FLAG, NATIONAL

FLAGS NATIONAL
"FLAG, NATIONAL, TYPE II "
SPAIN
RAYON BANNER CLOTH
"HOIST: 2 FT. 10 IN., FLY: 4 FT. 2 IN. "
.
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITYREQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITYREQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THEREVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
A-A-52094B Thread, Cottondated 01 May 2019 No Additional Information (ref. T1481) ADDITIONAL INFORMATION FOR A-A-50196:
(NO CURRENT CHANGES TOA-A-50196B) ADDITIONAL INFORMATION FOR MIL-PRF-20696: . NO ADDITIONAL INFORMATION FOLLOWS. . ADDITIONAL INFORMATION FORCCC-C-430: .
A-A-50145 HAS BEEN AUTHORIZED FOR USE IN PREFERENCE TO CCC-C-430 FOR THE TYPE II CLOTH ADDITIONAL INFORMATION FORA-A-50145: . A-A-50145 CLOTH, SHEETING, COTTON,
. AND POLYESTER/COTTON, WHITE INTERIM SPECIFICATIONCHANGES TO A-A-50145: PAGE 1, PARA. 1.1, LINE 11 AFTER "122 COUNT:ADD "(UNDYED)" PAGE 2, TABLE I, UNDER TYPE I AND TYPE II, ACROSSFROM SHRINKAGE: DELETE "2.0" AND SUBSTITUTE "3.0" IN ALL FOUR LOCATIONS. PAGE 2, TABLE I, UNDER TYPE II, AFTER "122 COUNT": ADD"(UNDYED)" PAGE 3, PARAGRAPH 3.1: DELETE AND SUBSTITUTE: "3.1 CERTIFICATION. THE CONTRACTOR SHALL CERTIFY, AND MAINTAINSUBSTANTIATING EVIDENCE THAT THE PRODUCT OFFERED MEETS THE SALIENT CHARACT- ERISTICS AND REQUIREMENTS OF THIS COMMERCIAL ITEMDESCRIPTION, AND THAT THE PRODUCT CONFORMS TO THE PRODUCER'S OWN DRAWINGS, SPECIFICATIONS, STANDARDS AND QUALITY ASSURANCEPRACTICES. THE GOVERNMENT RESERVES THE RIGHT TO REQUIRE PROOF OF SUCH CONFORMANCE PRIOR TO FIRST DELIVERY AND THEREAFTER AS MAY BEOTHERWISE PROVIDED FOR UNDER THE PROVISIONS OF THE CONTRACT. . 3.2 VISUAL EXAMINATION. LOTS OF CLOTH SHALL BE IN ACCORDANCE WITHMIL-STD-105. THE INSPECTION LEVEL SHALL BE II. THE LOT SIZE SHALL BE EXPRESSED IN UNITS OF YARDS. THE SAMPLE SIZE SHALL BE ONELINEAR YARD. THE CLOTH SHALL BE EXAMINED ON THE FACE SIDE FOR THE FOLLOWING
SPE1C1-26-Q-0463
SECTION B
SUPPLY/SERVICE: PGC: 31242 CONT'D
DEFECTS: HOLE, TEAR, RUN OR DROPPED STITCH,
END OUT,MEND, THIN OR UNEVEN AREA, SLUB,
SLUG OR GOUT, PERMANENT CREASE IN CLOTH, SHADE
BAR, STREAK, SPOT OR STAIN, WEIGHT NOTAS
SPECIFIED.
.
3.3 LENGTH EXAMINATION. DURING THE YARD-BY-YARD
EXAMINATION, EACH ROLL IN THE SAMPLE SHALL BE
EXAMINED FOR LENGTHAND WEIGHT. ANY LENGTH FOUND
TO BE LESS THAN THE MINIMUM SPECIFIED OR MORE
THAN 2 YARDS LESS THAN THE LENGTH MARKED ON THE
ROLLTICKET SHALL BE CONSIDERED A LENGTH DEFECT.
