59 -- Misc Electrical component and tools

This is a combined synopsis/solicitation for commercial items prepared in accordance with the format in Federal Acquisition Regulation (FAR) Subpart 12.6, as supplemented with additional information included in this notice. This announcement constitutes the only solicitation; quotes are being requested and a separate written solicitation will not be issued. Competitive quotes are being requested under Request for Quote (RFQ) # N66001-17-Q- 6759. The NAICS code applicable to this acquisition is 5999 and the small business size standard is 500 employees . This procurement is a Total Small Business Set-Aside. Only quotes submitted by Small Business Concerns will be accepted by the Government. Any quote that is submitted by a non-Small Business Concern will not be considered for award. To be considered acceptable and eligible for award, quotes must provide all of the items and quantities listed below. The Government will not consider quotes or offers for partial items or quantities. Anticipated contract line items are as follows: Line # Minimum Specification QTY 1 HF AVA5-50 7/8" Andrew Heliax Coaxial Cable (PE Jacket material, corrugated copper outer conductor, foam PE dielectric. 50A, 7/8" nominal size) - Pre Cut Length = 290ft AVA5-50-290FT 1 Each 2 HF AVA5-50 7/8" Andrew Heliax Coaxial Cable (PE Jacket material, corrugated copper outer conductor, foam PE dielectric. 50A, 7/8" nominal size) - Pre Cut Length = 330ft AVA5-50-330FT 1 Each 3 HF AVA5-50 7/8" Andrew Heliax Coaxial Cable (PE Jacket material, corrugated copper outer conductor, foam PE dielectric. 50A, 7/8" nominal size) - Pre Cut Length = 320ft AVA5-50-320FT 1 Each 4 HF AVA5-50 7/8" Andrew Heliax Coaxial Cable (PE Jacket material, corrugated copper outer conductor, foam PE dielectric. 50A, 7/8" nominal size) - Pre Cut Length = 382ft AVA5-50-382FT 1 Each 5 HF AVA5-50 7/8" Andrew Heliax Coaxial Cable (PE Jacket material, corrugated copper outer conductor, foam PE dielectric. 50A, 7/8" nominal size) - Pre Cut Length = 121ft AVA5-50-121FT 1 Each 6 HF AVA5-50 7/8" Andrew Heliax Coaxial Cable (PE Jacket material, corrugated copper outer conductor, foam PE dielectric. 50A, 7/8" nominal size) - Pre Cut Length = 87ft AVA5-50-87FT 1 Each 7 VHF/UHF LDF4-50A 1/2" Andrew Heliax Coaxial Cable (PE Jacket material, corrugated copper outer conductor, foam PE dielectric. 50A, 1/2" nominal size) - Pre cut Length = 171ft. LDF4-50A-171FT 2 Each 8 VHF/UHF LDF4-50A 1/2" Andrew Heliax Coaxial Cable (PE Jacket material, corrugated copper outer conductor, foam PE dielectric. 50A, 1/2" nominal size) - Pre cut Length = 60ft. LDF4-50A-60FT 2 Each 9 VHF/UHF LDF4-50A 1/2" Andrew Heliax Coaxial Cable (PE Jacket material, corrugated copper outer conductor, foam PE dielectric. 