CONTRACTOR FIRST ARTIC

GUIDE,CARTRIDGE,SMA
GUIDE, FEED SLIDE. STEEL FORGING.
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
THIS ITEM IS A "DEFENSE ARTICLE" AS DEFINED IN
AND SUBJECT TO THE INTERNATIONAL TRAFFIC IN ARMS
REGULATIONS (22 C.F.R. 120-30) AND THE ARMS EXPORT
CONTROL ACT (22 U.S.C.A. 2778-2799). ANY
MANUFACTURER OR EXPORTER OF DEFENSE ARTICLES IS
REQUIRED TO REGISTER WITH THE DIRECTORATE OF DEFENSE
TRADE CONTROLS (DDTC), DEPARTMENT OF STATE.
DOCUMENTARY EVIDENCE OF REGISTRATION MAY BE REQUIRED
PRIOR TO AWARD. ADDITIONAL EXPORT RESTRICTIONS
APPLY AS INDICATED HEREIN. FAILURE TO SUBMIT DDTC
REGISTRATION WHEN REQUESTED WILL MAKE A QUOTE/OFFER
INELIGIBLE FOR AWARD.
______________EXCEPTION DATA__________________
IF DRAWING NOTE GIVES OPTION FOR ZINC OR
MANGANESE COATING THEN MANGANESE IS REQUIRED.
PRODUCT:
PRON CVP2508350
DR 7793233:
IN HEAT TREATMENT BLOCK OF TITLE BLOCK: CHANGE FROM “MIL-H-6875” TO “SAE
AMS2759”.
IN ZONE C4: CHANGE FROM MIL-I-6868” TO “ASTM E1444/E1444M“.
IN ZONE C4: CHANGE FROM MIL-I-6866” TO “ASTM E1417/E1417M“.
ENGINEERING – INSPECTION DRAWINGS AND DISCREPANCY NOTICE INCLUDED IN
TDPL/TDP
THE FOLLOWING DRAWINGS ARE BEING PROVIDED SOLELY FOR INFORMATIONAL
PURPOSES. THE USG MAKES NO REPRESENTATION OR WARRANTIES, EXPRESS OR
IMPLIED, REGARDING THE ACCURACY, COMPLETENESS, OR SUITABILITY OF THIS
DRAWING FOR ANY SPECIFIC USE.
FURTHERMORE, THE USG DISCLAIMS ALL LIABILITY FOR ANY ERRORS, OMISSIONS,
OR OUTCOMES RESULTING FOR THE USE OR RELIANCE ON THIS DRAWING.
11015555
11015629
11015663
SPE7L7-26-T-3710
SECTION B
11015814
11016248
11016329
7272792
7797013
7797016
7797035
7797036
7797037
7797134
7797135
7797234
7797351
7797374
7797414
7797453
7797508
TO ENGINEERING TECHNICIAN:
THE SUBJECT DRAWING 7272911 WAS NOT CONFIGURED IN THE SYSTEM. PLEASE
DELETE THE DEFICIENCY AND HAVE DRAWING 7272911 ADDED TO THE PRON.
____________END OF EXCEPTIONS________________
________SPECIAL PACKAGING INSTRUCTIONS_______
ADD SPI AM7793233 REVISION 'E' TO THE TDP.
____END OF SPECIAL PACKAGING INSTRUCTIONS____
THE ITEM BEING PROCURED IS A CRITICAL GUN PART
ITEM WITH UNIQUE REQUIREMENTS.
CONTRACTOR FAT APPLIES.
AFTER RECEIPT OF QUOTES, OFFERORS MAY BE
CONTACTED TO PRICE THE FAT REQUIREMENT.
PROCESS PROCEDURES AND OR WORKMANSHIP SPECIMENS
REQUIRED BY MILITARY SPECIFICATION (S) APPLICABLE
TO THIS CONTRACT WILL BE APPROVED BY THE CONTRACT
POST AWARD CONTRACTING OFFICER (PCO).
PRODUCT INSPECTION WILL BE CONDUCTED BY THE DCMA
QAR AT THE ACTUAL MANUFACTURER'S FACILITY.
THE IDENTIFICATION OF THE ACTUAL
MANUFACTURER AND PHOSPHATE CONTRACTOR MUST BE
SUBMITTED TO THE CONTRACTING OFFICER FOR
INCLUSION IN THE AWARD. UPON AWARD, ANY CHANGES
TO THE ABOVE MUST BE APPROVED BY THE PCO VIA
FORMAL CONTRACT MODIFICATION.
