COVER, AMMUNITION CAN

COVER, AMMUNITION CAN
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
THIS ITEM IS A "DEFENSE ARTICLE" AS DEFINED IN AND SUBJECT TO THE
INTERNATIONAL TRAFFIC IN ARMS REGULATIONS (22 C.F.R. 120-30) AND THE
ARMS EXPORT CONTROL ACT (22 U.S.C.A. 2778-2799). ANY MANUFACTURER OR
EXPORTER OF DEFENSE ARTICLES IS REQUIRED TO REGISTER WITH THE
DIRECTORATE OF DEFENSE TRADE CONTROLS (DDTC), DEPARTMENT OF STATE.
DOCUMENTARY EVIDENCE OF REGISTRATION MAY BE REQUIRED PRIOR TO AWARD.
ADDITIONAL EXPORT RESTRICTIONS APPLY AS INDICATED HEREIN. FAILURE TO
SUBMIT DDTC REGISTRATION WHEN REQUESTED WILL MAKE A QUOTE/OFFER
INELIGIBLE FOR AWARD.
______________EXCEPTION DATA__________________
PRON DRAWING 12295226 NOTE 9 PROTECTIVE FINISH CALLS OUT PARAGRAPH 3.4
OF INTERIOR PAINT SYSTEM DRAWING 12350824. NON-SKID CARC VARIANTS
12308492 AND 12308493 ARE NOT CALLED OUT IN THIS PARAGRAPH AND THEREFORE
SHOULD NOT BE INCLUDED IN THE TDP DX 12308492 DX 12308493 HAS UAMA
B874.12 ON THE DRAWING, THIS IS INCORRECT AND SHOULD SAY UAMA B74.12 ON
THE DRAWING
TDPL:
REMOVE 12308492
REMOVE 12308493
Add PD AM12295226 REV
____________END OF EXCEPTIONS________________
________SPECIAL PACKAGING INSTRUCTIONS_______
____END OF SPECIAL PACKAGING INSTRUCTIONS____
THE ITEM BEING PROCURED IS A CRITICAL GUN PART
ITEM WITH UNIQUE REQUIREMENTS.
CONTRACTOR FAT APPLIES.
AFTER RECEIPT OF QUOTES, OFFERORS MAY BE
CONTACTED TO PRICE THE FAT REQUIREMENT.
PROCESS PROCEDURES AND OR WORKMANSHIP SPECIMENS
REQUIRED BY MILITARY SPECIFICATION (S) APPLICABLE
TO THIS CONTRACT WILL BE APPROVED BY THE CONTRACT
POST AWARD CONTRACTING OFFICER (PCO).
PRODUCT INSPECTION WILL BE CONDUCTED BY THE DCMA
QAR AT THE ACTUAL MANUFACTURER'S FACILITY.
SPE7L7-27-Q-0200
SECTION B
SUPPLY/SERVICE: 1005-01-110-3421 CONT'D
THE IDENTIFICATION OF THE ACTUAL
MANUFACTURER AND PHOSPHATE CONTRACTOR MUST BE
SUBMITTED TO THE CONTRACTING OFFICER FOR
INCLUSION IN THE AWARD. UPON AWARD, ANY CHANGES
TO THE ABOVE MUST BE APPROVED BY THE PCO VIA
FORMAL CONTRACT MODIFICATION.
PRODUCT VERIFICATION TESTING (PVT) IN ACCORDANCE
WITH PROCUREMENT NOTE E05, MAY BE INVOKED FOR THE
REFERENCED CONTRACT. IF INVOKED, PVT SAMPLES MUST BE
INSPECTED, PACKAGED AND MARKED AS REQUIRED IN THE
CONTRACT. ONE (1) SAMPLE MAY BE DESTROYED DURING
TESTING.
THIS NSN CONTAINS ONE OR MORE COMPONENTS WHICH
MUST MEET QPL/QML SPECIFICATIONS AS IDENTIFIED IN
THE TECHNICAL DATA PACKAGE. (FAR CLAUSE 52.209-1)
QUALIFICATION REQUIREMENTS IS APPLICABLE. THE
AWARDEE SHALL PROVIDE QPL/QML COMPONENTS ONLY FROM
SOURCES QUALIFIED ON THE APPLICABLE QPL(S)/QML(S).
THE IDENTIFICATION OF ALL APPLICABLE QPL/QML SOURCES
MUST BE SUBMITTED TO THE CONTRACTING OFFICER FOR NSN/Part Number: 1005-01-110-3421 Quantity: 17 EA Purchase Request: 7014129778QTY: 17 Delivery: 332 days ADO