50A, 1/2" nominal size) - Pre cut Length = 143ft. LDF4-50A-143FT 2 Each 10 Panavise Vise All-Purpose Combo Of 303 & 300 Model 301 620PO012 2 Each 11 Fluke Networks MS2-100 Cable Tester 374TE1007 3 Each 12 3/4 in. x 100 ft. Flexible Aluminum Conduit 5603-30-AFC 8 Each 13 1-1/4 in. x 50 ft. Flexible Aluminum Conduit 5605-24-00 31 Each 14 1-1/4 in. Flexible Metal Conduit (FMC) Screw-In Coupling 100184943 30 Each 15 3/4 in. Flexible Metal Conduit (FMC) Screw-In Coupling 90452 40 Each 16 1-1/4 in. Electrical Metallic Tube (EMT) 1-Hole Straps (4-Pack) 26154 10 Each 17 3/4 in. Electrical Metallic Tube (EMT) 1-Hole Conduit Straps (4-Pack) 96152 20 Each 18 5/8 in X 6 in. Strong-Bolt 2 Wedge Anchor (20 per pack) WA62600 3 Each 19 5/8 - 11 in. Stainless Steel Hex Nut (6-Pack) 43744 9 Each 20 5/8 in. Stainless Steel Flat Washer (12-Pack) 43758 9 Each 21 5/8 in. Stainless Steel Split Lock Washer (12-Pack) 43754 5 Each 22 Herco HE826 Precision Screwdriver Set 49826000001 2 Each 23 Digital Multimeter, Crenova MS8233D Auto-Ranging Digital Multimeters Electronic Measuring Instrument AC Voltage Detector Portable Amp / Ohm / Volt Test Meter Multi Tester w/ Diode and Continuity Test Scanners Home Use Electronic DIY Hand Tools with Backlight LCD Display, Orange BEM0010-3 2 Each 24 Lockheed martin Systems Inegration 6084744 Silicone Rubber Tape Self Fusing T-SR-6084744-16-S25-BK 12 Each 25 Wall Anchors One Hole Straps UPC:785592130259 OHS-300 110 Each 26 1/2IN X 2-1/2IN Hex Nut Lok-Bolt Anchor DFM121156P 110 Each 27 CABLE, COAXIAL LMR-400DB LMR-400DB 100 Each 28 N Male to N Male Low Loss 400 Coaxial Assembly - 5 FT 28-400-005 5 Each 29 N Male to N Male Low Loss 400 Coaxial Assembly - 20 FT 28-400-020 5 Each 30 N MALE TO N MALE ADAPTER 604 10 Each 31 TYPE N-MALE COAXIAL CABLE END COMPRESSION CONNECTOR FOR RG-8 UG-1185/U ARS-G304C 60 Each 32 BNC-MALE TO N-MALE COAXIAL ADAPTER CONNECTOR ARS-G051 5 Each 33 BNC-FEMALE TO N-FEMALE COAXIAL ADAPTER CONNECTOR ARS-G068 5 Each 34 TYPE N MALE/FEMALE RIGHT ANGLE ELBOWCOAXIAL ADAPTER CONNECTOR ARS-G337 10 Each 35 12-10 AWG UNINSULATED TERMINAL,1/4" STUD SIZE (20 PACK) DK000270 2 Each 36 6 AWG UNINSULATED TERMINAL,1/4" STUD SIZE (10 PACK) DK001413 2 Each 37 16 oz. Wood Handle Rubber Mallet 30503 2 Each 38 Tie-Down Stakes for 1/2 in. OD Tubing (25 pk) NFT-LS6 25 Each 39 10.oz Epoxy Dispensing Tool (Compatible with SET-XP10 Adhesive) CDT10S 3 Each 40 Masonry Drill Bit, Spline, 5/8InDia, 10In L DW5709 15 Each 41 Adapter Coaxial Connector N Jack, Female Socket To N Jack, Female Socket 50 Ohm 82-101 8 Each 42 Cement PVC Medium Gray 8 oz (pkg of 5) (UPC 038753308845) 30884 12 Each 43 Cable Cutter, 8-1/4" Overall Length, Shear Cut Cutting Action, Primary Application: Electrical Cable 63028 3 Each 44 Ratcheting Winch w/Strap, Spur, 900 lb G3978956 3 Each 45 3-Strand Polypropylene Rope - 1/4" x 600' Yellow 91401050 1 Each 46 10/32 Screw for Rack, 50 pcs Black 8621 2 Each 47 Cable Ties, 100/Pack 4.0" FT8110A 4 Each 48 Zip Ties (Outdoor, 7.3" length, 50lb strength - 100pack TY525MX 4 Each 49 Cable Ties, 100/Pack 14.5" FT8130A 4 Each 50 Husky 15inch tool bag 82035N12 2 Each 51 Dewalt Drill/Drive Bit Set (130-piece) DWA4CASE130HD 3 Each 52 Husky Screw driver set (15-Piece) 246340150 3 Each 53 Type N (f) to Type N (f) splice Coaxial Adapter Connector AXA-NFNF 20 Each 54 All Weather Foil Tape, 72mm x 46m, Silver 330X 6 Each 55 Stanley FatMax 14-563 9-7/8-Inch Straight Cut Aviation Snip 14-563 2 Each 56 CABLE MOUNT PLUG 18 PIN CONTACT, mil spec M55181/7-01 M55181/7-03 12 Each 57 3/4 in. 2-Hole Conduit Straps (10-Pack) 26122 5 Each 58 1-1/2 in. PVC Conduit Clamp (Case of 6 5-Packs) E977HC-CTN 2 Each 59 Coupling, Setscrew, EMT Steel, 2 In G2954165 100 Each 60 Model 3841 Type N (f) to Type N (f) splice 73044 35 Each 