IF THE TOTAL OF THE ACTUAL LENGTHS OF THE ROLLS
IS LESS THAN THE TOTAL OF THE LENGTHSMARKED ON
THE ROLL TICKETS, THE LOT SHALL BE REJECTED."
PAGE 4, PARA. 5.4: DELETE AND SUBSTITUTE THE
FOLLOWING: :5.4 SUPERSESSIONDATA. THE TYPES
AND STYLES COVERED BY THIS COMMERCIAL ITEM
DESCRIPTION REPLACE (IN PART) ITEMS COVERED
BY CCC-C-430 AS INDICATEDBELOW:
CID A-A-50145 CCC-C-430
TYPE I, 140 COUNT TYPE II, STYLE A
TYPE I, 128 COUNT TYPE II, STYLE B
TYPE II,122 COUNT TYPE II, STYLE G
(UNDYED) (BLEACHED ONLY)
TYPE II, 177 COUNT TYPE II, STYLE D
. (BLEACHED ONLY)".
ADDITIONAL INFORMATION FOR MIL-C-606:
.
NO ADDITIONAL INFORMATION FOLLOWS.
.
ADDITIONAL INFORMATION FORMIL-T-713:
.
NO ADDITIONAL INFORMATION FOLLOWS.
.
ADDITIONAL INFORMATION FOR ML-F-2310:
.
NO ADDITIONAL INFORMATIONFOLLOWS.
.
ADDITIONAL INFORMATION FOR MIL-C-3636:
.
WITH THE FOLLOWING INTERIM CHANGES:
PAGE 3, PARA. 3.3.3 DELETE IN ITSENTIRETY
AND SUBSTITUTE "3.3.3 WOOD-WOOD FOR THE
MOULDS SHALL BE ANY CLEAR, STRAIGHT GRAIN
HARDWOOD WHICH IS FREE FROM CHECKS OROTHER
DEFECTS WHICH MIGHT AFFECT SERVICEABILITY."
PARA.3.4 DELETE "(SEE FIGURE 1)"
PAGE 5, PARA.3.6.2.1 DELETE IN ITS ENTIRETY
ANDSUBSTITUTE "3.6.2.1 MOULD-THE MOULD
SHALL BE TURNED FROM WOOD SPECIFIED IN 3.3.3
OR MOLDED FROM ANY SUITABLE TYPE OF HIGH
IMPACTMOLDING PLASTIC. THE MOULD SHALL BE
COMPLETELY COVERED WITH BRAID. THE SHAPE OF
THE MOULD SHALL BE AT THE OPTION OFTHE
MANUFACTURER PROVIDED IT MEETS THE FOLLOWING
REQUIREMENTS.
TABLE TEXT, OVERALL LENGTH 3-5/8 ( OR 1/4
) INCH --MAXIMUMDIAMETER 1-1/8 INCH
MINIMUM DIAMETER 1/2 INCH. THE WIDEST PORTION
OF THE MOULD SHALL BE AT THE BOTTOM (FRINGED
END) OF THEMOULD."
PAGE 18, FIGURE 1 DELETE ALL DIMENSIONS FROM
THE LINE DRAWING.
INTERIM CHANGES TO MIL-C-3636C:
.
PAGE 5, PARA 3.6.1 CORDS. ADD THE FOLLOWING
AT THE END OF THE SENTENCE: A 550 DENIER
25 DENIER ACETATE MAY BE USED IN LIEU OF 300
DENIER RAYON.
.
PAGE 5,PARA 3.6.2 TASSELS. ADD THE FOLLOWING
AT THE END OF THE SENTENCE: A 550 DENIER
25 DENIER ACETATE MAY BE USED IN LIEU OF300
DENIER RAYON.
.
PAGE 5, PARA 3.6.2.2 FRINGE OR SKIRT BULLION.
SPE1C1-26-Q-0463
SECTION B
SUPPLY/SERVICE: PGC: 31242 CONT'D
ADD THE FOLLOWING AT THE END OF THE SENTENCE:
A 550 DENIER 25DENIER ACETATE MAY BE USED
IN LIEU OF 300 DENIER RAYON.
.
