HOIST, CHAIN

HOIST,CHAIN
HOIST, CHAIN
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
MILITARY SPEC MIL-H-904 TITLED "HOISTS, CHAIN, HAND-OPERATED, HOOK AND
TROLLEY SUSPENSION" APPLIES. 3 TON CAPACITY, 10 FT LIFT, LOW HEADROOM.
TROLLEY SUSPENSION: 8 GEARED, STANDARD 10 INCH I-BEAM., WHEELS VERTICAL.
TRACK HEIGHT: ANY ACCEPTABLE. FULLY RAISED POSITION TRACK UNDERSIDE
DISTANCE TO LOAD: 7.750 INCH NOMINAL. MOUNTING POSITION: RIGHT ANGLE.
TROLLEY TRACK CLAMP, PULL TO TRAVERSE TROLLY 21 POUNDS. FLANGE WIDTH:
4.330. CORROSION RESISTANT FINISHED CHAINS. SINGLE CORROSION RESISTANT
FINISHED HOOK SHALL BE SWIVEL TYPE WITH SAFETY DEVICES. MINIMUM CURVE
I-BEAM TRACK 42 INCH RADIUS. CLASS 1 AND TYPE G. PAINTING SHALL BE PER
MANUFACTURE'S STANDARD COMMERCIAL PRACTICE.
QUALIFIED SOURCES:
COLUMBUS MCKINNON CORPORATION (80735)
THIS NSN IS LISTED AS A PRIMARY QPL OR QML
THEREFORE THE QUALIFIED PRODUCTS LIST OR
QUALIFIED MANUFACTURERS LIST IS APPLICABLE.
CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE
USED NOR INCORPORATED IN ANY ITEMS TO BE
DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION
SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT
DOES NOT ALLEVIATE ANY PRODUCT REQUIREMENTS.
SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR
APPROVAL UNLESS THEY ARE AUTHORIZED BY THE
SPECIFICATION REQUIREMENTS.
THE CONTRACTOR WILL OVERPACK ONE EACH
MANUFACTURER'S COMMERCIAL MANUAL CONSISTING
OF OPERATION, SERVICES, MAINTENANCE, REPAIR NSN/Part Number: 3950-00-889-8738 Quantity: 1 EA Purchase Request: 7018588567QTY: 1 Delivery: 165 days ADO