DISK ASSEMBLY

DISK ASSEMBLY
DISK ASSEMBLY.
A forging process was identified as a means to manufacture this item. Tooling is required to produce a forging. For sourcing, tooling, materials or other information, please contact the appropriate assistance team: (Aviation, C<(>&<)>E Supply Chains) https://www.dla.mil/Aviation/Offers/Engineering/Forging-and-Casting/; (Land & Maritime Supply Chains) DSCC.cast.forge@dla.mil. RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS
(MANUFACTURERS AND NON-MANUFACTURERS)
RQ002: CONFIGURATION CHANGE MANAGEMENT ENGINEERING CHANGE PROPOSAL
REQUEST FOR VARIANCE (DEVIATION OR WAIVER)
RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
WELDED CONSTRUCTION, BALANCING REQUIRED. ITEM REQUIRES CRITICAL WELDING
PER DRAWING 10861595. THESE WELDS MUST MEET THE REQUIREMENTS OF DRAWING
12479550, WHICH INCLUDES BUT NOT LIMITED TO A PREPRODUCTION SUBMISSION
OF THE CONTRACTOR'S WELDING PROCEDURE SPECIFICATION
SPE7L3-26-T-257G
SECTION B
"CONTRACTOR NOTE: COMPUTER NUMERICALLY
CONTROLLED (CNC) MACHINE AND STANDARD
INDUSTRY INSPECTION EQUIPMENT, WHICH
PROVIDE EQUAL OR GREATER ACCURACY, MAY
BE UTILIZED IN LIEU OF U.S. ARMY DESIGNED
INSPECTION EQUIPMENT, (GAGES AND FIXTURES),
DESCRIBED IN THE DATA PACKAGE PROVIDED".
CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE
USED NOR INCORPORATED IN ANY ITEMS TO BE
DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION
SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT
DOES NOT ALLEVIATE ANY PRODUCT REQUIREMENTS.
SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR
APPROVAL UNLESS THEY ARE AUTHORIZED BY THE
SPECIFICATION REQUIREMENTS.
"FINAL INSPECTION AND ACCEPTANCE OF THE ITEM
SHALL BE AT THE ACTUAL MANUFACTURING FACILITY.
TECHNICAL INSPECTION IS REQUIRED. THE
CONTRACTOR SHALL MAKE DRAWINGS AND TECHNICAL
INFORMATION AVAILABLE TO VERIFY THAT THE ITEM
MEETS ALL TECHNICAL REQUIREMENTS.
COUNT, KIND, AND CONDITION INSPECTIONS ARE
NOT ACCEPTABLE. THIS NOTE TAKES PRECEDENCE OVER
MASTER SOLICITATION PART ONE PROVISIONS, NOTE 6,
QUOTATIONS BY NON-MANUFACTURERS (APR 1984,
DCSC 52.217-9C01). FINAL INSPECTION OF
PACKAGING, IF REQUIRED, MAY BE CONDUCTED
ELSEWHERE."
RD003, COVERED DEFENSE INFORMATION POTENTIALLY APPLIES
CRITICAL APPLICATION ITEM
TDP Rev A Gen 1 IAW BASIC DRAWING NR 19207 10861595 REVISION NR L DTD 01/01/1999 PART PIECE NUMBER:
TDP Rev A Gen 1 IAW REFERENCE QAP 19207 10861594 REVISION NR C DTD 05/24/1988 PART PIECE NUMBER:
TDP Rev A Gen 1 IAW REFERENCE QAP 19207 10861595 REVISION NR G DTD 12/19/1979 PART PIECE NUMBER:
TDP Rev A Gen 1 IAW REFERENCE QAP 19207 10861597 REVISION NR C DTD 11/14/1977 PART PIECE NUMBER:
TDP Rev A Gen 1 IAW REFERENCE QAP 19207 10861624 REVISION NR E DTD 08/18/1969 PART PIECE NUMBER:
TDP Rev A Gen 1 IAW REFERENCE QAP 19207 10861627 REVISION NR B DTD 04/08/1966 PART PIECE NUMBER:
TDP Rev A Gen 1 IAW REFERENCE DRAWING NR 19207 8301278
SPE7L3-26-T-257G
SECTION B
REVISION NR C DTD 10/08/1965
PART PIECE NUMBER: GAGE
TDP Rev A Gen 1 IAW REFERENCE DRAWING NR 19207 10861586 REVISION NR H DTD 01/01/1999 PART PIECE NUMBER:
TDP Rev A Gen 1 IAW REFERENCE DRAWING NR 19207 10861594 REVISION NR G DTD 01/01/1999 PART PIECE NUMBER:
TDP Rev A Gen 1 IAW REFERENCE DRAWING NR 19207 10861597 REVISION NR H DTD 01/01/1999 PART PIECE NUMBER:
TDP Rev A Gen 1 IAW REFERENCE DRAWING NR 19207 10861624 REVISION NR P DTD 09/06/2000 PART PIECE NUMBER:
TDP Rev A Gen 1 IAW REFERENCE DRAWING NR 19207 10861627 REVISION NR F DTD 09/06/2000 PART PIECE NUMBER:
TDP Rev A Gen 1 IAW REFERENCE DRAWING NR 19207 10861595 REVISION NR DTD 11/21/2022 PART PIECE NUMBER:
TDP Rev A Gen 1 IAW REFERENCE DRAWING NR 21450 BMCX1.1 REVISION NR 4 DTD 02/06/1961 PART PIECE NUMBER:
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 7018379736 0001 EA 9.000
NSN/MATERIAL:2520006797959
DELIVERY (IN DAYS):0180
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: ORIGIN
ACCEPTANCE POINT: ORIGIN
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:33 CLNG/DRY:1 PRESV MAT:49
SPE7L3-26-T-257G
SECTION B
PR: 7018379736 PRLI: 0001 CONT’D
WRAP MAT:GB CUSH/DUNN MAT:JC CUSH/DUNN THKNESS:A
UNIT CONT:ED OPI:M
INTRMDTE CONT:E5 INTRMDTE CONT QTY:004
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:00 -00 No special marking
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
IP025: PACKAGING, MARKING, AND SHIPPING OF HAZARDOUS MATERIALS
PARCEL POST ADDRESS:
W25G1U
W1A8 DLA DISTRIBUTION
DDSP NEW CUMBERLAND FACILITY
2083 NORMANDY DRIVE DOOR 113 TO 134
NEW CUMBERLAND PA 17070-5002
US
FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE
C20 AND CONTRACT
FREIGHT SHIPPING ADDRESS:
W25G1U
W1A8 DLA DISTRIBUTION
DDSP NEW CUMBERLAND FACILITY
2083 NORMANDY DRIVE DOOR 113 TO 134
NEW CUMBERLAND PA 17070-5002
US
Need Ship Date:03/28/2027 Original Required Delivery Date:03/28/2027
SPE7L3-26-T-257G NSN/Part Number: 2520-00-679-7959 Quantity: 9 EA Purchase Request: 7018379736QTY: 9 Delivery: 180 days ADO