PAGE 6, PARA 3.6.2.3 CROUSE CORD. ADD THE
FOLLOWING AT THE END OF THESENTENCE: A 550
DENIER 25 DENIER ACETATE MAY BE USED IN
LIEU OF 300 DENIER.
.
PAGE 11, PARA. 4.3.3.1.3, LINE 6, DELETE
"4.3.3.1.1 I 2.5 6.5" AND SUBSTITUTE
"4.3.3.1.1 I 1.5 4.0"
LINE 7, DELETE "4.3.3.1.2 S-3 ONE CLASS 4.0"
AND SUBSTITUTE"4.3.3.1.2 S-3 ONE CLASS 2.5".
.
BAR CODE LABEL/TAG FOR MIL-C-3636. EACH ITEM
SHALL BE INDIVIDUALLY BAR CODED. THE BARCODE
ELEMENT SHALL BE A 13 DIGIT NATIONAL STOCK
NUMBER (NSN). THE BAR CODE FOR NSN SHALL BE
A MEDIUM TO HIGH DENSITY, CLEARLYLEGIBLE AND
READABLE BY SCANNER, AND SHALL BE LOCATED SO
THAT THEY ARE COMPLETELY VISIBLE ON THE ITEM
WHEN PACKAGED AS SPECIFIED.ATTACHMENT OF THE
LABEL SHALL CAUSE NO DAMAGE TO THE ITEM.
THE LABEL SHALL BE POSITIONED INSIDE THE
PLASTIC BAG AND SHALL BE TYPEVII OR
MIL-DTL-32075.
BAR CODE DEFECTS:
-BAR CODE OMITTED OR NOT READABLE BY SCANNER
MINOR.
-HUMAN READABLE INTERPRETATION (HRI)OMITTED
MINOR.
HUMAN READABLE INTERPRETATION (HRI) OMITTED
MINOR.
NOT VISIBLE ON FOLDED, PACKAGED ITEM-MINOR.
CAUSE DAMAGE TO THEITEM-MAJOR.
.
ADDITIONAL INFORMATION FOR MIL-R-17343D:
.
MIL-R-17343D ROPE, NYLON, 6/2/69, AM 1,
. 8/9/71. NOT. 1,VALIDATION 05 MAY 1989.
.
ADDITIONAL INFORMATION FOR MIL-C-22775:
.
SHRINKAGE REQUIREMENTS UNDER MIL-C-22775;
SHRINKAGE SHALL NOTEXCEED 5.0 PERCENT
MAX. IN THE WARP DIRECTION AND 3.2 PERCENT
IN THE FILLING DIRECTION.
.
PAGE 2.
2.2, DELETE AND SUBSTITUTE:
"2.2NON-GOVERNMENT PUBLICATIONS. THE FOLLOWING
DOCUMENTS FORM A PART OF THIS DOCUMENT TO
THE EXTENT SPECIFIED HEREIN. UNLESSOTHERWISE
SPECIFIED, THE ISSUES OF THESE DOCUMENTS ARE
THOSE CITED IN THE SOLICITATION OR CONTRACT".
AATCC
AATCC 8 COLORFASTNESS TOCROCKING: AATCC CROCK
METER METHOD
AATCC 16E COLORFASTNESS TO LIGHT (WATER-COOLED
XENOR-ARC CONTINUOUS LIGHT)
AATCC 20A FIBERANALYSIS: QUANTITATIVE
AATCC 61 COLORFASTNESS TO LAUNDERING, HOME AND
COMMERCIAL: ACCELERATED
AATCC 81 PH OF WATER-EXTRACT FROM WETPROCESSED
TEXTILES
AATCC 106 COLORFASTNESS TO WATER: SEA
(COPIES OF THESE DOCUMENTS ARE AVAILABLE ONLINE
AT HTTP://WWW.AATCC.ORG ORFROM THE AATCC,P.O.
BOX 12215, RESEARCH TRIANGLE PARK, NC 27709.)
