This Solicitation opportunity from Department Of Defense was posted on June 24, 2026. The submission period has ended. Browse the details below for market research, or find similar active opportunities.
GASKET
Contract Overview
Solicitation details, issuing organization, response deadlines, documents, and interested companies for this government contract opportunity.
Active Opportunities Like This One
AI Contract Overview
Solicitation SPE7L1-26-T-759W is a request for quotations issued by the Department of Defense, DLA Land and Maritime, for the procurement of one commercial off-the-shelf gasket, NSN 5330-01-670-1714. The required delivery is 20 days after the date of award to McConnell AFB, Kansas, with terms set as FOB Destination. Quotations must be submitted electronically via the DLA Internet Bid Board System by July 6, 2026. The contract mandates strict adherence to technical and quality requirements, including a prohibition on asbestos and the requirement for supply chain traceability documentation. Quality assurance is governed by ISO 9001:2015 standards, with sampling conducted per MIL-STD-1916 or ASQ H1331, requiring zero non-conformances for acceptance. Packaging and marking must comply with MIL-STD-2073-1E and MIL-STD-129, with specific FAA bare item marking and airworthiness approval requirements. Administrative compliance includes electronic invoicing through Wide Area WorkFlow and cybersecurity adherence to NIST SP 800-171. Contractors must also comply with hazardous material labeling under 29 CFR 1910.1200 and provide Material Safety Data Sheets where applicable. The procurement is subject to various FAR and DFARS clauses, including those regarding the safeguarding of covered defense information and the prohibition of certain telecommunications equipment.
General Info
Place of Performance
53241 TOPEKA ST BLDG 1169, MCCONNELL AFB, KS, 67221-3710, USASet-Aside
Timeline
Submission Closed
Organization & Contact Information
Full Description
GASKET
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RP003: PRESERVATION, PACKAGING, PACKING AND MARKING REQUIREMENTS FOR
FEDERAL AVIATION ADMINISTRATION COMMERICAL MATERIAL
RQ002: CONFIGURATION CHANGE MANAGEMENT ENGINEERING CHANGE PROPOSAL
REQUEST FOR VARIANCE (DEVIATION OR WAIVER)
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RQ046: FAA Bare Item Marking Requirements
RQ018: CONTRACTOR RETENTION OF SUPPLY CHAIN TRACEABILITY DOCUMENTATION (AUG 2016) This item requires supply chain traceability documentation in accordance with DLA Directive (DLAD) Procurement Notes #C03 Contractor Retention of Supply Chain Traceability Documentation (AUG 2016)#. The full text of C03 can be found in the DLAD Procurement Notes on the Web at: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx. http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx. (End of TQ Requirement)
THIS ITEM IS IDENTIFIED AS A COMMERCIAL OFF THE SHELF (COTS) ITEM
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
SPE7L1-26-T-759W
SECTION B
The following Contract Data Requirements Lists (CDRLs), DD Form 1423s, apply to this procurement. Review the Technical Data Package (TDP) for additional information.
RQ019: Federal Aviation Administration (FAA) Airworthiness Approval
"ITEMS SUPPLIED MUST BE FREE OF ASBESTOS. LISTED CODE AND PART NUMBERS CONTAINING ASBESTOS ARE NO LONGER ACCEPTABLE, AND ANY ALTERNATIVE ITEM/MATERIAL MUST BE APPROVED IN ACCORDANCE WITH CLAUSE L30 AND PROVISION 4 CONDITIONS FOR NSN/Part Number: 5330-01-670-1714 Quantity: 1 EA Purchase Request: 7017184780QTY: 1 Delivery: 20 days ADO
More opportunities from Department Of Defense → LAND SUPPLY CHAIN
Same awarding agency
Earlier notices in this NAICS code
Posted before this notice, open and closed
Find Active Opportunities Like This
Get AI-powered intelligence on the opportunities still open
Every page of the solicitation package shredded into a compliance breakdown
AI-powered matching based on your capabilities and past performance
Competitor and incumbent history on the requirement
Automated alerts on amendments, Q&A deadlines, and award
Join 750+ contractors already using CLEATUS