DRAWBOLT, TEST AND MAIN

DRAWBOLT,TEST AND MAINTENANCE STAND
DRAWBOLT, TEST AND M
ENGINERRING NOTES: 1. PART MARKING PER MIL-STD-130, METHOD PER THE
DRAWING REQUIREMENTS AND BAC 5307. MARKING MUST INCLUDE NATIONAL STOCK
NUMBER, PART NUMBER, CURRENT DESIGN AUTHORITY CODE (98748), ACTUAL
MANUFACTURER'S CAGE CODE (-----), DATE OF MANUFACTURE, AND "FOR
MILITARY USE ONLY". PARTS WILL NOT BE MARKED WITH THE ORIGINAL DESIGN
AUTHORITY (BOEING) CAGE CODE. 2. SURFACE TEXTURE PER ASME B46.1 ILO BACD
2097. 3. DIMENSIONS AND TOLERANCES PER ASME Y14.5. 4. USE 4140 STEEL
BAR/ROD/FORGING PER SAE AMS 6382 IN LIEU OF MIL-S-5626. 5. FINISH CODE
F-1.977 DEFINED: CADMIUM PLATE ACCORDING TO SAE AMS-QQ-P-416, TYPE II,
CLASS 1. BAKE 3 HOURS MINIMUM AT 375 ± 25 F. 6. USE FED-STD-H28 (SCREW
THREAD STANDARDS) ILO THREADS PER HANDBOOK H-28. / THIS PRODUCT HAS BEEN
DETERMINED TO BE OR CONTAINS (AS CHECKED BELOW): ____ ENGINEERING
CRITICAL IN APPLICATION. ___ MAJOR CHARACTERISTICS. X_ MINOR
CHARACTERISTICS, ALL EXCEPT CRITICAL AND MAJOR. 8. WHEN MATERIALS,
PROCESSES OR COMPONENTS ARE TO BE OBTAINED FROM DIRECTED SOURCES AS
INDICATED HEREIN OR IN THE SPECIFICATIONS, ALTERNATE SOURCES MAY ONLY BE
UTILIZED UPON PRIOR APPROVAL BY THE CONTRACTING OFFICER OF THIS
PROCURING ACTIVITY AS A DEVIATION. BIDDERS SHALL NOTIFY THIS PROCURING
ACTIVITY AT THE TIME OF QUOTATION OF ANY DRAWING, SPECIFICATION OR
STANDARD WHICH IS OF MORE CURRENT DATA REVISION THAN THOSE SHOWN ON THE
DATA LISTING OR IN THESE ENGINEERING NOTES. DETERMINATION OF
ACCEPTABILITY OF THE MORE CURRENTLY DATED DATA WILL BE MADE BY THE
RESPONSIBLE ENGINEERING OFFICE OF THIS PROCURING ACTIVITY. LOWER TIER
SPECIFICATIONS LISTED IN OR REFERENCED BY FIRST TIER SPECIFICATIONS MAY
NOT BE SHOWN ON THE DATA LISTS OR ENGINEERING NOTES ACCOMPANYING THIS
CONTRACT BUT ARE NONETHELESS REQUIRED BY THIS CONTRACT FOR COMPLIANCE.
