CLOTH, PLAIN WEAVE

CLOTH,PLAIN WEAVE
CLOTH,PLAIN WEAVE
.
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
INDIVIDUAL NSN DATA
.
NSN 8305-01-007-8305; PGC90099
.
ITEM NAME: ,,CLOTH,PLAIN WEAVE
PART NUMBER: ,,AMS-C-9084
CAGE Code: ,,0U583; SAE INTERNATIONAL . Shall be in accordance with(IAW) Aerospace Material Specification AMS-C-9084, Cloth, Glass, Finished, For Resin Laminates, issued 199-06 and Reaffirmed 2013-07. . . . . Intended for use in fabricating resin laminates and plastic sandwich materials for structural parts, radio and radar antenna housings, fairings, and other applications. . Width: 37.75 inches minimum to 38.50 inchese maximum, inclusive of the selvages Weave type: Plain Thickness: 0.0065 inches minimum to 0.0085 inches maximum Special features: Used for epoxy laminates Weight: 5.77 ounces per square yard nominal; 5.42 ounces per square yard minimum to 6.12 ounces per square yard maximum Fiber material: Glass basic Color: Natural both sides Procurement Group Code (PGC): 90099 Type: IV Commercial Designation: 128 Class: 2 (For epoxy laminates) Roll Length: 100 yards minimum to 150 yards maximum . Unit of issue is a YARD (YD). . Certification: The test requirements for mechanical properties, electricial properties, or both mechanical and electrical properties of the laminates may be satisfied by the supplier's certificate of conformity to these requirements supported by certified test data showing that the cloth finished by the same supplier, of identical type,
SPE1C1-26-T-0705
SECTION B
class, and finish, has previously been subjected to and has passed the applicable tests for laminate properties under this specification. . TEST REPORTS AND COMPONENT CERTIFICATIONS IN ACCORDANCE WITH Revision 1 of the DLA TROOP SUPPORT CLOTHING & TEXTILES ADDITIONAL QUALITY ASSURANCE REQUIREMENTS dated August 2021 ARE REQUIRED WITH ALL CONTRACT COMPONENT LOTS. . SOURCES OF COMPONENT MATERIALS SHALL BE IDENTIFIED<(>,<)> INCLUDING APPLICABLE SPECIFICATIONS, AND SHALL NOT BE CHANGED THROUGHOUT THE LIFE OF THE CONTRACT WITHOUT REQUEST AND APPROVAL BY THE DLA TROOP SUPPORT CONTRACTING OFFICER THROUGH MODIFICATION TO THE CONTRACT.
RESPONSIBILITY OF INSPECTION. THE CONTRACTOR IS RESPONSIBLE FOR THE PERFORMANCE OF ALL INSPECTION<(>,<)> EXAMINATION, AND TEST REQUIREMENTS SPECIFIED HEREIN AND IN THE SITED SPECIFICATIONS AND CONTRACT. THE GOVERNMENT RESERVES THE RIGHT TO PERFORM ANY OF THE INSPECTIONS, EXAMINATIONS AND TESTS AS DEEMED NECESSARY TO ENSURE SUPPLIES AND SERVICES CONFORM TO PRESCRIBED REQUIREMENTS. . . RT001: MEASURING AND TEST EQUIPMENT
.
FED-STD-595C, COLORS USED IN GOVERNMENT PROCUREMENT, AND ALL ASSOCIATED
SLASH SHEETS HAVE BEEN CANCELLED (FEBRUARY 14, 2017) AND SUPERSEDED BY
SAE AMS-STD-595.
ADDITIONAL INFORMATION FOR SAE AMS-STD-595:
COPIES OF SAE AMS-STD-595 CAN BE OBTAINED FROM:
WEBSITE: STORE.SAE.ORG/EA/
TELEPHONE: +1 (555) 000-0000 (INSIDE USA AND CANADA)
+1 (555) 000-0000 (OUTSIDE USA)
MAIL: SAE CUSTOMER SERVICE
400 COMMONWEALTH DRIVE
WARRENDALE, PA 15096-0001
.
.
.
LIST OF DOCUMENTS, EXHIBITS, AND OTHER ATTACHMENTS
a. This solicitation/award consists of the following documents, exhibits, and other attachments b. DLA Troop Support Clothing & Textiles Additional Quality Assurance Requirements Revision 1 dated August 2021, which has superseded DLA Troop Support Clothing and Textiles Additional Quality Assurance Requirements dated October 2018. . 52.246-15 CERTIFICATE OF CONFORMANCE
. . Identification of Testing Sites. Unless the contract mandates a Government laboratory be used to conduct testing, the prime contractor shall identify all testing sites that will perform any test required by the terms of the contract, including end item testing.
Any laboratory proposed by the contractor is subject to the approval of the contracting officer. Testing facilities shall be subject to on-site witnessing of testing by the Government. The use of a laboratory previously approved by the Government is not a guarantee that testing will be performed properly, nor does it relieve a contractor from the contractual obligation to present conforming supplies accompanied by
SPE1C1-26-T-0705
SECTION B
true, accurate, and valid test results.
Certification of Testing Sites. The prime contractor shall identify a technical point of contact for the testing site and provide current contact information. The prime contractor should alert the technical point of contact that the certification process has begun. A current ISO 17025 accreditation whose scope encompasses the contractual testing or equivalent will be accepted. When a testing site and its contact information are provided to DLA Contracting and the DLA Product Specialist, the product specialist will initiate a request for the DLA Product Test Center (DLA-PTC) to certify the lab. This request will be managed via an internal DLA Troop Support process.
In the absence of an appropriate ISO 17025 accreditation, the DLA-PTC will compare all required testing in the contract to the commercial lab capability. If the testing facility is new and/or unknown to the DLA-PTC, a lab certification survey (DLA Form 6005) will be provided for submission.
If the DLA-PTC has a lab survey on file that is less than 3 years old, that survey will be used for the initial NSN/Part Number: 8305-01-007-8305 Quantity: 1 YD Purchase Request: 7015822375QTY: 1 Delivery: 20 days ADO