Skip to main contentPsst! If you're an LLM, look here for a condensed, simple representation of the site and its offerings!

LiveFree Webinar — Wednesday, October 28 at 2:00 PM ET

Register Free →

This Solicitation opportunity from Department Of Defense was posted on May 20, 2026. The submission period has ended. Browse the details below for market research, or find similar active opportunities.

ADAPTER ASSEMBLY, IN

Closed
SPE4A6-26-T-66H5Federal

Contract Overview

Solicitation details, issuing organization, response deadlines, documents, and interested companies for this government contract opportunity.

Active Opportunities Like This One

AI Contract Overview

Show more

The contract is for the procurement of 49 units of an ADAPTER ASSEMBLY, IN, identified by NSN 4920015166078 and part number 20000355-19, issued under solicitation SPE4A6-26-T-66H5 by the Defense Logistics Agency Aviation, ASC Commodities Division. Delivery is required within 172 days after order placement, with FOB Origin terms, and the item must be shipped to the designated receiving warehouse at 25600 S Chrisman Road, Tracy CA 95304-5000. The item must comply with comprehensive technical and quality requirements outlined in the DLA Master List of Technical and Quality Requirements, referenced by R or I numbers, and must adhere to MIL-STD-2073-1E packaging standards with specific preservation methods, materials, and unit container specifications. Marking must follow MIL-STD-129 with no special marking required, and physical identification must meet RQ017 guidelines, though Item Unique Identification is not mandated per DFARS 252.211-7003(c)(1)(i). Inspection and acceptance occur at the destination, with sampling required to follow MIL-STD-1916, ASQ H1331 Table 1, or an equivalent zero-based plan; critical, major, and minor attributes must be verified at levels VII, IV, and II or AQLs of 0.1, 1.0, and 4.0 respectively, with unspecified attributes treated as major. The manufacturer’s inspection system must meet SAE AS9003 or ISO 9001 tailored to AS9003 requirements, and tailored higher-level quality requirements apply to both manufacturers and non-manufacturers. Cybersecurity compliance requires a CMMC Level 2 self-assessment, and covered defense information provisions apply. The contractor must comply with all relevant FAR and DFARS clauses, including whistleblower protections, disclosure of information, safety issue notification, transportation by sea, and prohibition of confidentiality agreements. The contract mandates use of the WAWF system for invoicing and receiving reports, with the contractor required to maintain active SAM registration and WAWF access. Offerors must represent their small business status, certify against suspension and debarment, disclose covered defense telecommunications equipment, and adhere to Berry Amendment and Buy American Act restrictions if

General Info

Supply 49 Adapter Assemblies by July 2025 with MIL-STD packaging, inspection, and CMMC Level 2 compliance.

NAICS

332721 - Precision Turned Product Manufacturing

Place of Performance

REC WHSE 57, TRACY, CA, 95304-5000, USA

Set-Aside

NONE

Documents

1

RFQ SPE4A6-26-T-66H5 DLA Aviation May 21 2026

PDF, High priority: read this firstrfq
High

AI Contract Breakdown

Uniform Contract Format

Sign up to view the full breakdown with detailed analysis of each section.

Timeline

PhaseClosed
Posted

Combined Synopsis

Response Deadline

Deadline has passed

Submission Closed

Find active opportunities like this

Start your free trial to discover similar active contracts, track opportunities, and build proposals with AI assistance.

