BRACKET, MULTIPLE ANGLE

BRACKET,MULTIPLE ANGLE
BRACKET,MULTIPLE ANGLE
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
IDENTIFY TO:
MIL-STD-130N, 16 Nov 2012 IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY
THE DRAWING(S) LISTED BELOW ARE AVAILABLE AT DLA DURING "OPEN SOLICITATION ONLY". TO RECEIVE A COPY OF THE DRAWING(S)<(>,<)> FOR EBS SOLICITATIONS USE URL HTTPS://WWW.DIBBS.BSM.DLA.MIL/RFQ/
The following Contract Data Requirements Lists (CDRLs), DD Form 1423s, apply to this procurement. Review the Technical Data Package (TDP) for additional information.
THE ITEM DESCRIBED IN THIS SOLICITATION IS DEFINED IN WHOLE OR IN PART BY ARMY DRAWING(S). THESE DRAWING(S) MAY CONTAIN A PAINT FINISHING REQUIREMENT. WHERE SUCH REQUIREMENTS ARE SPECIFIED, USE DCSC DRAWING 16236 CS-2300-0001 IN LIEU OF FINISH REQUIREMENTS OF THE ARMY DRAWING(S). THIS DRAWING
SPE7L1-27-T-1502
SECTION B
CONTAINS SPECIFICATIONS FOR CHEMICAL AGENT
RESISTANT COATINGS (CARC), AND ADDITIONAL
INFORMATION RELATING TO HIGH TEMPERATURE
COATINGS.
THIS NSN IS LISTED AS A PRIMARY QPL OR QML
THEREFORE THE QUALIFIED PRODUCTS LIST OR
QUALIFIED MANUFACTURERS LIST IS APPLICABLE.
THIS IS A PERFORMANCE REVIEW INSTITUTE (PRI) QML OR QPL ITEM. PRODUCT
SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED
MANUFACTURER (FOR COMPONENTS) AND/OR ASSEMBLED BY AN ACCREDITIED
MANUFACTURER OR ACCREDITED ASSEMBLING DISTRIBUTOR (FOR ASSEMBLIES) AS
LISTED IN THE PRI QUALIFIED MANUFACTURER LIST (QML)OR QUALIFIED PRODUCTS
LIST (QPL) FOR THIS STANDARD. THE QML OR QPL IS AVAILABLE AT
WWW.EAUDITNET.COM.
RQ016: COMPONENT QUALIFIED PRODUCTS LISTS (QPL)/QUALIFIED MANUFACTURERS
LISTS (QML). THIS ITEM CONTAINS ONE OR MORE COMPONENTS DEFINED BY A
SPECIFICATION(S) WITH AN ASSOCIATED QUALIFIED PRODUCTS LIST (QPL) OR
QUALIFIED MANUFACTURERS LIST (QML). QUALIFICATION REQUIREMENTS IN
PROCUREMENT NOTE H02 "COMPONENT QUALIFIED PRODUCTS LIST (QPL)/QUALIFIED
MANUFACTURERS LIST (QML)" APPLY.
TDP Rev A Gen 1 IAW BASIC DRAWING NR 19207 12421384 REVISION NR A DTD 02/04/1999 PART PIECE NUMBER: 12421384-001
TDP Rev A Gen 1 IAW REFERENCE DRAWING NR 19207 12420325 REVISION NR D DTD 12/19/2003 PART PIECE NUMBER:
TDP Rev A Gen 1 IAW REFERENCE DRAWING NR 19207 12421384-001 REVISION NR DTD 07/21/2010 PART PIECE NUMBER:
TDP Rev A Gen 1 IAW REFERENCE UNK QPL-53022-14 NOT 1 REVISION NR 14 DTD 01/25/2008 PART PIECE NUMBER:
TDP Rev A Gen 1 IAW REFERENCE UNK QPL-53030-7 NOT 1 REVISION NR 7 DTD 02/07/2008 PART PIECE NUMBER:
TDP Rev A Gen 1 IAW REFERENCE UNK QPL-53084-6 NOT 1 REVISION NR 6 DTD 06/16/2008 PART PIECE NUMBER:
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
SPE7L1-27-T-1502
SECTION B
PR: 7018558662 PRLI: 0001 CONT’D
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 7018558662 0001 EA 4.000
NSN/MATERIAL:5340014802500
DELIVERY (IN DAYS):0005
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: DESTINATION
ACCEPTANCE POINT: DESTINATION
PREP FOR DELIVERY:
PKGING DATA-QUP:001
WILL BE PACKAGED IN ACCORDANCE WITH ASTM D3951.
All DLA Master List of Technical and Quality Requirements take precedence over ASTM D3951. Mark and label all packaging and packing in accordance with MIL-STD-129. The Unit of Issue (U/I) and Quantity per Unit Pack (QUP) will be as specified in the contract/purchase order. PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
BULK BREAK POINT:
W81XB9
W8SE MI ARNG FMS 02
25045 SOUTH PERIMETER ROAD
BLDG 1492
SELFRIDGE MI 48045-5026
US
RDD(3-POS RDD)/NMCS SHIPMENT. SHIP BY FASTAST TRACEABLE MEANS. DO NOT USE PARCEL POST.
FREIGHT SHIPPING ADDRESS:
W81XB9
W8SE MI ARNG FMS 02
25045 SOUTH PERIMETER ROAD
BLDG 1492
SELFRIDGE MI 48045-5026
US
MARKFOR
W81XB9
W8SE MI ARNG FMS 02
25045 SOUTH PERIMETER ROAD
BLDG 1492
SELFRIDGE MI 48045-5026
US
M/F: (TCN) W81XB962680165
RDD: N
PROJ: TP 1
SUPP ADD: W80X71 SIG: A
SPE7L1-27-T-1502
SECTION B
PR: 7018558662 PRLI: 0001 CONT’D
FOR GOVERNMENT USE ONLY: (IPD) 03
DIC: A3A DIST: ADV: FC: 62
Need Ship Date:00/00/0000 Original Required Delivery Date:09/30/2026
SPE7L1-27-T-1502 NSN/Part Number: 5340-01-480-2500 Quantity: 4 EA Purchase Request: 7018558662QTY: 4 Delivery: 5 days ADO