FELT SHEET

FELT SHEET . RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SETFORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEBAT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECTON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFPISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATECONTROLS.
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTEDSUPPLIES
INDIVIDUAL NSN DATA . NSN 8305-00-290-5587, PGC90138 . ITEM NAME: FELT SHEET PART NUMBER: C-F-206 CAGE CODE:81348 . Shall be in accordance with (IAW) Federal Specification C-F-206H, FELT SHEET: CLOTH,FELT, WOOL, PRESSED dated 23 February2021. . Shall also be in an accordance with Federal Specification C-F-206G, FELT SHEET: CLOTH,FELT, WOOL, PRESSED dated 27 June 1989 for Tables I, II, and III ONLY. . Width: 72 inches minimum Thickness: 0.25 (1/4) inches nominal; 0.224 inches minimum to 0.276inches maximum Environmental protection: Mildew resistant C-F-206 Federal Specification Classification code: 9R4 S.A.E. J314BClassification number: F-13 ASTM (Northern Textile Association) Classification: 18R4 Wool fiber content: 75 percent minimum Tensilestrength: 75 pounds per square inch (p.s.i.) minimum Weave Type: Nonwoven Cloth Weight: 1.96 pounds per square yard minimum to 2.28pounds per square yard maximum Special Features: Roll form Fiber material: Wool basic and extraneous material basic Color: Gray both sides Procurement Group Code (PGC): 90138 Type: I (Mechanical-roll felt) Roll length: 26 yards minimum to 55 yards maximum . 9R4:Suggested service application for sound deadening, chassis strips, spacers, dust shields, pedal pads, dash liners, and formechanical purposes where abrasion and wear are not important factors. . Each roll or sheet of the finished felt shall be labeled or ticketed for fiber content in accordance with the Rules and Regulations under the Textile Fiber Products IdentificationAct. . Shall be mildew resistant per MIL-PRF-2312G, FELT, HAIR OR WOOL: MILDEW RESISTANT AND MOISTURE RESISTANT TREATEMENT FOR dated 10 October 2019 and validated through Notice 1 dated 15 August 2024. . Unit of issue is a SQUARE FOOT (SF). . TEST REPORTS ANDCOMPONENT CERTIFICATIONS IN ACCORDANCE WITH DLA TROOP SUPPORT CLOTHING & TEXTILES ADDITIONAL QUALITY ASSURANCE REQUIREMENTS,Revision 1 dated 1 August 2021 (superseding DPSCM-4155.3 dated 3 November 1997) ARE REQUIRED WITH ALL CONTRACT COMPONENTLOTS. . In lieu of the abovenamed requirement, if the total contract award does NOT exceed $100,000, the contract awardee maysubmit a Certificate of Compliance (CoC) per 3.1.3 of the DLA Troop Support Clothing and Textiles (C&T) Additional Quality Assurance Requirements (AQAR), Revision 1 dated August 2021.
Please note, however, use of the CoC in lieu of submitting the certifiedtest reports, is subject to approval by the Contracting Officer identified on the solicitation, purchase order, and/or thecontract. .
SPE1C1-26-Q-0231
SECTION B
SUPPLY/SERVICE: PGC: 90138 CONT'D
SOURCES OF COMPONENT MATERIALS SHALL BE IDENTIFIED, INCLUDING APPLICABLE SPECIFICATIONS, AND SHALL NOT BE CHANGEDTHROUGHOUT THE LIFE OF THE CONTRACT WITHOUT REQUEST AND APPROVAL BY THE DLA TROOP SUPPORT CONTRACTING OFFICER THROUGHMODIFICATION TO THE CONTRACT.