61 TEKTON, 7/8 in. Flex-Head Ratcheting Combination Wrench WRN57016 3 Each 62 1 in. 12-Point SAE Full Polish Combination Wrench HCW1 3 Each 63 SAE/Metric T-Handle Hex Key Set (14-Piece) HTHKSM14PCN 3 Each 64 General Tools Machinist Scribe 400PR090 3 Each 65 Xcelite Plier Long Nose w/cuttere Serated 5 1/2" 272PL120 3 Each 66 Reversible 66 Punch Down Bit 700-028 3 Each 67 Thread Screws and Cage Nuts HWM6-100-CAGE 6 Each 68 Thread Screws and Cage Nuts HWM1032-100-CAGE 6 Each 69 Crimp Connector, Pins, Plastic Hood, & All Hardware | Gold-Plated Contacts | Create Custom Pinout (DB25 MALE) 1154 20 Each 70 Crimp Connector, Pins, Plastic Hood, & All Hardware | Gold-Plated Contacts | Create Custom Pinout (DB25 FEMALE) 1153 20 Each 71 Crimp Connector, Pins, Plastic Hood, & All Hardware | Gold-Plated Contacts | Create Custom Pinout(DB9 MALE) 1101 20 Each 72 Crimp Connector, Pins, Plastic Hood, & All Hardware | Gold-Plated Contacts | Create Custom Pinout(DB9 FEMALE) 1100 20 Each 73 DB15 Male Crimp Connector Kit - Plastic 1116 20 Each 74 DB15 Female Crimp Connector Kit Plastic 1111 20 Each 75 20-28 AWG Wire | Hardened Steel | Cushioned Handles | Standard & HD D- Sub Pins 93-100-014 2 Each 76 20-26AWG Wire | For Insertion & Extraction | Compatible with Standard & HD D-Sub Connectors 93-100-300 20 Each 77 Circular MIL Spec Connector 19P Size 14 Straight Pin Plug PT06SE-14-19P 20 Each 78 AMPHENOL INDUSTRIAL PT06E-8-2S Circular Connector, PT Series, Straight Plug, 2 Contacts, Solder Socket, Bayonet, 8-2 PT06E8-2S 20 Each 79 The U-229/UG1 is a 5-way cable-mount Male Audio Plug with solder cup ideal for use in communications equipment where the highest reliability is required under the most severe environmental conditions. All feature easy mating using a twist-lock motion. Non-rigid, spring-loaded contacts provide a positive electrical connection with minimum voltage drop. U-229/UG1 20 Each 80 9 Conductor 24 AWG Low Smoke Zero Halogen Bulk Cable, 100 ft. roll CSLSZH09-100 1 Each 81 22AWG 6C SHIELD,Alpha Wire Multi-Conductor Cables, 100ft roll 602-5196C- 100 2 Each 82 EUROPEAN GERMANY POWER STRIP CEE7 "SCHUKO" 6 OUTLET (EU1-16R) POWER STRIP 16 AMPERE-250 VOLTS. POWER STRIP SUPPLIED WITH 3 METER ( 9FT.- 9IN) LONG POWER CORD WITH CEE 7/7 (EU1-16P) ANGLE TYPE PLUG. BLACK BASE/GRAY COVER. 52906 4 Each 83 BNC Male to N Female Adapter - Gold Plated 4124 10 Each 84 BNC-Male to N-Female Coaxial Adapter RFA-8363 10 Each 85 Deutsch - Machined Contact 26482 SERIES 1 26500 26518 PIN M39029/31- 240 60 Each 86 Tripp Lite 10U SmartRack Wall Mount Rack Enclosure Cabinet with Door & Side Panels; UPC Code: 037332154828 SRW10US 3 Each 87 Navepoint Fixed Rack Vented Server Shelf 1U 19" 4 post Rack Mount Adjustable from 14 - 23" 9SIA4FH3SG1369 6 Each 88 Wire Stripper/Cutter with Solid and Stranded Wire 11054 3 Each 89 5in Light-Weight Flush Cutter 6007 3 Each 90 10in Cable Cutter 200-069 3 Each 91 8in Cable Cutters 200-013 3 Each 92 Phone and Computer Repair and Maintenance Tool Kit (79 Piece) DT4943 3 Each 93 Electricians Tool Set (Kit includes 18-Inch heavy duty multi-pocket bag. Heavy duty, 8 pocket leather pouch. Two inch leather tool belt. Nine inch side-cutting pliers. Eight inch diagonal cutting pliers. Eight inch long nose pliers. Ten inch pump pliers. Pro