BEARING, ROLLER, ROD

BEARING,ROLLER,ROD
BEARING,ROLLER,ROD END
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS
(MANUFACTURERS AND NON-MANUFACTURERS)
RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS
(MANUFACTURERS AND NON-MANUFACTURERS)
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
IDENTIFY TO:
BEARING RESTRICTION:
RESTRICTION ON THE ACQUISITION OF BALL AND ROLLER BEARINGS (JUN 2011)
AN AWARD FROM THIS SOLICITATION CAN ONLY BE MADE FOR A BEARING
MANUFACTURED IN THE UNITED STATES, ITS OUTLYING AREAS, OR CANADA AND FOR
EACH BALL OR ROLLER BEARING, THE COST OF THE BEARING COMPONENTS (ROLLING
ELEMENTS, RETAINER, INNER RACE, OR OUTER RACE) MANUFACTURED IN THE
UNITED STATES, ITS OUTLYING AREAS, OR CANADA MUST EXCEED 50% OF THE
TOTAL COST OF THE BEARING COMPONENTS OF THAT BALL OR ROLLER BEARING. SEE
DFARS CLAUSE 252.225-7016, RESTRICTION ON ACQUISITION OF BALL AND ROLLER
BEARINGS.
A CONTRACTOR’S DECLARATION ON THE DOMESTIC/FOREIGN NATURE OF MATERIAL
BEING OFFERED IS REQUIRED. PLEASE VISIT THE FOREIGN BEARING WEBSITE AT
https://www.dla.mil/Aviation/Business/Foreign-Bearing-Waiver/. TO OBTAIN A COPY OF THE CONTRACTOR’S DECLARATION. PLEASE PRINT, COMPLETE, SIGN AND HAVE READY FOR SUBMISSION UPON REQUEST FROM THE BUYER. FAILURE TO PROVIDE THIS INFORMATION MAY RESULT IN YOUR QUOTE NOT BEING CONSIDERD FOR AWARD.
SPE4A6-26-T-16GZ
SECTION B
IN THE EVENT NO OFFERED BEARINGS MEET THIS SOURCING REQUIREMENT, THIS
SOLICITATION MAY BE CANCELLED OR HELD PENDING A WAIVER APPROVAL
REQUESTED BY THE PROCUREMENT ACTIVITY. UPON RECEIPT OF AN APPROVED
WAIVER FROM THE DOMESTIC SOURCING RESTRICTION, THE REQUIREMENT MAY BE
RE-SOLICITED OR BUYER MAY REQUEST A QUOTE EXTENSION. SEE DFARS
225.7009-4, WAIVER, RESTRICTION ON BALL AND ROLLER BEARINGS.
SAMPLING:
RQ017: PHYSICAL INDENTIFICATION/BARE ITEM MARKING
DEERE & COMPANY 75755 P/N R55081
TDP Rev A Gen 1 IAW REFERENCE QAP 13873 QAP-B02 REVISION NR B DTD 12/11/2013 PART PIECE NUMBER:
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 7017870011 0001 EA 1,112.000
NSN/MATERIAL:3110015714437
DELIVERY (IN DAYS):0085
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: DESTINATION
ACCEPTANCE POINT: DESTINATION
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:ZZ CLNG/DRY:1 PRESV MAT:ZZ
WRAP MAT:ZZ CUSH/DUNN MAT:ZZ CUSH/DUNN THKNESS:C
UNIT CONT:ZZ OPI:M
INTRMDTE CONT:ZZ INTRMDTE CONT QTY:0
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
PRESERVATION, PACKAGING, PACKING, AND MARKING REQUIREMENTS SHALL BE IN ACCORDANCE WITH MIL-DTL-197M.
1. METHOD OF PRESERVATION SHALL BE DETERMINED BY BEARING TYPE AND SIZE (REFER TO TABLE I).
2. PARAGRAPH 3.10.2, SELECTION OF UNIT PRESERVATION, APPLIES. PROTECTIVE LUBRICANT OR PRESERVATIVE COMPOUND SHALL BE DETERMINED DEPENDENT UPON BEARING TYPE AND CLOSURE IN ACCORDANCE WITH PARAGRAPH 3.3.4 AND TABLE II.
SPE4A6-26-T-16GZ
SECTION B
PR: 7017870011 PRLI: 0001 CONT’D
FOR PRESERVATION PROCESS CONTROLS, DEPENDANT
UPON BEARING TYPE, CLOSURE, AND LUBRICANT<(>,<)>
PARAGRAPHS 3.4 THROUGH 3.9 APPLY.
3. PACKAGING PRECAUTIONARY MARKING REQUIREMENTS
OF PARAGRAPH 3.12.4 APPLY.
4. CONTRACTOR'S PACKAGING FACILITY SHALL ADHERE
TO THE QUALITY ASSURANCE VERIFICATION
REQUIREMENTS AS CONTAINED WITHIN SECTION 4 OF
MIL-DTL-197M.
...END OF SPECIAL PACKAGING NSN/Part Number: 3110-01-571-4437 Quantity: 1,112 EA Purchase Request: 7017870011QTY: 1112 Delivery: 85 days ADO