BAR, METAL

BAR,METAL
BAR<(>,<)> METAL
NICKEL ALLOY 400
HOT FINISH, ROUND
1.500 IN DIA
6 TO 24 FT LG
6.740 LB/FT (REF)
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RD003, COVERED DEFENSE INFORMATION POTENTIALLY APPLIES
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
IY010: QUALIFIED SUPPLIERS LIST FOR DISTRIBUTORS (QSLD) REQUIREMENT (DLA
TROOP SUPPORT JUNE 1994) FOR FSG'S 95 AND 96.
ONLY SUPPLIERS LISTED ON THE QSLD ARE ELIGIBLE FOR AN AWARD PURSUANT TO
THIS SOLICITATION.
SUPPLIERS NOT QUOTING IN COMPLIANCE WITH THE QSLD REQUIREMENT MUST
INDICATE THEY ARE DEVIATING FROM THE REQUIREMENTS OF THE SOLICITATION.
ANY BID/QUOTE/OFFER BASED ON A PRODUCT SUPPLIED BY OTHER THAN AN
APPROVED QSL DISTRIBUTOR, EVEN THOUGH THE PRODUCT MIGHT HAVE BEEN
MANUFACTURED IN ACCORDANCE WITH THE DRAWING(S) AND/OR SPECIFICATION(S)
AS CITED IN THE PURCHASE ORDER
TEXT (POT) IS A BID/QUOTE/OFFER WITH EXCEPTION AND MUST BE SO INDICATED
BY THE
QUOTER/OFFEROR.
ANY PRODUCT FURNISHED UNDER A CONTRACT OR ORDER FOR A PRODUCT DESIGNATED
AS PART OF THE QSL PROGRAM, UNLESS SPECIFICALLY AUTHORIZED BY THE
GOVERNMENT IN WRITING, MUST FULLY COMPLY WITH THE TERMS AND CONDITIONS
OF THE QSL PROGRAM. ANY PRODUCT, WHICH DOES NOT FULLY COMPLY WILL BE
CONSIDERED AN UNAUTHORIZED SUBSTITUTION, AND MAY YIELD CRIMINAL
PENALTIES IN ADDITION TO ANY CIVIL REMEDIES AVAILABLE TO THE GOVERNMENT.
FOR THIS SOLICITATION, AND ANY RESULTING ORDER ISSUED TO AN APPROVED
QSLM/QSLD SUPPLIER
WHOSE QUOTE IS BASED ON COMPLIANCE WITH THE QSL PROGRAM, (EXCEPT IN THE
CASE OF FMS (FOREIGN MILITARY SALE) REQUIREMENTS), REFERENCES TO SOURCE
INSPECTION ARE HEREBY WAIVED. IN SUCH CASES, COQC, PVT, QAP-EQ003, ASQ
H1331, AND RQ006: QUALITY CONFORMANCE INSPECTION REQUIREMENTS, IF
REFERENCED, DO NOT APPLY.
SPE8E4-26-T-2360
SECTION B
FOR MORE INFORMATION ABOUT THE QSL PROGRAM GO TO THE FOLLOWING WEBSITE:
https://www.dla.mil/TroopSupport/IndustrialHardware/Engineering-and-Tech nical-services/Qualified-Suppliers-List/
-ORWRITE TO: DLA TROOP SUPPORT, ATTN: DLA TROOP SUPPORT FHTF, BLDG 3/B, 700 ROBBINS AVENUE, PHILADELPHIA, PA 19111-5092
Qualification requirements in procurement note #M03 Qualified Suppliers List for Manufacturers (QSLM)/Qualified Suppliers List for Distributors (QSLD) for Troop Support# apply. The full text of procurement note M03 can be found in the DLA Directive (DLAD) of Procurement Notes on the Web at: https://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx.
(END STO)
Metal Certification Contract Data Requirements Lists (CDRLs), DD Form 1423s, apply to this procurement. Review the Technical Data Package (TDP) for additional information. If CDRL-METALSCERT is missing from DLA Technical Data Management Transformation (TDMT) they can also be viewed in the DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
A Certificate of Quality Compliance (Mill-Material Certification) is required. A copy of the Certificate of Quality Compliance shall be provided with every shipment to the customer or DLA depot, and a copy of the Certificate of Quality Compliance provided for each shipment shall be forwarded to the DLA Troop Support Contracting Officer identified on the award.
CONTINUOUS IDENTIFICATION MARKINGS ARE REQUIRED IN ADDITION TO THE
MARKING REQUIREMENTS CITED IN THE PROCUREMENT SPECIFICATION:
AS A MINIMUM, EACH UNIT OF ISSUE (FEET,PLATE, OR SHEET) SHALL BE
IDENTIFIED WITH THE (1) DLA CONTRACT DELIVERY ORDER NUMBER, (2) NSN, (3)
SPECIFICATION NUMBER AND REVISION, (4) GRADE,CLASS & TYPE, ALLOY, PART
NUMBER,DIE NUMBER, AND TEMPER, (5) MANUFACTURER'S NAME, HEAT AND LOT
NUMBER, (6) DIMENSIONS.