ASTM INTERNATIONAL
ASTM D737 TEST METHOD FOR AIR PERMEABILITYOF
TEXTILE FABRICS
ASTM D 3775 STANDARD TEST METHOD FOR FABRIC
COUNT OF WOVEN FABRIC
ASTM D3776 STANDARD TEST METHODS FOR MASSPER
UNIT AREA (WEIGHT OF FABRIC)
SPE1C1-26-Q-0463
SECTION B
SUPPLY/SERVICE: PGC: 31242 CONT'D
ASTM D5034 STANDARD TEST METHOD FOR BREAKING
STRENGTH AND ELONGATION OF TEXTILE FABRICS(GRAB
TEST)
(COPIES OF THESE DOCUMENTS ARE AVAILABLE ONLINE
AT HTTP://WWW.ASTM.ORG OR ASTM INTERNATIONAL,100
BARR HARBOR DRIVE, WEST CONSHOHOCKEN, PA 19428
2959.)
PAGE 3.
3.4.2, DELETE AND SUBSTITUTE:
"3.4.2 COLORFASTNESS. THE FINISHED CLOTH SHALL
SHOW FASTNESSTO WET CROCKING, DRY CROCKING,
LAUNDERING, SEAWATER, AND LIGHT (40 AATCC FADING
UNITS) EQUAL TO OR BETTER THAN THE STANDARD
SAMPLEWHEN TESTED AS SPECIFIED IN 4.5. WHEN NO
STANDARD SAMPLE IS AVAILABLE, THE FINISHED CLOTH
SHALL SHOW A MINIMUM OF "GOOD" OR RATINGOF "3"
TO THE AFOREMENTIONED COLORFASTNESS REQUIREMENT.
3.5., TABLE I, DELETE SUBSTITUTE:
TABLE IPHYSICALREQUIREMENTS
WEIGHT,OZ/SQ.YD.MIN. YARNS(PER INCH)MIN. BREAKING
STRENGTH (LBS.) MIN. AIR PERMEABILITY (FT3/
MIN / FT2) MIN. WEAVE
4.5 WARP 28 FILLING 29 WARP 95 FILLING 97 250
PLAIN
PAGE 4.
3.5.2., DELETE AND SUBSTITUTE:
"3.5.2. DIMENSIONAL STABILITY.THE FINISHED CLOTH
SHALL NOT SHRINK OR ELONGATE MORE THAN + 4% IN
BOTH THE WARP OR FILLING DIRECTION WHEN TESTED
AS SPECIFIED IN 4.5."
PAGE8.
4.5, DELETE AND SUBSTITUTE:
"4.5 TESTING OF THE END ITEM. THE METHODS OF
TESTING LISTED IN TABLE II SHALL BE FOLLOWED
TO VERIFYTHE REQUIREMENTS IN SECTION 3. THE
PHYSICAL AND CHEMICAL VALUES SPECIFIED IN
SECTION 3 APPLY TO THE AVERAGE OF THE
DETERMINATIONSMADE ON THE SAMPLE UNIT FOR TEST
PURPOSES AS SPECIFIED IN THE APPLICABLE TEST
METHODS. ALL TEST REPORTS SHALL CONTAIN
INDIVIDUALVALUES UTILIZED IN EXPRESSING THE
FINAL RESULTS. THE SAMPLE UNIT FOR TEST
PURPOSES SHALL BE 3-1/2 CONTINUES YARDS FULL
WIDTH OF THEFINISHED CLOTH. THE LOT SIZE SHALL
BE EXPRESSED IN UNITS OF ONE YARD. THE LOT SHALL
BE UNACCEPTABLE IF ONE OR MORE OF THESAMPLE
UNITS FAIL TO MEET ANY OF THE TEST REQUIREMENTS
SPECIFIED. THE SAMPLE SIZE SHALL BE IN ACCORDANCE
WITH THE FOLLOWING.
