ADAPTER, STRAIGHT, FL

ADAPTER,STRAIGHT,FL
ADAPTER, STRAIGHT, FLANGE TO HOSE.
CRES MATERIAL, PASSIVATED. FOR USE WITH 3.5 INCH AIR DUCT HOSE. PER
DETAIL SPECIFICATION SHEET TITLED "CONNECTOR, PNEUMATIC STARTER DUCT,
FLANGE, FEMALE."
FULL AND OPEN COMPETITION APPLY
RD003, COVERED DEFENSE INFORMATION POTENTIALLY APPLIES
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
The following Contract Data Requirements Lists (CDRLs), DD Form 1423s, apply to this procurement. Review the Technical Data Package (TDP) for additional information.
RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RT001: MEASURING AND TEST EQUIPMENT
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
EXCEPTION TO THE DETAIL SPECIFICATION SHEET: MIL-S-6721 HAS BEEN
SPE4A0-26-T-4952
SECTION B
CANCELLED. AN ADDITIONAL ACCEPTABLE COMPOSITION FOR TUBE PORTION OF
ADAPTER IS 18-8 CRES (AISI 321) OR EQUAL. GOVERNMENT FAT APPLIES. PER
FAR 52.209-4: (A) THE CONTRACTOR SHALL DELIVER (2) COMPLETE UNIT(S)
WITHIN (30) CALENDAR DAYS (NOTE: THE DELIVERY SCHEDULE ON THE FACE OF
THE SOLICITATION REFLECTS ONLY THE TIME TO DELIVER THE SUPPLIES, NOT THE
FIRST ARTICLE.) FROM THE DATE OF THIS CONTRACT TO: DLA PRODUCT TEST
CENTER COLUMBUS BLDG 9 SECTION 2 COLUMBUS, OH 43218-3990 ATTN: MARK DEEM
GOVERNMENT FAT APPLIES. (B) WITHIN (30) CALENDAR DAYS AFTER THE
GOVERNMENT RECEIVES THE FIRST ARTICLE, THE CONTRACTING OFFICER SHALL
NOTIFY CONTRACTOR THAT CONTRACTOR MAY DELIVER THE APPROVED FIRST ARTICLE
AS A PART OF THE CONTRACT QUANTITY. DLAD 52.209-9016 GOVERNMENT TESTING
COST: ($1,200.00 USD) AFTER RECEIPT OF QUOTES, OFFERORS MAY BE CONTACTED
TO PRICE THE FAT REQUIREMENT. PER DLAD 52.209-9018, ALT VI DISPOSITION
OF FIRST ARTICLES: CONTRACTOR MAY DELIVER THE APPROVED FIRST ARTICLE AS
A PART OF THE CONTRACT QUANTITY.
CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE
USED NOR INCORPORATED IN ANY ITEMS TO BE
DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION
SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT
DOES NOT ALLEVIATE ANY PRODUCT REQUIREMENTS.
SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR
APPROVAL UNLESS THEY ARE AUTHORIZED BY THE
SPECIFICATION REQUIREMENTS.
A. Data required by this document will be included in the price of the procured item(s).
B. The supplier shall prepare and furnish one (1) copy of the Certificate of Quality Compliance (COQC) for all delivered supplies. If the supplies delivered under this contract are from more than one manufacturing lot, a separate one (1) copy of the COQC shall be prepared and furnished for each manufacturing lot represented by, manufactured or produced under a product specification, original equipment manufacturer (OEM)/manufacturer's part number, commercial, industry or military standard, or drawings, or other technical data. Each Certificate shall be prepared in accordance with the Supplemental Quality Assurance Provision (SQAP).
C. For contracts assigned for Government inspection at source, the supplier shall have the completed Certificate available for review by the Government representative when the material is presented for acceptance by the Government. The Government representative can sign off on the WAWF receiving report so long as the Contractor complied with the COQC and the documentation is uploaded as an attachment to the Production CLIN in iRAPT.
D. An electronic copy of each COQC, for Government records retention, shall be entered into the Invoicing, Receipt, Acceptance and Property Transfer (iRAPT) system by the supplier via the Attachment tab of the Receiving Report (RR). NSN/Part Number: 4730-00-960-4568 Quantity: 1 EA Purchase Request: 7018373639QTY: 1 Delivery: 5 days ADO