PRODUCT VERIFICATION TESTING (PVT) IN ACCORDANCE
WITH PROCUREMENT NOTE E05, MAY BE INVOKED FOR THE
REFERENCED CONTRACT. IF INVOKED, PVT SAMPLES MUST BE
INSPECTED, PACKAGED AND MARKED AS REQUIRED IN THE
CONTRACT. ONE (1) SAMPLE MAY BE DESTROYED DURING
TESTING.
PRODUCT VERIFICATION TESTING, IF INVOKED<(>,<)>
WILL BE PERFORMED PRIOR TO ACCEPTANCE OF
EACH SHIPMENT. THE CONTRACTOR MUST PROVIDE
PVT SAMPLES FROM EACH (SUB)CONTRACTOR USED
IN THE PRODUCTION OF PARTS ON THIS CONTRACT.
FIVE (5) PVT SAMPLES, UNLESS OTHERWISE
SPE7L7-26-T-3710
SECTION B
SPECIFIED, WILL BE REQUIRED TO BE IDENTIFIED
TO THOSE (SUB)CONTRACTORS WHEN THEY ARE SENT
IN FOR TESTING.
CERTIFICATE OF CONFORMANCE IS NOT AUTHORIZED.
*************************************************************
RD001: DEMILITARIZATION: SMALL ARMS WEAPONS AND PARTS AND ACCESSORIES
(CATEGORY I MUNITIONS LIST ITEMS, CATEGORY I-DODM 4160.28-VOL.3)
RD002, COVERED DEFENSE INFORMATION APPLIES
RD005: Cybersecurity Maturity Model Certification (CMMC) Level 2 Certified Third-Party Assessment Organization (C3PAO)
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS
(MANUFACTURERS AND NON-MANUFACTURERS)
RQ002: CONFIGURATION CHANGE MANAGEMENT ENGINEERING CHANGE PROPOSAL
REQUEST FOR VARIANCE (DEVIATION OR WAIVER)
RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RQ016: COMPONENT QUALIFIED PRODUCTS LISTS (QPL)/QUALIFIED MANUFACTURERS
LISTS (QML). THIS ITEM CONTAINS ONE OR MORE COMPONENTS DEFINED BY A
SPECIFICATION(S) WITH AN ASSOCIATED QUALIFIED PRODUCTS LIST (QPL) OR
QUALIFIED MANUFACTURERS LIST (QML). QUALIFICATION REQUIREMENTS IN
PROCUREMENT NOTE H02 "COMPONENT QUALIFIED PRODUCTS LIST (QPL)/QUALIFIED
MANUFACTURERS LIST (QML)" APPLY.
RQ036Phosphate Coating Supplier Certification Requirements
RT001: MEASURING AND TEST EQUIPMENT
CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE
USED NOR INCORPORATED IN ANY ITEMS TO BE
DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION
SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT
DOES NOT ALLEVIATE ANY PRODUCT REQUIREMENTS.
SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR
APPROVAL UNLESS THEY ARE AUTHORIZED BY THE
SPECIFICATION REQUIREMENTS.
A forging process was identified as a means to manufacture this item. Tooling is required to produce a forging. For sourcing, tooling, materials or other information, please contact the appropriate
SPE7L7-26-T-3710
SECTION B
assistance team: (Aviation, C<(>&<)>E Supply Chains) https://www.dla.mil/Aviation/Offers/Engineering/Forging-and-Casting/; (Land & Maritime Supply Chains) DSCC.cast.forge@dla.mil.
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
RQ032: EXPORT CONTROL OF TECHNICAL DATA
This item has technical data some or all of which is subject to export-control of either the International Traffic in Arms regulations (ITAR) or the Export Administration Regulations (EAR), and cannot be exported without prior authorization from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and nationals whether located in the United States or abroad. This requirement applies equally to foreign national employees and U.S. companies and their foreign subsidiaries. DFARS 252.225-7048 is applicable to this data.
The Defense Logistics Agency (DLA) limits distribution of export-control technical data to DLA contractors that have an approved US/Canada Joint Certification Program (JCP) certification, have completed the Introduction to Proper Handling of DOD Export-Controlled Technical Data Training and the DLA Export-Controlled Technical Data Questionnaire (both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. NSN/Part Number: 0001S00000053 Quantity: 3 EA Purchase Request: 7016971080QTY - See Solicitation Delivery: 155 days ADO