plus wire stripper 10-18 AWG. NM cable ripper, stripping/crimping combination tool. Cable cutter, folding utility knife, 12 inch hacksaw, keystone tip square shank 1/4-Inch by 4-Inch. Flat blade screwdriver. Keystone tip square shank 5/16-Inch by 6-Inch. Flat blade screwdriver, cabinet tip round shank 3/16 inch by 6 inch. Flat blade screwdriver. Cabinet tip round shank 1/4 inch by 6 inch. Flat blade screwdriver, Phillips tip #1 - 3/16-Inch by 3-Inch. Screwdriver, Phillips Tip #2 - 1/4-Inch by 4-Inch. Screwdriver, screw holding screwdriver 3/16-Inch by 6- Inch. Three inch scratch awl. Ten inch adjustable wrench. Nine piece folding hex-key Set. Twenty five feet tape measure, torpedo level, 18 ounce . Electrician's hammer, high dexterity gloves, size large and GT-11 voltage tester.) 0159-11 1 1 Each 94 M12 12-Volt Lithium-Ion 1/4 in. Hex Cordless Screwdriver Kit 2401-22 1 Each 95 Shockwave Impact Duty Driver Bit Set (40-Piece) 48-32-4008 1 Each 96 LiteFuze LT-2000 2000 Watt Voltage Converter Transformer - Step Up/Down - 110V/220V - Circuit Breaker Protection LT-2000 3 Each 97 Soldering Iron Stations (Analog soldering station, 120V, 50W) 2 Each 98 RF ATTENUATOR 150W 30DB WES51 8 Each 99 100db Setp Attenuator with 1db Step N Female Connnectors rated up to 3GHz and up to 2 Watts in a Dial Design SA37100n 2 Each 100 40 dB Fixed Attenuator N Male To N Female Directional Up To 3 GHz Rated To 500 Watts With Black Aluminum Heatsink Body SA3N500-40 1 Each 101 Hex bolts, Stainless steel 316, 5/8"-11 x 5" (Bulk QTY 100) 16219 1 Each 102 Hex bolts, Stainless steel 316, 5/8"-11 x 5" (Box QTY 10) 16219 1 Each 103 Hex bolts, Stainless steel 316, 3/8"-16 x 5" 16143 16 Each 104 Flat washers, Stainless steel 316, 3/8" 16021 32 Each 105 High collar lock washers, Stainless steel 316, 3/8" 20901 16 Each 106 Hex nuts, Stainless steel 316, 3/8"-16 15985 16 Each 107 DIN AUDIO/VIDIO CONN, 5 CONTACTS, JACK, PANEL MOUNT, GOLD U-183/U 5 Each 108 MIL Spec Connector 19S Size 14 Straight Pin Plug (Socket) PT07MW14-19S 4 Each 109 N-TYPE MALE CONN, AVA5-50 CABLE, ANDREW 78EZNM 15 Each 110 CABLE PREP TOOL FOR AVA5-50 CABLE N-TYPE A5FX-EZPT 3 Each 111 SOCKET PIN FOR PT07MW14-19S MS39029/32-259 76 Each 112 N-TYPE MALE CONN, LDF4RN-50A CABLE, ANDREW L4TNM-PS 15 Each Free on Board (FOB) Destination Shipping Address for Delivery and Acceptance: N66001 Ship to Address: Ship to Address: N66001 SPAWAR Systems Center Pacific Receiving Officer 4297 Pacific Highway, Bldg OT7 San Diego, CA 92110-5000 Offeror Instructions: Notice: The Government may consider quotes that fail to follow all instructions to be unacceptable and ineligible for contract award. Quotes shall: 1. Include a separate concise, clear, and descriptive narrative technical approach (not to exceed one page) on how they will provide all of the supplies to the site. Quoters are encouraged to submit pictures, brochures, or and other pertinent technical information of the quote to facilitate the evaluation; 2. Include pricing for each individual unit and a total price in US Dollars ($); 3. Be written in English and show the offeror name, address, DUNS and CAGE code, business size and type of small business, and telephone and e-mail address of an Offeror point of contact; 4. Stay within the page limitations indicated