FC1 Coupling

SOURCES SOUGHT TECHNICAL DESCRIPTION DISCLAIMER THIS SOURCES SOUGHT IS FOR INFORMATIONAL PURPOSES ONLY. THIS IS NOT A REQUEST FOR QUOTATION/PROPOSAL (RFQ/RFP). THIS SOURCES SOUGHT DOES NOT CONSTITUTE A SOLICITATION AND SHALL NOT BE CONSTRUED AS A COMMITMENT BY THE GOVERNMENT. RESPONSES IN ANY FORM ARE NOT OFFERS AND THE GOVERNMENT IS UNDER NO OBLIGATION TO AWARD A CONTRACT AS A RESULT OF THIS ANNOUNCEMENT. NO FUNDS ARE AVAILABLE TO PAY FOR PREPARATION OF RESPONSES TO THIS ANNOUNCEMENT. ANY INFORMATION SUBMITTED BY RESPONDENTS TO THIS TECHNICAL DESCRIPTION IS STRICTLY VOLUNTARY. THIS NOTICE SEEKS INFORMATION ON COMMERCIAL OFF THE SHELF ITEMS. INTRODUCTION The scope of this procurement is for the contractor to supply and install a main drive motor shaft (FC1) Coupling. Government will remove existing coupling. Contractor shall provide all labor, equipment, materials, and testing for the installation of the coupling: The FC1 Coupling connects the main drive motors to the C1 Compressor in Propulsion Wind Tunnel (PWT) for the 16T Circuit. Coupling Specifications: 1.The gear coupling must be able to transmit power from the drive shaft to the compressor shaft, must accommodate axial thermal growth in the shafts, and must allow for quick disconnect in place for uncoupling. 2.Power rating (331,000 hp at 600 rpm), torque rating (4,450,000 ft-lbs), thermal growth allowance (2 inches), decoupling time (2 hours), and that the device shall accommodate the existing spatial and fit constrains of the existing coupling. 3.The nominal shaft diameter is 27 inches and axial thermal growth is 2 inches of the shaft ends toward each other. The result of this market research will contribute to determining the method of procurement, if a requirement materializes. Based on the responses to this sources sought notice/market research this requirement may result in a single source acquisition, may be set-aside for small businesses (in full or in part), or may be procured through full and open competition. Telephone inquiries will not be accepted or acknowledged, and no feedback or evaluations will be provided to companies regarding submissions. ELIGIBILITY The applicable NAICS code for this requirement is 333613, All Other Miscellaneous Electrical Equipment and Component Manufacturing with a Small Business Size Standard of 500 employees. The Product Service Code (PSC) is N030, Miscellaneous Electrical and Electronic Components. SUBMISSION DETAILS Interested businesses should submit a brief capabilities statement package (no more than ten 8.5 x 11 inch pages, font no smaller than 10 point) demonstrating ability to provide the products listed in this Technical Description. Documentation should be in bullet format. No phone or email solicitations with regards to the status of the RFQ will be accepted prior to its release. Your capabilities statement must provide evidence of being able to supply all items identified above. Your response to this Sources Sought, including any capabilities statement, shall be electronically submitted to the Contract Specialist, Cynthia Young in either Microsoft Word or Portable Document Format (PDF), via email cynthia.young.4@us.af.mil no later than 2:00 p.m. CST on 3 July 2019 and reference this synopsis number in subject line of e-mail and on all enclosed documents. Information and materials submitted in response to this request WILL NOT be returned. DO NOT SUBMIT CLASSIFIED MATERIAL. After review of the attached Statement of Work, if your organization has the potential capacity to provide the required products/systems, please provide the following information: 1) Organization name, address, primary points of contact (POCs) and their email address, Web site address, telephone number, and type of ownership for the organization, CAGE Code, and Dun and Bradstreet DUNS #. 2) Tailored capability statements addressing the requirements of this notice, with appropriate documentation supporting claims of your firm's capability to meet our technical requirements. If you are submitting a substitute item, you must provide technical detail sufficient for AEDC to determine if your proposed item(s) will meet our need. Additionally, the submission should outline what vehicles can be utilized to obtain the items provided in this sources sought notice such as GSA (provide schedule), or any other existing contract vehicle. All data received in response to this Sources Sought that is marked or designated as corporate or proprietary will be fully protected from any release outside the Government.