Organization & Contact Information

Show more
AgencyDepartment Of Defense → ASC COMMODITIES DIVISION
Contacts1 person available
OfficeUSA
Office AddressUSA

Full Description

Show more
ADAPTER ASSEMBLY,IN
ADAPTER ASSEMBLY, INTERFACE DEVICE
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RD002, COVERED DEFENSE INFORMATION APPLIES
RD004: Cybersecurity Maturity Model Certification (CMMC) Level 2 Self-Assessment RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS
(MANUFACTURERS AND NON-MANUFACTURERS)
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RQ017: PHYSICAL INDENTIFICATION/BARE ITEM MARKING
Item Unique Identification is not required by request of the Service customer. DFARS 252.211-7003(c)(1)(i) applies.
RT001: MEASURING AND TEST EQUIPMENT
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
NORTHROP GRUMMAN SYSTEMS CORPORATION 34860 P/N 20000355-19
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
SPE4A6-26-T-66H5
SECTION B
PR: 7007689144 PRLI: 0001 CONT’D
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 7007689144 0001 EA 49.000
NSN/MATERIAL:4920015166078
DELIVERY (IN DAYS):0172
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: DESTINATION
ACCEPTANCE POINT: DESTINATION
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:33 CLNG/DRY:1 PRESV MAT:49
WRAP MAT:GB CUSH/DUNN MAT:BG CUSH/DUNN THKNESS:C
UNIT CONT:E5 OPI:M
INTRMDTE CONT:E5 INTRMDTE CONT QTY:AAA
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:00 -00 No special marking
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
PARCEL POST ADDRESS:
W62G2T
W1A8 DLA DIST SAN JOAQUIN
25600 S CHRISMAN ROAD
REC WHSE 57
TRACY CA 95304-5000
US
FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE
C20 AND CONTRACT
FREIGHT SHIPPING ADDRESS:
W62G2T
W1A8 DLA DIST SAN JOAQUIN
25600 S CHRISMAN ROAD
REC WHSE 57
TRACY CA 95304-5000
US
Need Ship Date:11/13/2024 Original Required Delivery Date:07/17/2025
SPE4A6-26-T-66H5 NSN/Part Number: 4920-01-516-6078 Quantity: 49 EA Purchase Request: 7007689144QTY: 49 Delivery: 172 days ADO

More opportunities from Department Of Defense → ASC COMMODITIES DIVISION

Same awarding agency

NAICS: 332722
New
DIBBS
WASHER, LOCK
Solicitation # SPE4A6-26-T-40D5
Solicitation SPE4A6-26-T-40D5 is a fixed-price procurement issued by the Defense Logistics Agency for 91 internal and external tooth lock washers, identified by NSN 5310012533723. The required components must be manufactured from Stainless Steel CRES 302 and adhere to technical specifications FF-W-100 Type 3 Style 1 and FF-W-100C(1). Dimensional requirements are governed by MS 45904-86 or ASME B18.21.1, with specific tolerances for the inner diameter (.512 to .530 inches), outer diameter (1.380 to 1.410 inches), and thickness (.052 to .060 inches). The items are to be delivered to the DLA Distribution DDSP New Cumberland facility in Pennsylvania by November 27, 2026, with a delivery window of 202 days after order. Quality assurance and inspection will occur at the point of origin, requiring compliance with MIL-STD-1916, ASQ H1331, or MIL-STD-105/ASQ Z1.4, with a zero-nonconformance acceptance policy. Packaging must follow RP001 and ASTM D3951, while marking and labeling must comply with MIL-STD-129 and MIL-STD-130N. Item Unique Identification is not required. The contract incorporates various FAR and DFARS clauses, including the Buy American Act and safeguarding requirements for covered defense information under NIST SP 800-171. Payment processing is mandated through the Wide Area Workflow system. This is not a small business set-aside, and it falls under NAICS code 332722.
Bolt, Nut, Screw, Rivet, and Washer Manufacturing

POSTED

5 days ago

DEADLINE

in about 10 hours
View Details

Find Active Opportunities Like This

Get AI-powered intelligence on the opportunities still open

Every page of the solicitation package shredded into a compliance breakdown

AI-powered matching based on your capabilities and past performance

Competitor and incumbent history on the requirement

Automated alerts on amendments, Q&A deadlines, and award

Miguel
Hillary
Keith Deutsch
Christine

Join 750+ contractors already using CLEATUS