below; 5. Be submitted in electronic PDF or Excel format; and Certification: "To be considered for award, the offeror certifies that the product(s) being offered is an original, new and Trade Agreements Act (TAA) compliant product, and that the subject products are eligible for all manufacturer warranties and other ancillary services or options provided by the manufacturer. Offeror further certifies that it is authorized by the manufacturer to sell the products that are the subject of this action in the US (i.e., that the products are TAA compliant and that the offeror is authorized to sell them in the US)." Certification is not limited in pages. Offerors are required to submit documentation with the offer identifying its supply chain for the product, and certifying that all products are new, TAA compliant, and in their original packaging. By making an offer, offeror also consents to no cost cancellation of the non-compliant awarded items if, upon inspection after delivery, any products provided are not recognized or acknowledged by the manufacturer as new and original products that are eligible for warranties and all other ancillary services or options provided by the manufacturer or that offeror was not authorized by the manufacturer to sell the product in the US, or that the product is in some manner not TAA compliant. All text shall be formatted on an 8 by 11 inch page in 12 point Times New Roman font. All pages of the Technical File shall be numbered and shall not exceed ten pages. The technical acceptability shall include the following: Factor I Specifications: See technical acceptability specifications The price quote shall include the following: Factor II Price: The price quote shall include the following and is limited to one page: Offerors shall provide a unit price for each item and a total firm-fixed-price for all line items. The total firm-fixed-price shall include all applicable taxes, shipping, and handling costs to the shipping address listed above. Evaluation Factors for Award: Factor I Specifications: The Government will evaluate the quote to see if the following specification requirements are met: Basis of award: The government anticipates awarding a firm-fixed price purchase order and it will be based on the lowest priced technically acceptable. "QUOTE BRAND NAME or EQUAL SPECIFATIONS" (See attached Drawing specifications) Factor II- Price: Lowest price Technically acceptable (LPTA) The Government will evaluate the total price to determine if it is fair and reasonable. Notice: Any offer rated "Unacceptable" under any one of the above factors may be determined to be ineligible for contract award. Basis For Award: This procurement will use the lowest price technically acceptable source selection methodology. The Government intends to award a contract to the lowest price technically acceptable quote received in response to this solicitation. Any quote evaluated as unacceptable will not receive an award. This solicitation document incorporates provisions and clauses in effect through Federal Acquisition Circular (FAC) 2005-91 and Defense Federal Acquisition Regulation Supplement (DFARS) Publication Notice 20161222 . It is the responsibility of the contractor to be familiar with the applicable clauses and