SWITCH, SLIDE

SWITCH,SLIDE
SWITCH,SLIDE
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RQ002: CONFIGURATION CHANGE MANAGEMENT ENGINEERING CHANGE PROPOSAL
REQUEST FOR VARIANCE (DEVIATION OR WAIVER)
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
THIS ITEM IS IDENTIFIED AS A COMMERCIAL ITEM (TO INCLUDE 'COMMERCIAL
OF A TYPE')
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
NOTE: THIS IS A RESTRICTED SOURCE ITEM AND
REQUIRES ENGINEERING SOURCE APPROVAL BY THE
GOVERNMENT DESIGN CONTROL ACTIVITY.
ALTERNATE OFFEROR REQUIREMENTS:
THE FOLLOWING DOCUMENTATION IS REQUIRED IN
ACCORDANCE WITH MIL-T-31000. (A) ALL DRAWINGS
AND SPECIFICATIONS REQUIRED FOR MANUFACTURE.
(B) PROCESS/OPERATION SHEETS WHICH DESCRIBE
IN DETAIL EACH CRITICAL PROCESS AND ASSOCIATED
INSPECTION/ACCEPTANCE CRITERIA. (C)
IDENTIFICATION OF SOURCES WHO WILL PERFORM
CRITICAL PROCESSES/OPERATIONS, INCLUDING
SOURCES OF FORGINGS AND CASTINGS. (D) IF
AVAILABLE COPIES OF PURCHASE ORDERS FROM THE
ITEM. (E) A SHOCK EXTENSION REPORT IN
ACCORDANCE WITH MIL-S-901 AND IN A FORMAT AS
SPECIFIED IN DI-ENVR-80706 IS REQUIRED.
IF THE OEM'S DETAILED DRAWINGS ARE NOT
AVAILABLE, THE OFFEROR MUST SUPPLY AN
ENGINEERING ANALYSIS REPORT WHICH DETAILS HOW
THEIR DRAWINGS WERE DEVELOPED. ADDITIONALLY,
IF REVERSE ENGINEERING WAS USED, THE COMPLETE
SPE7M8-27-T-0636
SECTION B
PROCEDURE WILL BE REPORTED INCLUDING: NUMBER
OF SAMPLES, METHODS AND MEASURES USED, ALL DATA
COMPILED, RATIONALE FOR DIMENSION TOLERANCE
DEVIATION, AND RATIONALE FOR ACCEPTANCE. THIS
DATA WILL BE FORWARDED TO THE ENGINEERING
SUPPORT ACTIVITY FOR NSN/Part Number: 5930-01-123-6516 Quantity: 32 EA Purchase Request: 7019029017QTY: 32 Delivery: 172 days ADO