This Solicitation opportunity from Department Of Defense was posted on July 23, 2026. The submission period has ended. Browse the details below for market research, or find similar active opportunities.
BRACKET, MOUNTING
Contract Overview
Solicitation details, issuing organization, response deadlines, documents, and interested companies for this government contract opportunity.
Active Opportunities Like This One
AI Contract Overview
The contract pertains to the procurement of one unit of a mounting bracket identified by NSN 5340016494439 under solicitation SPE7L1-26-T-827W, issued by the Defense Logistics Agency’s Land Supply Chain under the Department of Defense. The technical and quality requirements are governed by the DLA Master List of Technical and Quality Requirements, with specific provisions for packaging, sampling, inspection, and marking referenced by R-numbers such as RA001, RP001, and RQ011. The item must be manufactured in accordance with TDP Rev A Gen 1 aligned with reference drawing 19207 12580477-2 dated September 23, 2021, and all technical specifications take precedence over general commercial standards. Sampling must follow MIL-STD-1916 or ASQ H1331 Table 1, with critical, major, and minor attributes assigned verification levels VII, IV, and II or AQLs of 0.1, 1.0, and 4.0 respectively; unspecified attributes are treated as major. Zero non-conformances are required in sampled lots, even if MIL-STD-105 or ASQ Z1.4 is used for sample sizing. The unit must be delivered within five days after order date to Anniston Army Depot in Anniston, Alabama, with FOB origin terms, and shipping must be via the fastest traceable means—parcel post is prohibited. Packaging must adhere strictly to MIL-STD-129, DLA Packaging Requirements (RP001), and either ASTM D3951 for non-hazardous materials or TQ requirement IP025 if classified hazardous under FED-STD-313, with DLA requirements overriding all others. Hazardous materials require labeling per 29 CFR 1910.1200, and radioactive components must meet additional MIL-STD-129 markings. The contractor must comply with numerous FAR and DFARS clauses covering cybersecurity, whistleblower rights, trafficking in persons, equal opportunity, SAM maintenance, covered defense telecommunications equipment prohibitions, and safeguarding of controlled information. Additive manufacturing is explicitly prohibited for this item. All quotes must be submitted by July 23, 2026, through the DIBBS portal, with offerors required to maintain active SAM registration and
General Info
Agency
NAICS
Place of Performance
USASet-Aside
Timeline
Submission Closed
Organization & Contact Information
Full Description
BRACKET,MOUNTING
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
THE DRAWING(S) LISTED BELOW ARE AVAILABLE AT
DLA DURING "OPEN SOLICITATION ONLY".
TO RECEIVE A COPY OF THE DRAWING(S)<(>,<)>
FOR EBS SOLICITATIONS USE URL
HTTPS://WWW.DIBBS.BSM.DLA.MIL/RFQ/
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
RD003, COVERED DEFENSE INFORMATION POTENTIALLY APPLIES
TDP Rev A Gen 1 IAW BASIC DRAWING NR 19207 12580477 REVISION NR B DTD 07/16/2018 PART PIECE NUMBER: 12580477-2
TDP Rev A Gen 1 IAW REFERENCE DRAWING NR 19207 12472301 REVISION NR B DTD 09/25/2017 PART PIECE NUMBER:
TDP Rev A Gen 1 IAW REFERENCE DRAWING NR 19207 10875599 REVISION NR E DTD 10/22/1993 PART PIECE NUMBER:
TDP Rev A Gen 1 IAW REFERENCE DRAWING NR 19207 12577737
SPE7L1-26-T-827W
SECTION B
REVISION NR A DTD 01/29/2026
PART PIECE NUMBER:
TDP Rev A Gen 1 IAW REFERENCE DRAWING NR 19207 12580477-2 REVISION NR DTD 09/23/2021 PART PIECE NUMBER:
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 7015380960 0001 EA 1.000
NSN/MATERIAL:5340016494439
DELIVERY (IN DAYS):0005
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: DESTINATION
ACCEPTANCE POINT: DESTINATION
PREP FOR DELIVERY:
PKGING DATA-QUP:001
IF MATERIAL IS CONSIDERED HAZARDOUS IAW FED-STD-313,
PACKAGE IN ACCORDANCE WITH TQ REQUIREMENT IP025.
IF THE MATERIAL IS NOT CONSIDERED HAZARDOUS, IN ACCORDANCE WITH
FED-STD-313, THE MATERIAL SHALL BE COMMERCIALLY PACKAGED IN ACCORDANCE
WITH ASTM D3951.
All DLA Master List of Technical and Quality Requirements take precedence over ASTM D3951. Mark and label all packaging and packing in accordance with MIL-STD-129. The Unit of Issue (U/I) and Quantity per Unit Pack (QUP) will be as specified in the contract/purchase order. PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
BULK BREAK POINT:
W31G1Y
W0LX ANNISTON DEPOT PROP DIV
ANNISTON ARMY DEPOT BLDG 361
7 FRANKFORD AVE
ANNISTON AL 36201-5021
US
SHIP BY FASTEST TRACEABLE MEANS. DO NOT USE PARCEL POST.
FREIGHT SHIPPING ADDRESS:
SPE7L1-26-T-827W
SECTION B
PR: 7015380960 PRLI: 0001 CONT’D
W31G1Y
W0LX ANNISTON DEPOT PROP DIV
ANNISTON ARMY DEPOT BLDG 361
7 FRANKFORD AVE
ANNISTON AL 36201-5021
US
MARKFOR
W31G1Y
W0LX ANNISTON DEPOT PROP DIV
ANNISTON ARMY DEPOT BLDG 361
7 FRANKFORD AVE
ANNISTON AL 36201-5021
US
M/F: (TCN) W31G1Y602800NC
RDD: 035
PROJ: TP 1
SUPP ADD: W31G1Y SIG: A
FOR GOVERNMENT USE ONLY: (IPD) 03
DIC: A0A DIST: ADV: 2L FC: VE
Need Ship Date:00/00/0000 Original Required Delivery Date:02/02/2026
SPE7L1-26-T-827W NSN/Part Number: 5340-01-649-4439 Quantity: 1 EA Purchase Request: 7015380960QTY: 1 Delivery: 5 days ADO
More opportunities from Department Of Defense → LAND SUPPLY CHAIN
Same awarding agency
Find Active Opportunities Like This
Get AI-powered intelligence on the opportunities still open
Every page of the solicitation package shredded into a compliance breakdown
AI-powered matching based on your capabilities and past performance
Competitor and incumbent history on the requirement
Automated alerts on amendments, Q&A deadlines, and award
Join 650+ contractors already using CLEATUS