LOTSIZE (YARDS) SAMPLE SIZE (UNITS)
800 OR LESS 2
801 UP TO AND INCLUDING 22,000 3
22,001 AND OVER 5
TABLE II TEST METHODS
CHARACTERISTIC REQUIREMENT PARA. TEST METHOD
ACRYLIC FIBER
IDENTIFICATION OF FIBER 3.3.1AATCC 20A
LUSTER OF FIBER 3.3.1 VISUAL 1
QUALITY,DENIER,STAPLE LENGTH 3.3.1 VISUAL 1
YARN PLY 3.3.2 VISUAL 1
WEIGHT TABLE I ASTM D3776,OPTION C
YARNS PER INCH TABLE I ASTM D3775
BREAKING STRENGTH TABLE IASTM D5034
AIR PERMEABILITY TABLE I ASTM D737
WEAVE TABLE I VISUAL 1
DIMENSIONAL STABILITY(AFTER 1 CYCLE) 3.5.2AATCC
96, TEST VC, D 2
NON-FIBROUS 3.7 AATCC 20A
COLORFASTNESS TO:
CORCKING, DRY OR WET 3.4.2 AATCC 8
LAUNDERING 3.4.2 AATCC 61, TEST 3A 3
SEA WATER 3.4.2 AATCC 106
LIGHT (40 AATCC FACING UNITS) 3.4.2 AATCC 16E
PH 3.10 AATCC 81
1 A VISUAL COMPARISON WITH THE STANDARD SAMPLE
SHALL BE MADE TO DETERMINE COMPLIANCE. ONE
DETERMINATIONSHALL BE MADE FROM EACH SAMPLE
SPE1C1-26-Q-0463
SECTION B
SUPPLY/SERVICE: PGC: 31242 CONT'D
UNIT AND THE RESULTS REPORTED AS "PASS" OR "FAIL".
2 EXCEPT THE SAMPLES SHALL NOT BE SUBJECTEDTO
RESTORATION FORCES.
3 ONLY THE STAINS ON THE ACRYLIC FIBER SHALL BE
EVALUATED.
.
ADDITIONAL INFORMATION FORMIL-L-40051:
.
INTERIM CHANGES TO MIL-L-40051E:
PAGE 1...(PARA. I.2 )..ACROSS FROM TYPE II:
DELETE "3.1" AND SUBSTITUTE "3.0"
PAGE3...(PARA 3.5 )..DELETE "3.1" AND
SUBSTITUTE "3.0"
PAGE 4, PARA. 3.15: DELETE IN ITS ENTIRETY
PAGE 8, TABLE II: END ITEM TESTS:DELETE
"OIL ABSORPTION RESISTANCE (TREATMENT A)"
PAGE 7..(PARA 4.4.3)..UNDER THICKNESS, ACROSS
FORM TYPE II: DELETE "3.1" ANDSUBSTITUTE "3.0"
PAGE 11, PARA 4.5.3, OIL ABSORPTION: DELETE IN
ITS ENTIRETY.
PAGE 12, PARA 6.7 MINERAL OIL: DELETE INITS
ENTIRETY.
.
LIST OF APPROVED WATER RESISTANT COMPOUNDS FOR
GLOVES, MEN'S AND WOMEN'S, LIGHT DUTY,
MIL-G-822; GLOVES, MEN'S ANDWOMEN'S,
LEATHER, LIGHT DUTY, A-A-52055; GLOVES,
MEN'S AND WOMEN'S, INTERMEDIATE COLD/WET,
MIL-G-44419:
.
WATER RESISTANTCOMPOUNDS:
.
FC-236 A/B A TWO PART COMBINATION WATER AND
. OIL REPELLENT CHEMICAL FOR LEATHER
. PART A IS A WATERSOLUBLE FLUOROCHEMICAL
. PART B IS A FLUOROCHEMICAL RESIN EMULSION
. EMPLOYING MIBK AS A CARRIERSOLVENT
.
FC-3560/FC-3567 A TWO PART COMBINATION WATER
. AND OIL REPELLENT CHEMICAL FOR
.LEATHER
. FC-3560 IS A WATER SOLUBLE FLUOROCHEMICAL
. FC-3567 IS A FLUOROCHEMICAL RESIN
. EMULSION EMPLOYING ANON-FLAMMABLE
. EMULSIFIER (1%) CONTAINING NO METHYL
. ISOBUTYL KETONE
.