EXCEPTIONS WOULD OCCUR ONLY WHEN SUCH LOWER TIER REQUIREMENTS HAVE BEEN
SPECIFICALLY WAIVED OR SUBSTITUTE SPECIFICATIONS/REQUIREMENTS ARE
DESIGNATED HEREIN. REPORTS, PROCESS SHEETS, INSPECTION METHODS SHEETS
AND ALL OTHER DOCUMENTS REQUIRED BY SPECIFICATIONS IMPOSED BY THIS
CONTRACT FOR CONTRACTOR COMPLIANCE WHICH WERE PREVIOUSLY REQUIRED TO BE
SUBMITTED TO A PRIME DESIGN CONTRACTOR SHALL BE HELD AT THAT FACILITY
FOR REVIEW BY GOVERNMENT PERSONNEL. WHEN PRIME DESIGN SOURCE
SPECIFICATIONS REQUIRE OR PROVIDE FOR PARTICIPATION BY THAT PRIME SOURCE
QUALITY, MANUFACTURING, LABORATORY OR ENGINEERING SUPPORT SERVICES,
THESE REQUIREMENTS OR PROVISIONS DO NOT APPLY WHEN THE CONTRACT WAS
ISSUED BY THIS PROCURING ACTIVITY. FOR THESE SERVICES OR DIRECTION
PERTAINING THERETO, CONTACT THE COGNIZANT GOVERNMENT CONTRACT
ADMINISTRATION OFFICE OR THIS PROCURING ACTIVITY FOR ASSISTANCE. THE
CONTRACTOR IS RESPONSIBLE FOR ASSURING THAT ALL DIMENSIONS, CONDITIONS,
TESTS AND TEST RESULTS IDENTIFIED IN THESE ENGINEERING NOTES, APPLICABLE
DRAWINGS, SPECIFICATIONS AND CONTRACT QUALITY REQUIREMENTS ARE MET BY
THEMSELVES AND THEIR SUPPLIERS. THIS REQUIREMENT APPLIES TO ALL
CHARACTERISTICS WHETHER THOSE CHARACTERISTICS HAVE BEEN SPECIFICALLY
DESIGNED AS BEING CRITICAL, MAJOR OR ARE THOSE MINOR CHARACTERISTICS NOT
SPECIFICALLY DESIGNATED AS SUCH.
A SAMPLE QTY OF 2 SHALL BE TESTED IAW ALL TECHNICAL DATA PROVIDED IN
THE CONTRACT. -A COMPLETE TEST PLAN SHALL BE SUBMITTED TO THE FOLLOWING
ADDRESS FOR APPROVAL: / CONTRACTOR SHALL NOTIFY THE ACO AND AFNWC/NDMES,
BLDG 469, TINKER AFB, OK 74145-8901, 7 DAYS PRIOR TO START OF TESTING. /
A COMPLETE FIRST ARTICLE TEST REPORT SHALL BE SUBMITTED TO THE FOLLOWING
ADDRESS AT THE COMPLETION OF THE TESING: OC-ALC/ENSDD FA MONITOR
DODAAC FA8111 3001 STAFF DRIVE, STE 1AB85A TINKER AFB, OK 73145-3041 /
SAMPLES MAY BE CONSIDERED AS PART OF THE PRODUCTION QUANTITY, BUT SHALL
NOT BE CONSIDERED A MANUFACTURES STANDARD.
Casting/forging may be required to manufacture this NSN and tooling is typically involved. The government may not have this special tooling. For sourcing, tooling, materials or other information, please submit a Casting and Forging Assistance Request at either https://www.dla.mil/Aviation/Offers/Engineering/Forging-and-Casting/ or Land & Maritime Supply Chains contact@example.gov. Casting/forging may be required to manufacture this NSN and tooling is
SPE4A7-27-T-3364
SECTION B
typically involved. The government may not have this special tooling. For sourcing, tooling, materials or other information, please submit a Casting and Forging Assistance Request at either https://www.dla.mil/Aviation/Offers/Engineering/Forging-and-Casting/ or Land & Maritime Supply Chains contact@example.gov. RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RD002, COVERED DEFENSE INFORMATION APPLIES
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS
(MANUFACTURERS AND NON-MANUFACTURERS)
RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RQ032: EXPORT CONTROL OF TECHNICAL DATA
This item has technical data some or all of which is subject to export-control of either the International Traffic in Arms regulations (ITAR) or the Export Administration Regulations (EAR), and cannot be exported without prior authorization from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and nationals whether located in the United States or abroad. This requirement applies equally to foreign national employees and U.S. companies and their foreign subsidiaries. DFARS 252.225-7048 is applicable to this data.
The Defense Logistics Agency (DLA) limits distribution of export-control technical data to DLA contractors that have an approved US/Canada Joint Certification Program (JCP) certification, have completed the Introduction to Proper Handling of DOD Export-Controlled Technical Data Training and the DLA Export-Controlled Technical Data Questionnaire (both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. NSN/Part Number: 4935-01-115-2750 Quantity: 3 EA Purchase Request: 7018680923QTY: 3 Delivery: 323 days ADO