FORMER, AIRCRAFT

FORMER,AIRCRAFT
FORMER,AIRCRAFT
DWG: 35-10701 SHEET 1, DASH NO: -2220; ENGINEERING NOTES: 1-10 BAC 5300,
USE REVISION "M" PER ENGINEERING
BAC 5300-1, USE REVISION "F" PER ENGINEERING
BAC 5300-2, USE REVISION "G" PER ENGINEERING BAC 5307, DRAWING REVISION
T USED PER ENGINEERING
ENGINEERING NOTES:
1. PART MARKING PER MIL-STD-130, METHOD PER THE DRAWING REQUIREMENTS AND
BAC 5307. MARKING MUST INCLUDE NATIONAL STOCK NUMBER, PART NUMBER,
CURRENT DESIGN AUTHORITY CODE (98748),ACTUAL MANUFACTURER'S CAGE CODE
(-----), DATE OF MANUFACTURE, AND "FOR MILITARY USE ONLY". PARTS WILL
NOT BE MARKED WITH THE ORIGINAL DESIGN AUTHORITY (BOEING) CAGE CODE.
2. ALL SPECIAL PROCESSES INDENTIFIED BY 424 SCMS IN DRAWING 20145214
SHALL BE PERFORMED BY ORGANIZATIONS MAINTAINING NADCAP CERTIFICATION FOR
THE RELEVANT SPECIAL PROCESS. ONLY THOSE PROCESSES HIGHLIGHTED IN YELLOW
IN DRAWING 20145214 ARE IDENTIFIED BY 424 SCMS AS REQUIRING NADCAP
CERTIFIED PROCESSORS.
3. DELETE REFERENCE TO D2-5000 AND BAC 5005.
4. DIMENSIONS AND TOLERANCES PER ASME Y14.5 IN LIEU OF MIL-STD-8.
5. USE CRES SHEET COND A SAE AMS 5528 IN LIEU OF MIL-S-25043.
6. FINISH CODE F-8.05 DEFINED: APPLY NO FINISH.
7. HEAT TREAT STEEL PER SAE AMS-H-6875, CLASS A, SAE AMS 2759 AND SAE
AMS 2759/1 IN LIEU OF MIL-H-6875, BAC 5601, AND BAC 5617.
8. DELETE REFERENCE TO WORDS #CONTROLLED BY BOEING MASTER TOOLS#.
9. PART TO BE FURNISHED WITHOUT FASTENER HOLES EXCEPT THOSE REQUIRED FOR
ASSEMBLY / MANUFACTURE.
10.. WHEN CHECKED BELOW OR LISTED IN THESE NOTES, DEFINITIONS
APPLICABLE TO THIS PRODUCT ARE OR HAVE:
(A) ENGINEERING CRITICAL IN APPLICATION: AN ITEM, WHICH REQUIRES SPECIAL
MANUFACTURING PROCESSES, CONTROLS, AND TESTING OF MATERIAL OR END ITEMS.
BECAUSE OF ITS USE OR APPLICATION, FAILURE TO MAINTAIN THE HIGHEST
RELIABILITY OF SUCH AN ITEM COULD BE CATASTROPHIC RESULTING IN LOSS OF
LIFE OR SERIOUS INJURY, LOSS OF A WEAPON SYSTEM OR EXTENSIVE SECONDARY
DAMAGE, WITH DIRECT IMPACT ON THE CAPABILITY TO RESPOND TO A NATIONAL
EMERGENCY OR TO ACHIEVE WARTIME SUSTAINABILITY.
(B) CRITICAL CHARACTERISTICS: CHARACTERISTICS WHICH, WHEN DEFECTIVE, ARE
LIKELY TO RESULT IN HAZARDOUS OR UNSAFE CONDITIONS FOR INDIVIDUALS
USING, MAINTAINING OR DEPENDING UPON THE PRODUCT; OR, ARE LIKELY TO
PREVENT PERFORMANCE OF THE TACTICAL FUNCTION OF A MAJOR END ITEM SUCH AS
AN AIRCRAFT, MISSILE, SPACE VEHICLE, ENGINE OR A MAJOR PART THEREOF.
(DERIVED FROM MIL-STD-1916).
(C) MAJOR CHARACTERISTICS: CHARACTERISTICS (OTHER THAN CRITICAL OR
MINOR) WHICH, WHEN DEFECTIVE, ARE LIKELY TO RESULT IN FAILURE OR TO
REDUCE THE USABILITY OF THE PRODUCT OR A MAJOR END ITEM FOR ITS INTENDED
PURPOSE. (DERIVED FROM MIL-STD-1916).
(D) MINOR CHARACTERISTICS: ALL CHARACTERISTICS NOT DESIGNATED AS
CRITICAL OR MAJOR BUT FOR WHICH FULL CONFORMITY IS REQUIRED.