RESPONSIBILITY OF INSPECTION. THE CONTRACTOR IS RESPONSIBLE FOR THE PERFORMANCE OF ALLINSPECTION, EXAMINATION, AND TEST REQUIREMENTS SPECIFIED HEREIN AND IN THE SITED SPECIFICATIONS AND CONTRACT. THE GOVERNMENTRESERVES THE RIGHT TO PERFORM ANY OF THE INSPECTIONS, EXAMINATIONS AND TESTS AS DEEMED NECESSARY TO ENSURE SUPPLIES ANDSERVICES CONFORM TO PRESCRIBED REQUIREMENTS. . RT001: MEASURING AND TEST EQUIPMENT
. GOVERNMENT LABORATORY TESTING OF COMPONENTSFOR ACCEPTANCE PURPOSE
FOR PHYSICAL (NON-SHADE) TESTING: Only applicable if the total contract award exceeds $100,000
In lieuof the abovenamed requirement, if the total contract award does NOT exceed $100,000, the contract awardee may submit a Certificateof Compliance (CoC) per 3.1.3 of the DLA Troop Support Clothing and Textiles (C&T) Additional Quality Assurance Requirements (AQAR), Revision 1 dated August 2021. . THE VENDOR SHALL NOTIFY THE DLA Product Test Center -Analytical FOURTEEN (14) CALENDAR DAYS TOTHIRTY (30) CALENDAR DAYS IN ADVANCE OF WHEN LOTS ARE TO BE PRESENTED FOR SAMPLING AT THE ADDRESS BELOW.
THE CONTRACTOR'S APPROVEDQUALIFIED LABORATORY WILL BE REQUIRED TO FORWARD A COMPLETED TEST REPORT FOR EACH LOT OF COMPONENTS TO THE ADDRESS BELOW. THESUPPLIER'S SOURCE SAMPLING REPRESENTATIVE WILL PROVIDE THE COMPLETED DD FORM 1222 dated March 2021 TO THE LABORATORY TO BE SUBMITTED WITH THE COMPLETED TEST REPORT. TEST REPORTS SHALL NOT BE OLDER THAN NINETY (90) CALENDAR DAYS.
LOT NOTIFICATIONS AND SOURCESAMPLING DD1222s/TEST REPORTS SHALL BE FORWARDED TO: paactlab@dla.mil
SAMPLES FOR PHYSICAL TESTING WILL ONLY BE FORWARDED UPONREQUEST TO: DLA Product Test Center -Analytical 700 Robbins Avenue, BLDG 5D Philadelphia, PA 19111 EMAIL: paactlab@dla.mil
NOTE: PERMIT 45 CALENDAR DAYS . Identification of Testing Sites. Unless the contract mandates a Government laboratory be used to conducttesting, the prime contractor shall identify all testing sites that will perform any test required by the terms of the contract, including end item testing. Any laboratory proposed by the contractor is subject to the approval of the contracting officer. Testing facilities shall be subject to on-site witnessing of testing by the Government. The use of a laboratory previously approved by theGovernment is not a guarantee that testing will be performed properly, nor does it relieve a contractor from the contractualobligation to present conforming supplies accompanied by true, accurate, and valid test results.
Certification of Testing Sites.The prime contractor shall identify a technical point of contact for the testing site and provide current contact information. Theprime contractor should alert the technical point of contact that the certification process has begun. A current ISO 17025accreditation whose scope encompasses the contractual testing or equivalent will be accepted. When a testing site and its contactinformation are provided to DLA Contracting and the DLA Product Specialist, the product specialist will initiate a request for theDLA Product Test Center (DLA-PTC) to certify the lab. This request will be managed via an internal DLA Troop Support process.
Inthe absence of an appropriate ISO 17025 accreditation, the DLA-PTC will compare all required testing in the contract to thecommercial lab capability. If the testing facility is new and/or unknown to the DLA-PTC, a lab certification survey (DLA Form 6005)will be provided for submission.
If the DLA-PTC has a lab survey on file that is less than 3 years old, that survey will be usedfor the initial NSN/Part Number: 8305-00-290-5587 Quantity: 50,000 SF Purchase Request: 7016494185QTY: 50000 Delivery: 120 days ADO