provisions. The clauses can be accessed in full text at www.farsite.hill.af.mil or https://acquistion.gov/far/. The following provisions apply to this acquisition : FAR 52.204-7, System for Award Management (Oct 2016); FAR 52.212-1, Instructions to Offerors Commercial Items (Jan 2017); FAR 52.212-3 and Alt I, Offeror Representations and CertificationsCommercial Items (Jan 2017); FAR 52.225-25, Prohibition on Contracting with Entities Engaging in Certain Activities or Transactions Relating to IranRepresentation and Certifications (Oct 2015); 252.203-7005, Representation Relating to Compensation of Former DoD Officials (Nov 2011); and 252.247-7022, Representation of Extent of Transportation by Sea (Aug 1992). The following clauses, incorporated by reference, apply to this acquisition: 52.204-16, Commercial and Government Entity Code Reporting (Jul 2016); 52.204-18, Commercial and Government Entity Code Maintenance (Jul 2016); 52.212-4, Contract Terms and Conditions -- Commercial Items (Jan 2017). FAR Clause 52.212-5-Contract Terms and Conditions Required to Implement Statutes or Executive Orders -- Commercial Items applies to acquisition and includes: 52.XXX-X , The following additional FAR and DFARS clauses, incorporated by reference, apply to this solicitation: 52.232-39, Unenforceability of Unauthorized Obligations (Jun 2013); 52.232-40, Providing Accelerated Payments to Small Business Subcontractors (Dec 2013); 52.233-4, Applicable Law for Breach of Contract Claim (Oct 2004); 252.203-7000, Requirements Relating to Compensation of Former DoD Officials (Sep 2011); 252.203-7002, Requirement to Inform Employees of Whistleblower Rights (Sep 2013); 252.204-7003, Control of Government Personnel Work Product (Apr 1992); 252.204-7006, Billing Instructions (Oct 2005); 252.204-7011, Alternative Line Item Structure (Sep 2011); 252.204-7012, Safeguarding of Unclassified Controlled Technical Information (Oct 2016); 252.232-7003, Electronic Submission of Payment Requests and Receiving Reports (Jun 2012); 252.232-7006, Wide Area Work Flow Payment Instructions (May 2013); 252.232-7010, Levies on Contract Payments (Dec 2006); 252.244-7000, Subcontracts for Commercial Items (Jun 2013); and, 252.247-7023, Transportation of Supplies by Sea (Apr 2014). This RFQ closes on 13 Jul 2017 at 10:00 AM, Pacific Time. Questions and quotes must be uploaded on the SPAWAR e-Commerce website at https://e- commerce.sscno.nmci.navy.mil, under SSC Pacific/Simplified Acquisitions/N66001-17-Q- 6759. E-mail quotes or offers will not be accepted. Late quotes will not be accepted. For e-Commerce technical issues, contact the SPAWAR Paperless Initiatives Help Desk at 858- 537-0644 or contact@example.gov. The point of contact for this solicitation is Frederick Espiritu at contact@example.gov. Please include RFQ# N66001-17-Q-6759 on all inquiries. The due date for questions is 11 Jul 2017. Questions may be addressed afterward at the discretion of the Government. All responding vendors must have a completed registration in the System for Award Management (SAM) website prior to award of contract. Information can be found at https://www.sam.gov/. Complete SAM registration means offerors shall have a registered DUNS and active CAGE Code. Attachments: 1. 1300646685 Item Description