ELECTRON TUBE

ELECTRON TUBE
ELECTRON TUBE
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RD002, COVERED DEFENSE INFORMATION APPLIES
Hazard Communication Standard Notice:
Effective June 1, 2015, Federal Standard No. 313-E, Material Safety Data, Transportation Data and Disposal Data for Hazardous Materials Furnished to Government Activities, establishes the requirement for preparation and submission of Safety Data Sheets (SDS) in lieu of Material Safety Data Sheets (MSDS) by suppliers who provide hazardous materials to government activities.
The Occupational Safety and Health Administration (OSHA) has modified its Hazard Communication Standard (HCS) to conform to the United Nations Globally Harmonized System of Classification and Labeling of Chemicals. As a result of this change, GSA revised Federal Standard No. 313-E requiring Safety Data Sheets for classifying chemicals and communicating the applicable information on labels.
In accordance with the revised standard after June 1, 2015:
1. Suppliers will be required to submit, to the contracting officer for review and approval prior to award, safety data sheets consistent with the requirements found at 29 C.F.R. 1910.1200 for hazardous materials delivered to the Government.
2. Suppliers will also be required to submit, to the contracting officer for review and approval prior to award, Hazardous Communication Standard (HCS) labels in accordance with 29 C.F.R. 1910.1200 requirements or current Consumer Product Safety Act (CPSA), Federal Hazardous Substance Act (FHSA) labels when subject to labeling requirements under those statutes. This product labeling is required for hazardous materials delivered to the Government.
3. Finally, suppliers must train their employees on the new safety data sheets, hazardous communication labels, and requirements of 29 C.F.R. 1910.1200.
For more information on SDS, refer to OSHAs website, available at:
https://www.osha.gov/law-regs.html
For information on 29 C.F.R. 1910.1200, refer to the below link:
https://www.osha.gov/dsg/hazcom/index.html RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
SPE7M1-27-T-1967
SECTION B
RQ002: CONFIGURATION CHANGE MANAGEMENT ENGINEERING CHANGE PROPOSAL
REQUEST FOR VARIANCE (DEVIATION OR WAIVER)
RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
RD004: Cybersecurity Maturity Model Certification (CMMC) Level 2 Self-Assessment RD004: Cybersecurity Maturity Model Certification (CMMC) Level 2 Self-Assessment SELECTED ITEM
CRITICAL APPLICATION ITEM
THOMAS ELECTRONICS, INC 4U430 P/N 10M386P43M NORTHROP GRUMMAN SYSTEMS CORPORATION 97942 P/N 645A621H01
TDP Rev B Gen 2 IAW BASIC DRAWING NR 97942 645A621 REVISION NR F DTD 09/27/2023 PART PIECE NUMBER: 645A621H01
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 7019012354 0001 EA 3.000
NSN/MATERIAL:5960012150992
DELIVERY (IN DAYS):0185
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: ORIGIN
ACCEPTANCE POINT: ORIGIN
PREP FOR DELIVERY:
SPE7M1-27-T-1967
SECTION B
PR: 7019012354 PRLI: 0001 CONT’D
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:ZZ CLNG/DRY:1 PRESV MAT:00
WRAP MAT:ZZ CUSH/DUNN MAT:ZZ CUSH/DUNN THKNESS:Z
UNIT CONT:ED OPI:M
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:36 -36 Fragile, arrow up and glass
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
PRESERVATION AND PACKAGING SHALL BE IAW THE
LATEST REVISION OF MILITARY SPECIFICATION:
MIL-DTL-75, FOR ELECTRON TUBES.
IP025: PACKAGING, MARKING, AND SHIPPING OF HAZARDOUS MATERIALS
PARCEL POST ADDRESS:
SW3211
DLA DISTRIBUTION DEPOT OKLAHOMA
3301 F AVE CEN REC BLDG 506 DR 22
TINKER AFB OK 73145-8000
US
FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE
C20 AND CONTRACT
FREIGHT SHIPPING ADDRESS:
SW3211
DLA DISTRIBUTION DEPOT OKLAHOMA
3301 F AVE CEN REC BLDG 506 DR 22
TINKER AFB OK 73145-8000
US
Need Ship Date:05/21/2027 Original Required Delivery Date:05/21/2027
SPE7M1-27-T-1967 NSN/Part Number: 5960-01-215-0992 Quantity: 3 EA Purchase Request: 7019012354QTY: 3 Delivery: 185 days ADO