(E) COMPLEX: ITEMS HAVING QUALITY CHARACTERISTICS NOT WHOLLY VISIBLE
(HIDDEN CHARACTERISTICS), IN THE END PRODUCT FOR WHICH CONTRACTUAL
CONFORMANCE MUST BE ESTABLISHED PROGRESSIVELY THROUGH PRECISE
MEASUREMENTS, TESTS OR CONTROLS APPLIED DURING PURCHASING,
MANUFACTURING, PERFORMANCE, ASSEMBLY AND FUNCTIONAL OPERATION EITHER AS
AN INDIVIDUAL ITEM OR IN CONJUNCTION WITH OTHER ITEMS [FAR SUBPART
46.203(B)].
(F) COMMERCIAL: DESCRIBED IN COMMERCIAL CATALOGS, DRAWINGS OR INDUSTRIAL
STANDARDS [FAR SUBPART 46.203(A), (1)].
THIS PRODUCT HAS BEEN DETERMINED TO BE OR CONTAINS (AS CHECKED BELOW):
(X) ENGINEERING CRITICAL IN APPLICATION
( ) CRITICAL CHARACTERISTICS
(X) MAJOR CHARACTERISTICS
(X) MINOR CHARACTERISTICS, ALL EXCEPTING CRITICAL AND MAJOR
( ) COMPLEX
( ) AVAILABLE AS A COMMERCIAL PRODUCT
WHEN MATERIALS, PROCESSES OR COMPONENTS ARE TO BE OBTAINED FROM DIRECTED
SPE4A7-26-T-663J
SECTION B
SOURCES AS INDICATED HEREIN OR IN THE SPECIFICATIONS, ALTERNATE SOURCES
MAY ONLY BE UTILIZED UPON PRIOR APPROVAL BY THE CONTRACTING OFFICER OF
THIS PROCURING ACTIVITY AS A DEVIATION.
BIDDERS SHALL NOTIFY THIS PROCURING ACTIVITY AT THE TIME OF QUOTATION OF
ANY DRAWING, SPECIFICATION OR STANDARD WHICH IS OF MORE CURRENT DATA
REVISION THAN THOSE SHOWN ON THE DATA LISTING OR IN THESE ENGINEERING
NOTES. DETERMINATION OF ACCEPTABILITY OF THE MORE CURRENTLY DATED DATA
WILL BE MADE BY THE RESPONSIBLE ENGINEERING OFFICE OF THIS PROCURING
ACTIVITY.
LOWER TIER SPECIFICATIONS LISTED IN OR REFERENCED BY FIRST TIER
SPECIFICATIONS MAY NOT BE SHOWN ON THE DATA LISTS OR ENGINEERING NOTES
ACCOMPANYING THIS CONTRACT BUT ARE NONETHELESS REQUIRED BY THIS CONTRACT
FOR COMPLIANCE. EXCEPTIONS WOULD OCCUR ONLY WHEN SUCH LOWER TIER
REQUIREMENTS HAVE BEEN SPECIFICALLY WAIVED OR SUBSTITUTE
SPECIFICATIONS/REQUIREMENTS ARE DESIGNATED HEREIN.
REPORTS, PROCESS SHEETS, INSPECTION METHODS SHEETS AND ALL OTHER
DOCUMENTS REQUIRED BY SPECIFICATIONS IMPOSED BY THIS CONTRACT FOR
CONTRACTOR COMPLIANCE WHICH WERE PREVIOUSLY REQUIRED TO BE SUBMITTED TO
A PRIME DESIGN CONTRACTOR SHALL BE HELD AT THAT FACILITY FOR REVIEW BY
GOVERNMENT PERSONNEL. WHEN PRIME DESIGN SOURCE SPECIFICATIONS REQUIRE OR
PROVIDE FOR PARTICIPATION BY THAT PRIME SOURCE QUALITY, MANUFACTURING,
LABORATORY OR ENGINEERING SUPPORT SERVICES, THESE REQUIREMENTS OR
PROVISIONS DO NOT APPLY WHEN THE CONTRACT WAS ISSUED BY THIS PROCURING
ACTIVITY. FOR THESE SERVICES OR DIRECTION PERTAINING THERETO, CONTACT
THE GOVERNMENT CONTRACT ADMINISTRATION OFFICE OR THIS PROCURING ACTIVITY
FOR ASSISTANCE.
THE CONTRACTOR IS RESPONSIBLE FOR ASSURING THAT ALL DIMENSIONS,
CONDITIONS, TESTS AND TEST RESULTS IDENTIFIED IN THESE ENGINEERING
NOTES, APPLICABLE DRAWINGS, SPECIFICATIONS AND CONTRACT QUALITY
REQUIREMENTS ARE MET BY THEMSELVES AND THEIR SUPPLIERS. THIS REQUIREMENT
APPLIES TO ALL CHARACTERISTICS WHETHER THOSE CHARACTERISTICS HAVE BEEN
SPECIFICALLY DESIGNED AS BEING CRITICAL, MAJOR OR ARE THOSE MINOR
CHARACTERISTICS NOT SPECIFICALLY DESIGNATED AS SUCH.