MATERIAL SHALL BE SUPPLIED WITHIN THE REQUIRED MIN-MAX LENGTH
REQUIREMENTS AND MUST IN WHOLE FEET LENGTH ONLY (I.E. 10, 11, OR 12 FT
EVEN)
PERMISSIBLE MARKING METHODS ARE STAMPING (EXCEPT DIE STAMP) OR
STENCILING. THE CHARACTERS SHALL BE OF SUCH A SIZE AS TO BE LEGIBLE AND
VISIBLE TO THE UNAIDED EYE. THE MARKING FLUID APPLIED SHALL NOT
CONTAMINATE, OR OTHERWISE HAVE A DETRIMENTAL EFFECT ON THE PRODUCT OR
ITS PERFORMANCE. THE MARKINGS SHALL BE WATERPROOF AND SUFFICIENTLY
STABLE TO WITHSTAND NORMAL HANDLING.
IN LIEU OF "LINE MARKINGS", ADHESIVE LABELS ARE REQUIRED FOR EACH UNIT
OF STRAIGHT BARS, TUBES AND SHAPES, UNDER 0.250 INCHES IN NOMINAL OD,
AND TO BE SECURELY FASTENED. TAGS WILL BE ACCEPTABLE METHOD FOR WIRES.
FAILURE TO COMPLY WILL BE CAUSE FOR REJECTION OF END PRODUCT."
TDP Rev A Gen 1 IAW BASIC UNK QQ-N-281D(2) NOT 1 REVISION NR D DTD 12/23/2020 PART PIECE NUMBER: CLASS A, FORM 1, HOT FINISH
TDP Rev A Gen 1 IAW REFERENCE QAP 13873 CDRL-METALSCERT-26124 REVISION NR DTD 12/04/2025
SPE8E4-26-T-2360
SECTION B
PART PIECE NUMBER:
TDP Rev A Gen 1 IAW REFERENCE STD NR MIL-STD-129R(3) REVISION NR R DTD 02/25/2023 PART PIECE NUMBER:
TDP Rev A Gen 1 IAW REFERENCE NON GOVT STD ASTM A700-14 (R 2019) REVISION NR DTD 11/01/2014 PART PIECE NUMBER:
TDP Rev A Gen 1 IAW REFERENCE NON GOVT STD SAE AMS2806 REVISION NR D DTD 12/20/2018 PART PIECE NUMBER:
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 7018364741 0001 FT 132.000
NSN/MATERIAL:9530002394464
DELIVERY (IN DAYS):0156
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 10% MINUS 10%
INSPECTION POINT: DESTINATION
ACCEPTANCE POINT: DESTINATION
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:10 CLNG/DRY:0 PRESV MAT:00
WRAP MAT:00 CUSH/DUNN MAT:00 CUSH/DUNN THKNESS:0
UNIT CONT:00 OPI:M
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
PRESERVATION ZZ = IAW ASTM A700 PACKING Z = IAW ASTM A700 MARKING IAW MIL-STD-129
SPECIAL PACKAGING CODES Z AND ZZ SHALL BE AS SPECIFIED IN ASTM A700.
MARKING Z= MARKING SPECIFICATION(S) LISTED IN CONTRACT AND ADDITIONAL
REQUIREMENTS IN THE PURCHASE ORDER TEXT(POT).
ADDITIONAL MARKING REQUIREMENTS: WHEN THE
CONTRACT OR ORDER REFLECTS TWO UNITS
SPE8E4-26-T-2360
SECTION B
PR: 7018364741 PRLI: 0001 CONT’D
(EXAMPLE: FT-LB, LB-SH, LB-CL, ETC.)
SHIPMENT MARKINGS SHALL INCLUDE THE
QUANTITY OF BOTH UNITS. THIS MARKING
DOES NOT APPLY FOR MATERIAL SHIPPED LOOSE.
PARCEL POST ADDRESS:
W25G1U
W1A8 DLA DISTRIBUTION
DDSP NEW CUMBERLAND FACILITY
2083 NORMANDY DRIVE DOOR 113 TO 134
NEW CUMBERLAND PA 17070-5002
US
FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE
C20 AND CONTRACT
FREIGHT SHIPPING ADDRESS:
W25G1U
W1A8 DLA DISTRIBUTION
DDSP NEW CUMBERLAND FACILITY
2083 NORMANDY DRIVE DOOR 113 TO 134
NEW CUMBERLAND PA 17070-5002
US
Need Ship Date:03/15/2027 Original Required Delivery Date:01/29/2027
SPE8E4-26-T-2360 NSN/Part Number: 9530-00-239-4464 Quantity: 132 FT Purchase Request: 7018364741QTY: 132 Delivery: 156 days ADO