Top

58 -- RACK ASSEMBLY/INSTALLATION KIT

Active

HQ002863338605Federal

Contract Overview

Solicitation details, issuing organization, response deadlines, documents, and interested companies for this government contract opportunity.

AI Contract Overview

The contract involves a sole source procurement with Gamlet Inc. for specialized rack assembly and installation kits to support the Naval Media Center in Norfolk, VA. The procurement falls under the authority of FAR 6.302-1, allowing an exception to full and open competition because only Gamlet Inc. can satisfy the agency's specific requirements. The items to be supplied include 2 main 4-bay rack installation kits, 2 auxiliary 2-bay rack installation kits, as well as 2 units each of two different vertical rack assemblies. The main and auxiliary kits consist of various welded angle weldments, sway braces, vibration isolators, stabilizers, and stainless steel hardware kits designed for precise installation of equipment racks. The rack assemblies are constructed from 14-gauge steel with provisions for shock and vibration equipment mounting. They feature welded and ground construction, plated rack rails, removable rear panel doors, installed rack fans, solid louvered top panels, end side panels, bull nose shelves, and bottom mounting frames, all finished with black enamel paint. The 4-bay racks measure 75.13 inches high by 24 inches wide by 24 inches deep, while the 2-bay racks are slightly smaller at 61.13 inches high by 24 inches wide by 30 inches deep. This procurement was posted in January 2007 through the Department of Defense’s Dma Riverside office, with Contracting Officer Susan Madrid as the point of contact. The notice clarifies that this is not a request for competitive proposals but invites interested parties to submit comments by email.

General Info

Sole source contract with Gamlet Inc. for specialized rack assemblies supporting Naval Media Center.

Agency

Department Of Defense → Dma Riverside

NAICS

332322 - Sheet Metal Work Manufacturing

Place of Performance

Set-Aside

NONE

Documents

No documents available

Documents will appear here when they are available.

AI Contract Breakdown

Uniform Contract Format

No documents to break down

The breakdown needs solicitation documents. None were found from this contract's source.

Timeline

PostedJan 8

special-notice

Ready to pursue this opportunity?

Get full access to track this contract, build proposals with AI assistance, and manage your pipeline.

Organization & Contact Information

AgencyDepartment Of Defense → Dma Riverside

Contacts1 person available

OfficeRIVERSIDE, CA, 92518, USA

Organization / AgencyDepartment Of Defense → Dma Riverside

Office AddressRIVERSIDE, CA, 92518, USA

Contacts

Susan M. MadridContracting Officer

contact@example.gov

+1 (555) 000-0000

Full Description

This is a notice of intent to issue an order to Gamlet Inc., 190 Carlisle Ave., York PA 17401, on a sole source basis under the authority of FAR 6.302-1, Only One Responsible Source and No Other Supplies or Services Will Satisfy Agency Requirements, 10 U.S.C. 2304(c)(1). The proposed procurement is for the following rack assembly equipment listed below, in support of the Naval Media Center, Norfolk VA. This notice is not a request for competitive proposal. Interested parties may submit comments via e-mail to the Contracting Officer, Susan Madrid, e-mail: contact@example.gov. NOTE 22 applies. 2 EACH: NOMENCLATURE: RACK INSTALLATION KIT PART NUMBER: S501-MAIN-4BAY-INSTL DESCRIPTION: MAIN 4-BAY; SITE 501; C/O: 1EA 96-IN X 24-IN ANGLE WELDMENT FOUNDATION DRILLED FOR 4-BAY SITE 501 RACK (S501-MAIN-4BAY-FNDTN), 1EA 96-IN ANGLE WELDMENT SWAY BRACE FOR 4-BAY SITE 501 RACK (S501-MAIN-4BAY-SWBRC), 4EA ANGLE SUPPORT FOR MOUNTING SWAY BRACE ARM (S501- MAIN-4BAY-SWARM), 10EA VIBRATION ISOLATORS FOR FOUNDATION (2040551-8), 5EA STABILIZERS FOR SWAY BRACE (2040551-9) AND 1EA STAINLESS STEEL HARDWARE KIT (S501-MAIN-4BAY-HWKIT). 2 EACH: NOMENCLATURE: RACK INSTALLATION KIT PART NUMBER: S501-AUX-2BAY-INSTL DESCRIPTION: AUXILIARY 2-BAY; SITE 501; C/O: 1EA 48-IN X 29-IN ANGLE WELDMENT FOUNDATION DRILLED FOR 2-BAY SITE 501 RACK (S501-AUX-2BAY-FNDTN), 1EA 48-IN ANGLE WELDMENT SWAY BRACE DRILLED FOR 2-BAY SITE 501 RACK (S501-AUX- 2BAY-SWBRC), 2EA ANGLE SUPPORT FOR MOUNTING SWAY BRACE ARM (S501-AUX-2BAY-SWARM), 6EA VIBRATION ISOLATORS FOR FOUNDATION (2040551-8), 3EA VIBRATION STABILIZERS FOR SWAY BRACE (2040551-9), 1EA STAINLESS STEEL HARDWARE KIT FOR MOUNTING RACK TO INSTALLATION KIT (S501-AUX-2BAY-HWKIT). 2 EACH: NOMENCLATURE: RACK ASSEMBLY PART NUMBER: S501M-4BAY-40RU-KKDN DESCRIPTION: 4EA VERTICAL RACKS FABRICATED FROM 14 GAUGE STEEL W/PROVISIONS FOR SHOCK/VIBRATION EQUIPMENT MOUNTING, WELDED AND GROUND CONSTRUCTION, PLATED RACK RAILS, REAR REMOVABLE PANEL DOORS, RACK FANS INSTALLED, SOLID LOUVERED TOP PANELS, END SIDE PANELS, 2EA BULL NOSE SHELVES EACH RACK, BOTTOM MOUNTING FRAM; PAINTED BLACK ENAMEL; OVERALL DIMENSIONS: 75.13-IN H X 24-IN W X 24-IN D (BASED ON GAMLET DWG 11-70-00-00); 70-IN H X 19-IN W RACK OPENING. 2 EACH: NOMENCLATURE: RACK ASSEMBLY PART NUMBER: S501M-2BAY-32RU-KKND DESCRIPTION: 2EA VERTICAL RACKS W/PROVISIONS FOR SHOCK/VIBRATION EQUIPMENT MOUNTING, WELDED AND GROUND CONSTRUCTION, PLATED RACK RAILS, REAR REMOVABLE PANEL DOORS, RACK FANS INSTALLED, SOLID LOUVERED TOP PANELS, END SIDE PANELS, 2EA BULL NOSE SHELVES EACH RACK, BOTTOM MOUNTING FRAME; PAINTED BLACK ENAMEL; OVERALL DIMENSIONS: 61.13-IN H X 24-IN W X 30-IN D (BASED ON GAMLET DWG 112-56-00-00); RACK OPENING: 56- IN H X 19-IN W.

Similar Contracts

Same NAICS industry code