EXHAUST SYSTEM, ENGINE

EXHAUST SYSTEM,ENGINE
EXHAUST SYSTEM,ENGI
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RQ002: CONFIGURATION CHANGE MANAGEMENT ENGINEERING CHANGE PROPOSAL
REQUEST FOR VARIANCE (DEVIATION OR WAIVER)
RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RT001: MEASURING AND TEST EQUIPMENT
EXCEPTION TO DRAWING 12563625 AM GENERAL, CAGE 34623'S CORRECT PART
NUMBER IS 12563625 IN LIEU OF 6000097.
Unless otherwise stated, identification marking shall be in accordance with paragraph 4.1.b(2) of MIL-STD-130N. This is in addition to any required manufacturer's logo, lot number, and material identification markings.
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
NOTE: THE CITED DRAWING IS A SOURCE CONTROLLED
DRAWING AND AS OF THE DATE OF THIS SOLICITATION
ONLY THE SOURCE(S) CITED ON THE DRAWING HAVE
BEEN APPROVED. EVEN THOUGH SOURCES AND APPROVED
PART NUMBERS ARE PROVIDED, THE ITEMS
FURNISHED MUST MEET THE REQUIREMENTS OF THE
CITED DRAWING. OFFERORS WHO ARE INTERESTED IN
QUALIFYING THEIR PRODUCT FOR PURPOSE OF FUTURE
ACQUISITION MUST CONTACT THE COGNIZANT DESIGN
ACTIVITY SPECIFIED ON THE SOURCE CONTROLLED
DRAWING.
ALSO, MAY INCLUDE ADDITIONAL APPROVED SOURCES
SPE7L5-27-T-0577
SECTION B
THAT HAVE NOT BEEN REFLECTED ON THE DRAWING AT
THIS TIME.
CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE
USED NOR INCORPORATED IN ANY ITEMS TO BE
DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION
SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT
DOES NOT ALLEVIATE ANY PRODUCT REQUIREMENTS.
SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR
APPROVAL UNLESS THEY ARE AUTHORIZED BY THE
SPECIFICATION REQUIREMENTS.
"CONTRACTOR/MANUFACTURER IS REQUIRED TO
ESTABLISH AND MAINTAIN A CALIBRATION SYSTEM THAT
MEETS THE REQUIREMENTS OF ANSI/NCSL Z540-1-1994,
AMERICAN NATIONAL STANDARD FOR CALIBRATION
CALIBRATION LABORATORIES AND MEASURING AND TEST
EQUIPMENT-GENERAL REQUIREMENTS, OR ISO 10012-1,
QUALITY ASSURANCE REQUIREMENTS FOR MEASURING
EQUIPMENTPART 1, METROLOGICAL CONFIRMATION
SYSTEM FOR MEASURING EQUIPMENT."
"FINAL INSPECTION AND ACCEPTANCE OF THE ITEM
SHALL BE AT THE ACTUAL MANUFACTURING FACILITY.
TECHNICAL INSPECTION IS REQUIRED. THE
CONTRACTOR SHALL MAKE DRAWINGS AND TECHNICAL
INFORMATION AVAILABLE TO VERIFY THAT THE ITEM
MEETS ALL TECHNICAL REQUIREMENTS.
COUNT, KIND, AND CONDITION INSPECTIONS ARE
NOT ACCEPTABLE. THIS NOTE TAKES PRECEDENCE OVER
MASTER SOLICITATION PART ONE PROVISIONS, NOTE 6,
QUOTATIONS BY NON-MANUFACTURERS (APR 1984,
DCSC 52.217-9C01). FINAL INSPECTION OF
PACKAGING, IF REQUIRED, MAY BE CONDUCTED
ELSEWHERE."
FAR 52.246-11, HIGHER LEVEL CONTRACT QUALITY
REQUIREMENTS, APPLIES/ISO 9001/ANSI/ASQC
Q 9001 APPLIES.
RD005: Cybersecurity Maturity Model Certification (CMMC) Level 2 Certified Third-Party Assessment Organization (C3PAO) RD005: Cybersecurity Maturity Model Certification (CMMC) Level 2 Certified Third-Party Assessment Organization (C3PAO)
RQ032: EXPORT CONTROL OF TECHNICAL DATA
This item has technical data some or all of which is subject to export-control of either the International Traffic in Arms regulations (ITAR) or the Export Administration Regulations (EAR), and cannot be exported without prior authorization from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and nationals whether located in the United States or abroad. This requirement applies equally to foreign national employees and U.S. companies and their foreign subsidiaries. DFARS 252.225-7048 is applicable to this data.
The Defense Logistics Agency (DLA) limits distribution of export-control technical data to DLA contractors that have an approved US/Canada Joint Certification Program (JCP) certification, have completed the Introduction to Proper Handling of DOD Export-Controlled Technical Data Training and the DLA Export-Controlled Technical Data Questionnaire (both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. NSN/Part Number: 2990-01-640-8509 Quantity: 48 EA Purchase Request: 7019020669QTY: 48 Delivery: 147 days ADO