NOTE: MIBK HAS BEEN SHOWN TO BE ARESPIRATORY
IRRITANT AND CARRIES AN OSHA STANDARD FOR AIR OF
100 PPM, TIME WEIGHTED AVERAGE (TWA). CARE MUST
BE TAKEN BY LEATHERPROCESSORS TO ADHERE TO
THIS STANDARD WHEN USING FC-236 A/B.
.
SUPPLIER FOR THE ABOVE COMPOUNDS 3-M COMPANY.
.
ADDITIONALINFORMATION FOR MIL-T-43566:
STANDARD SAMPLE FOR TAN SHADE 380, TYPE I, CLASS 3 FABRIC IS IDENDITIED
AS ROLL #3509, REFERENCED FORSHADE, APPEARANCE AND
COLORFASTNESS.
STANDARD SAMPLE FOR CAMOUFLAGE GREEN 483, TYPE I, CLASS 3 IS IDENTIFIED
AS ROLL #3941,REFERENCED FOR SHADE, APPEARANCE AND COLORFASTNESS.
INTERIM STANDARD SAMPLE FOR FOLIAGE GREEN 504 IS MIL-C-44436, ROLL #3729
(THEFOLIAGE GREEN 504 AREA OF THE PATTERN), AND REFERENCED FOR SHADE
ONLY. FOLIAGE GREEN 504 IS TO BE USED AS
SPECIFIED BY CONTRACT.THIS APPLIES TO TYPE I, CLASS 3.
WHEN USING THIS TAPE AS AN END ITEM COMPONENT, ANY REFERENCE TO OLIVE
DRAB OR OLIVE GREEN SHOULDBE DELETED FROM THE END ITEM SPECIFICATION
AND REPLACED WITH CAMOUFLAGE GREEN 483 OR
FOLIAGE GREEN 504.
INTERIM CHANGES TOMIL-T-43566C:
PAGE 1, PARA. 1.2:
"CLASS 4" IDENTIFIER, DELETE AND SUBSTITUTE: "CLASS 4 DYED, WATER
REPELLENT, MILDEW RESISTANT.DELETE "CLASS 1A" IN ITS ENTIRETY. AT
END, ADD "1/ CLASS 1A HAS BEEN REPLACED WITH CLASS 1B."
SPE1C1-26-Q-0463
SECTION B
SUPPLY/SERVICE: PGC: 31242 CONT'D
PAGE 7, PARA. 3.5.1, AFTER "CLASS1," DELETE "1A,"
PAGE 8:
PARA. 3.7.1, LINE 1, AFTER "CLASSES", DELETE "1A" IN BOTH PLACES.
PARA 3.7.2, DELETE IN IT'S ENTIRETY, AND SUB, "PARA, 3.7.2 MILDEW
RESISTANCE A CERTIFICATE OF COMPLIANCE WILL BE ACCEPTED WHICH CERTIFIES
THAT CLASS 1B, AND CLASS 4 GREENSHADE TAPES SHALL RETAIN A 75% BREAKING
STRENGTH AFTER 12 WEEKS EXPOSURE INITIALLY AND AFTER LEACHING WHEN
EVALUATED AS SPECIFIED IN PARA. 4.5.2
PAGE 9:
PARA 3.7.2.1, DELETE IN ITS ENTIRETY.
PARA. 3.7.2.2, DELETE IN ITS ENTIRETY.
PARA. 3.8, AFTER "CLASSES" DELETE "1A".
PAGE 11, PARA. 4.4.2.1 YARD-BY-YARD EXAMINATION:
LINE 11, DELETE "0.40" AND SUBSTITUTE "0.25".
LINE 12, DELETE "1.50" ANDSUBSTITUTE "1.0".
LINE 13, DELETE "0.65" AND SUBSTITUTE "0.40".
LINE 14, DELETE "2.50" AND SUBSTITUTE "1.5".
