERCURY
USED IN BATTERIES, FLUORESCENT LIGHTS, REQUIRED
INSTRUMENTS; SENSORS OR CONTROLS; WEAPON SYSTEMS;
AND CHEMICAL ANALYSIS REAGENTS SPECIFIED BY NAVSEA.
PORTABLE FLUORESCENT LAMPS AND PORTABLE INSTRUMENTS
CONTAINING MERCURY SHALL BE SHOCK PROOF AND CONTAIN
A SECOND BOUNDARY OF CONTAINMENT OF THE MERCURY OR
MERCURY COMPOUND. (IAW NAVSEA 5100-003D).
.
THIS NSN IS LISTED AS A PRIMARY QPL OR QML
THEREFORE THE QUALIFIED PRODUCTS LIST OR
QUALIFIED MANUFACTURERS LIST IS APPLICABLE.
.
.
4.6.1: DELETE AND SUBSTITUTE:
.
"4.6.1 PROOF PRESSURE. THE PROOF PRESSURE TEST
OF THE HOSE SHALL BE CONDUCTED IN ACCORDANCE
WITH ASTM D 380 EXCEPT THAT THE SAMPLES SHALL
BE IN ACCORDANCE WITH 4.3.1 AND 4.4.1 AND THE
PRESSURE SHALL BE INCREASED AT THE FOLLOWING
RATES:
SPE7M2-27-U-0016
SECTION B
.
(A) FOR HOSES -32 AND SMALLER, THE RATE OF
PRESSURE INCREASE SHALL BE NOT LESS THAN
15,000 PSI NOR GREATER THAN 25,000 PSI PER
MINUTE.
.
(B) HOSES GREATER THAN -32 SIZE THE PRESSURE
INCREASE SHALL NOT EXCEED 1000 PSI PER MINUTE
.
THE PRESSURE RISE SHALL BE AT A UNIFORM RATE.
THE PROOF PRESSURE SHALL BE 200 PERCENT OF THE
MAXIMUM WORKING PRESSURE SPECIFIED IN THE
APPLICABLE SPECIFICATION SHEET, AND SHALL BE
HELD FOR NOT LESS THAN 1 MINUTE NOR MORE THAN
5 MINUTES. HOSES WHICH PASS DURING THIS TEST
ARE ACCEPTABLE FOR USE. EVIDENCE OF LEAKAGE,
RUPTURE, OR DEFORMATION OF THE HOSE SHALL
CONSTITUTE FAILURE OF THIS TEST."
.
4.6.6 DELETE AND SUBSTITUTE:
.
"4.6.6 BURST PRESSURE. THE BURST PRESSURE TEST
OF THE HOSE SHALL BE CONDUCTED IN ACCORDANCE
WITH ASTM D 380 EXCEPT THAT THE SAMPLES SHALL
BE IN ACCORDANCE WITH 4.3.1 AND 4.4.1. THE
PRESSURE SHALL BE INCREASED AT A UNIFORM RATE
AS FOLLOWS:
.
(A) FOR HOSES -32 AND SMALLER THE RATE OF
PRESSURE RISE SHALL BE NOT LESS THAN 15,000
PSI NOR MORE THAN 25,000 PSI PER MINUTE.
.
(B) FOR HOSES GREATER THAN -32 THE RATE OF
PRESSURE RISE SHALL NOT EXCEED 1000 PSI PER
MINUTE.
.
THE BURST PRESSURE SHALL BE 400 PERCENT OF THE
MAXIMUM WORKING PRESSURE SPECIFIED IN THE
APPLICABLE SPECIFICATION SHEET. EVIDENCE OF
LEAKAGE, RUPTURE, OR DEFORMATION OF THE HOSE AT
OR BELOW TEST PRESSURE SHALL CONSTITITE FAILURE
OF THIS TEST. HOSES USED FOR THE BURST PRESSURE
TEST SHALL NOT BE ACCEPTABLE FOR FURTHER USE."
.
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
.
RS030: Shelf-life requirement RS001 for a TYPE I (CODE W) item with a shelf life of 120 months (non-extendable) applies to this item.
CRITICAL APPLICATION ITEM
TDP Rev A Gen 1 IAW BASIC SPEC NR MIL-DTL-24136C(1) NOT 1 REVISION NR C DTD 07/22/2025 PART PIECE NUMBER: M24136/2-32
SPE7M2-27-U-0016
SECTION B
TDP Rev A Gen 1 IAW REFERENCE SPEC NR MIL-DTL-24136/2B NOT 1 REVISION NR B DTD 07/23/2025 PART PIECE NUMBER: M24136/2-32
LINE ITEM 0000000001 TYPE OF COVERAGE: DLA DIRECT, CONUS
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 1000248629 0001 FT 157.000
This is an estimated quantity and may not be purchased by the IDC.
NSN/MATERIAL:4720001674725
DELIVERY (IN DAYS):0105
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 10% MINUS 10%
INSPECTION POINT: DESTINATION
ACCEPTANCE POINT: DESTINATION
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E QUP:001 PRES MTHD:AE CLNG/DRY:1 PRESV MAT:00 WRAP MAT:00 CUSH/DUNN MAT:00 CUSH/DUNN THKNESS:0 UNIT CONT:BV OPI:M PACK CODE:U MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129. SPECIAL MARKING CODE:32 -32 Type I, shelf life
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION,
PACKAGING, PACKING AND MARKING.
MIMNIMUM INSIDE BENDING RADIOUS IS 25.00 INCHES.

SPE7M2-27-U-0016 NSN/Part Number: 4720-00-167-4725 Quantity: 157 FT Purchase Request: 1000248629QTY: 157 Delivery: 105 days ADO