PROCESS DATA REQUIREMENTS (CHECK WHEN APPLICABLE)
( ) PRIOR TO BEGINNING OF MANUFACTURE, THE CONTRACTOR WILL NOTIFY THE
ENGINEERING OFFICE OF THIS PROCURING ACTIVITY OF ALL MANUFACTURING
PROCESS AND PROCESSING PROCEDURES INTENDED FOR USE IN PRODUCTION OF THIS
PRODUCT. ONCE THESE PROCESSES ARE ESTABLISHED, NO CHANGES SHALL BE MADE
WITHOUT PRIOR APPROVAL OF THE ENGINEERING OFFICE OF THIS PROCURING
ACTIVITY.
( ) SERIALIZATION OF PARTS (CHECK WHEN APPLICABLE)
SERIALIZATION OF EACH PART/ASSEMBLY (CONTRACT END ITEM) IS REQUIRED.
STABLE BASE DRAWINGS: (CHECK WHEN APPLICABLE)
(X) WHEN THE USE OF STABLE BASE DRAWINGS IS REQUIRED, THE FOLLOWING
SHALL APPLY:
A. STABILIZE BY ALLOWING THE STABLE BASE DRAWING TO REST FLAT AND
UNRESTRAINED ON A FLAT SURFACE OVERNIGHT AT ROOM TEMPERATURE PRIOR TO
USE.
B. DO NOT STRETCH OR OTHERWISE APPLY STRESS.
C. CHECK THE DIMENSIONAL ACCURACY OF THE GRID LINES. THE DIMENSION
BETWEEN ADJACENT GRID LINES MUST BE WITHIN .005 INCH. THE GRID LINES
SHALL BE MEASURED VERTICALLY, HORIZONTALLY AND DIAGONALLY, TO INSURE
THAT THE GRIDS ARE WITHIN A TOLERANCE OF .005 INCH. THE TOLERANCE IS
ACCUMULATED OVER THE LENGTH AND WIDTH OF THE STABLE BASE DRAWING.
D. TRAMMEL POINTS SHALL BE MEASURED TO WITHIN .010
E. WHEN ROLLING STABLE BASE DRAWINGS, DO NOT ROLL LESS THAN 3 INCHES IN
DIAMETER.
F. IF THE ABOVE TOLERANCE POINTS PROVE TO BE INACCURATE, RECORD THE
DISCREPANCIES IMMEDIATELY AND NOTIFY IN WRITING. OC-ALC/PKXDA AND THE
ADMINISTRATIVE CONTRACTING OFFICER (ACO).
RELEASE OF THIS DATA TO A FOREIGN-OWNED, CONTROLLED OR INFLUENCED
COMPANY IS DEPENDENT UPON THE APPROVAL OF THE FOREIGN DISCLOSURE
OFFICE.REFERENCE ALL DETAIL AND OR TIERED DRAWINGS, SPECIFICATIONS AND
DOCUMENTS:
THE REQUIRED USE OF A CLASS 1 ODS AS DEFINED IN CLAUSE H-305 AND OR
L-513 IS PROHIBITED. THE CONTRACTOR MUST USE THE ALTERNATE PROCESSES AND
OR CHEMICALS SPECIFIED IN THE APPLICABLE DRAWINGS, SPECIFICATIONS AND
DOCUMENTS.
THE CONTRACTOR SHALL USE THE MOST CURRENT AMENDMENTS APPLICABLE TO EACH
MIL SPEC, MIL STD, INDUSTRY SPEC OR INDUSTRY STD AS OF THE EFFECTIVE
SPE4A7-26-T-663J
SECTION B
DATE OF THIS CONTRACT UNLESS OTHERWISE NOTED.
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS
(MANUFACTURERS AND NON-MANUFACTURERS)
RQ002: CONFIGURATION CHANGE MANAGEMENT ENGINEERING CHANGE PROPOSAL
REQUEST FOR VARIANCE (DEVIATION OR WAIVER)
RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RQ032: EXPORT CONTROL OF TECHNICAL DATA
This item has technical data some or all of which is subject to export-control of either the International Traffic in Arms regulations (ITAR) or the Export Administration Regulations (EAR), and cannot be exported without prior authorization from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and nationals whether located in the United States or abroad. This requirement applies equally to foreign national employees and U.S. companies and their foreign subsidiaries. DFARS 252.225-7048 is applicable to this data.
The Defense Logistics Agency (DLA) limits distribution of export-control technical data to DLA contractors that have an approved US/Canada Joint Certification Program (JCP) certification, have completed the Introduction to Proper Handling of DOD Export-Controlled Technical Data Training and the DLA Export-Controlled Technical Data Questionnaire (both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. NSN/Part Number: 1560-01-154-9008 Quantity: 1 EA Purchase Request: 7017917153QTY: 1 Delivery: 171 days ADO