PAGE 15, TABLEV:
DELETE "MILDEW INHIBITORS" AND SUB "MILDEW RESISTANCE"
UNDER REQUIREMENT REFERENCE, ACROSS FROM CLASSES 1B AND 4 DELETE
"3.7.2.1" AND SUB "3.7.2", UNDER TEST METHOD DELETE"2060 5/" AND SUB "
AATCC TEST METHOD 30, TEST 1 5/, 5A/
UNDER LINE CLASSES 1B AND 4DELETE THE NEXT 5 LINES ACROSS THE TABLE,
AND SUB" LEACHING RESISTANCE, UNDER REFERENCE PARA, ADD"3.7.1 UNDER TEST
METHOD ADD" PARA4.4.2"
UNDER "WATER REPELLENCY" AND "PH", AFTER "CLASSES", DELETE "1A" IN BOTH
PLACES.
PAGE 16, FOOTNOTE "5/", DELETE IN ITSENTIRETY AND SUBSTITUTE:
"5/ A MINIMUM OF 5 SPECIMENS SHALL BE TESTED THE SOIL SHALL BE MADE OF
AN EQUAL BLEND OF GOOD TOPSOIL, WELL ROTTED AND SHREDDED
MANURE AND COURSE SAND." ADD, "5A/AATCC30, TEST III MAY BE USED AS AN
ALTERNATE METHOD WITH TECHNICAL APPROVAL FROM THE PROCURING AGENCY."
PAGE 17
AFTER PARA 4.5.1, ADD A NEW PARAGRAPH "4.5.2 LEACHING RESISTANCE.
SPECIMENS TO BE TESTED FORMILDEW AND ROT RESISTANCE SHALL BE SUBMERGED
IN A SUITABLE TANK CONTAINING WATER AT A TEMP OF 80 DEGREES F TO 85
DEGREES F ANDALLOWED TO REMAIN SUBMERGED FOR A PERIOD OF 24 HOURS.
WATER FLOW THROUGH A TUBE INTO A TANK IS ADJUSTED TO ENSURE ACOMPLETED
CHANGE OF WATER NO LESS THAN THREE TIMES IN 24 HOURS. THE PH AND TEMP
OF THE WATER IS RECORDED AND INCLUDED IN THEREPORTS IS RECORDED AND
INCLUDED IN THE REPORT OF THE RESULTS."
PAGE 18, 6.6 COLOR. ADD INTERIM STANDARD SAMPLE FOR FOLIAGE GREEN504 IS
IDENTIFIED AS ROLL #3721 (THE FOLIAGE GREEN 502 AREA OF THE PATTERN),
AND REFERENCED FOR SHADE ONLY. FOLIAGE GREEN 504 IS TOBE USED AS
SPECIFIED BY CONTRACT.
(ref. T1518 May 18, 2006)
APPROVED AQUEOUS MILDEW TREATMENTS FOR MIL-W-43638 WEBBING, TEXTILE,WOVEN FOR TENT FRAMING, MIL-W-5665,WEBBING, TEXTILE, COTTON WARP, MIL-W-530, WEBBING, TEXTILE, COTTON GENERAL PURPOSE, NATURAL OR IN COLORS, AND MIL-T-43566, TAPE, TEXTILE, COTTON OR POLYESTER, GENERAL PURPOSE, NATURAL OR IN COLORS, JJ-W-155, WEBBING,TEXTILE, (COTTON, ELASTIC) . PRODUCT SUPPLIER CUNILATE 2002 MORTON INTERNATIONAL, INC
. 150 ANDOVER STREET
. DANVERS, MA. 01923
. TEL: (508-774-3100)
ACCEPTABLE ALTERNATEMILDEW TREATMENT FOR 2,2' METHYLENE-BIS-(4-CHLOROPHENOL)
1. WHEN A SPECIFICATION SPECIFIES "2,2' METHYLENE-BIS-(4- CHLOROPHENOL)"MILDEW RESISTANT TREATMENT FOR COTTON TEXTILE MATERIALS, "RO-59"
SPE1C1-26-Q-0463
SECTION B
SUPPLY/SERVICE: PGC: 31242 CONT'D
IS APPROVED AS AN ALTERNATIVE TREATMENT AND IS
AUTHORIZED FOR USE.THIS CHANGE APPLIES TO
PENDING AND FUTURE CONTRACTS USING TEXTILE
MATERIALS THAT SPECIFY THE SUBJECT MILDEW
RESISTANT TREATMENT.
