Fuell Stands

THIS IS NOT A SOLICITATION. This is a Sources Sought announcement only. This is not a request for quotes (RFQ), invitation for bid (IFB), request for proposal (RFP), request for application (RFA) or an announcement of a solicitation and does not assume the government will award a contract or proceed with any of the above solicitations in the near future. This synopsis is issued for the sole purpose of the 55th Contracting Squadron to conduct Market Research in accordance with FAR Part 10. GENERAL DESCRIPTION: This acquisition is for the 55th MXS located at Offutt AFB. This acquisition is to provide the following items: 1(ea) RC-135 Wing Maintenance Stand -All Aluminum Construction -Supported Cantilever Ladder -30" Wide Grip Strut Steps -125" Platform height -120" Clear height -36" Clear length under top deck -42" Guardrails -Swing gate at top step -Chain on rear exit -500lb Capacity -5x2 Dual locking swivel casters in front & 5x2 Rigid (rear) -Swivel Section: Cold?forged top plate, yoke and button are all heat treated to prevent brinelling, improve swivel action and increase service life. -Finish: Corrosion resistant zinc -Wheel Bearings: Roller -Capacity (lbs.): 1050 -Diameter: 5 Inch -Width: 2" -Overall Height: 6 1/2" -Wheel Type: Polyurethane on Aluminum 1(ea) RC-135 Landing Gear Stand All Aluminum Construction -36" Wide Grip Strut Steps on articulating ladder -Diamond Plate Deck on platforms -2000lb Platform Capacity -Scissor lift raises platforms 18" from 30" to 48" -removable guardrails -Scissor Lift -SCISSOR LIFT TABLE (5000 LBS. CAPACITY) -Platform: 60"w x 60 "l checker plate platform -Base: 60"w x 60 "l -Low Height: 9", Travel: 59" , Total: 68" -Lifting Lugs , Maintenance Strut and ( Up Limit Switch) -Power: A/C 220v/3ph/1hp vertical mounted power pack remote mounted c/w hand controls with pendant holder and 10 ft of cable and 10 ft of hose and power cord. -Redundant Saftey System incorporated in Scissor Lifts -Articulating stair to access lower platform -29 degree at 30" height & 50 degree at 48" height -5x2 Dual locking swivel casters -Swivel Section: Cold?forged top plate, yoke and button are all heat treated to prevent brinelling, improve swivel action and increase service life. -Finish: Corrosion resistant zinc -Wheel Bearings: Roller -Capacity (lbs.): 1050 -Diameter: 5 Inch -Width: 2" -Overall Height: 6 1/2" -Wheel Type: Polyurethane on Aluminum 1(ea) RC-135 Outboard Tank Stand All Aluminum Construction -36" Wide Grip Strut Steps on articulating ladder -Diamond Plate Deck on platforms -2000lb Platform Capacity -Scissor lift raises platforms 2' from 60" to 84" with two steps up to second platform at 78" & 102" -2 Scissor Lifts working in tandem -SCISSOR LIFT TABLE (5000 LBS. CAPACITY) -Platform: 96"w x 101 "l checker plate platform -Base: 68"w x 88 "l -Low Height: 9", Travel: 59" , Total: 68" -Lifting Lugs , Maintenance Strut and ( Up Limit Switch) -Power: A/C 220v/3ph/1hp vertical mounted power pack remote mounted c/w hand controls with pendant holder and 10ft of cable and 10ft of hose and power cord. -Redundant Saftey System incorporated in Scissor Lifts HOW TO SUBMIT: Respondents capable of performing this effort are requested to furnish sufficient supporting evidence. Please include your company's name, address, telephone number, point of contact with e-mail address, business size, Data Universal Numbering System (DUNS), Central Contractor Registration (CCR) number, Federal Cage Code, general description of the company with proven ability to meet requirements, and a description of similar contracts, to include agency name, contract number, dollar magnitude, performance period, and point of contact with telephone number. Your company must be registered in On Line Representations and Certifications (ORCA). To register, go to http://orca.bpn.gov. Respondents capable of providing this service are requested to submit capability information electronically to scott.deloera@offutt.af.mil. A verification e-mail will be sent upon receipt (as a reply to your e-mail). If you do not receive verification, contact SSgt Scott DeLoera at (402) 294-2632 or SSgt Brian Grant at (402) 232-8657 for further instructions. Reponses are due by close of business on 24 September 2010. Responses to this announcement should indicate whether the respondent is a small business, 8(a) concern, veteran-owned small business, service-disabled veteran-owned small business, HUBZone small business, small disadvantaged business, women-owned small business, or historically black college or university (HBCU) or minority institution (MI) (as defined by the clause at DFARS 252.226-7000). Offerors should indicate their intent to submit a quote if a Request for Quote is issued and if their company will be a prime contractor, subcontractor, teaming partner, etc. The North American Industrial Classification System (NAICS) is 332999; Small business size standard is 500 employees. This RFI is not a commercial solicitation per FAR Part 12. This synopsis neither constitutes a Request for Quote, nor does it restrict the Government to an ultimate acquisition approach. This Sources Sought should not be construed as a commitment by the Government for any purpose. Any information submitted by respondents to this sources sought is strictly voluntary and any offer submitted by such a firm will be evaluated without prejudice. The Government will not pay for any information that is submitted by respondents to this Sources Sought. Questions should be addressed via e-mail to the contract administrator. CONTACT: SSgt Scott DeLoera via email at scott.deloera@offutt.af.mil or SSgt Brian Grant via e-mail at brian.grant@offutt.af.mil.