2. THE PRODUCT MAY BE OBTAINED FROM:
RO-59 INC.
1 CABOT PL #3
STOUGHTON, MA 02072
TELEPHONE (781) 264-1213
POC: MR. RONNIE BENDER
3. THE TEXTILE MATERIALS TREATED WITH RO-59
MILDEW INHIBITOR TREATMENT SHALL BE TESTED IN
ACCORDANCE WITH AATCC TEST METHOD
30 -ANTIFUNGAL ACTIVITY, ASSESSMENT ON TEXTILE
MATERIALS: MILDEW AND ROT RESISTANCE OF TEXTILE
MATERIALS, TEST III. THE TREATEDMATERIAL SHALL
NOT EXHIBIT "MACROSCOPIC GROWTH
(VISIBLE TO THE EYE)".
ADDITIONAL INFORMATION FOR FED-STD-191:
FED-STD-191A NOTICE7, DATED AUGUST 9, 2000 IS HEREBY INACTIVE FOR NEW
DESIGN. WHEN NOT USING FED-STD-191, SEE INTERIM CHANGES TO ENDITEM
SPECIFICATION FOR REPLACEMENT ASTM.
INTERIM CHANGES TO FED-STD-191A:
TEST METHOD 5202, PARA. 5.3, DELETE FIRST SENTENCE ANDSUBSTITUTE: "THE
SPECIMEN SHALL BE CLAMPED FIRMLY, WITH ONE END FLUSH WITH THE OUTER EDGE
OF THE VISE, SUCH THAT ONE INCH OFSPECIMEN LIES WITHIN THE CLAMP AND
ONE INCH OF THE SPECIMEN EXTENDS BEYOND THE CENTER OF ROTATION (FACE OF
THE VISE), AND WITH THELONG EDGE PARALLEL TO THE FACE OF THE DIAL
PLATE".
TEST METHOD 5309.1 ABRASION RESISTANT OF TEXTILE WEBBING. PAGE 1,PARA
4.1.2,LINE 4: DELETE "B-97" AND SUBSTITUTE "B-91".
THE FOLLOWING METHODS ARE IDENTIFIED AS SPECIFYING OZONEDEPLETING
SUBSTANCES: 1100, 1200, 1240, 1400, 1410, 1500, 1510,1520,1530, 1540,
AND 1550. PARA 5.1 OF THESE TEST METHODS REQUIRETHE USE OF 1,1,1
TRICHLOROETHANE, ALCOHOL OR ETHER. 1,1,1-TRICHLORETHANE IS AN OZONE
DEPLETING SUBSTANCE (METHYL CHLOROFORM) ANDIS THEREFORE PROHIBITED.
THE USE OF EITHER ALCOHOL OR ETHER IS REQUIRED WHEN THESE METHODS ARE IN
BASIC OR ANY REFERENCEDDOCUMENT.
METHOD 5202, STIFFNESS OF CLOTH, DIRECTIONAL; CANTILEVER BENDING METHOD.
PAGE 2, PARA. 5.3 DELETE FIRST SENTENCE ANDSUBSTITUTE WITH THE
FOLLOWING: "THE SPECIMEN SHALL BE CLAMPED FIRMLY, WITH 1 END FLUSH WITH
THE OUTER EDGE OF THE VISE, SUCH THAT 1" OF THE SPECIMEN LIES WITHIN THE
CLAMP AND 1" OF THE SPECIMEN EXTENDS BEYOND THE CENTER OF ROTATION
(INNER FACE OF THE VISE) ANDWITH THE LONG EDGE PARALLEL TO THE FACE OF
THE DIAL PLATE."
METHOD 5556.1, MOBILE LAUNDRY NSN/Part Number: 8345-00-245-2749 Quantity: 60 EA Purchase Request: 7017645548QTY: 60 Delivery: 120 days ADO