This Solicitation opportunity from Department Of Defense was posted on May 12, 2026. The submission period has ended. Browse the details below for market research, or find similar active opportunities.
HOOK, CHAIN, S
Contract Overview
Solicitation details, issuing organization, response deadlines, documents, and interested companies for this government contract opportunity.
Active Opportunities Like This One
AI Contract Overview
The contract specifies the procurement of 5,852 units of a hook and chain assembly, part number NAS1090-2, manufactured to meet the National Aerospace Standard NAS1090 Revision 5 dated June 10, 2010, and referenced against drawing number 13873 008218404-20007 Revision dated January 7, 2020. The item is designated as a critical application component intended for safety chain assemblies and use with the NAS1091 streamer assembly, with strict performance criteria requiring the hook to withstand specified pull loads without permanent loop deformation exceeding 0.031 inch. All components must conform to dimensional tolerances of ±.031 inches unless otherwise specified, and dimensioning must adhere to ANSI Y14.5M-1982. The material and manufacturing standards take precedence over referenced documents, and existing inventory manufactured to prior revisions may be procured until depleted. Quality assurance is governed by the DLA Master List of Technical and Quality Requirements, incorporating multiple RQ codes including RQ001 for tailored quality requirements, RQ002 for configuration change management, RQ009 for inspection and acceptance at origin, RQ011 for removal of government identification from non-accepted items, and RQ017 for physical identification of bare items. Sampling must follow MIL-STD-1916 or ASQ H1331 Table 1 with zero non-conformances required for acceptance unless otherwise stated; attributes are classified with AQLs of 0.1 for critical, 1.0 for major, and 4.0 for minor. Certificate of Conformance is authorized under FAR 52.246-15 unless withheld by a Quality Assurance Letter of Instruction. Packaging must comply with MIL-STD-2073-1E, with specific preservation method 33 (cleaning and drying), wrap material GB, unit container BL, intermediate container E5, and pack code U. Marking shall follow MIL-STD-129, including barcoding for traceability, with no special marking code required. Palletization must meet DLA’s RP001 packaging requirements. The item is delivered FOB origin, with inspection and acceptance occurring at the destination—Cherry Point, NC—after a 171-day delivery timeline, with a need
General Info
Agency
Contract Value
$3,920.84NAICS
Place of Performance
PHANTOM RD BLDG 147 BAY A, CHERRY POINT, NC, 28533-5040, USASet-Aside
Awardee
Award Issued Date
Timeline
Submission Closed
Organization & Contact Information
Full Description
HOOK, CHAIN, "S" P/N NAS1090-2
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RC001: DOCUMENTATION REQUIREMENTS FOR SOURCE APPROVAL REQUEST (SAR)
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ002: CONFIGURATION CHANGE MANAGEMENT ENGINEERING CHANGE PROPOSAL
REQUEST FOR VARIANCE (DEVIATION OR WAIVER)
RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RQ017: PHYSICAL INDENTIFICATION/BARE ITEM MARKING
RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS
(MANUFACTURERS AND NON-MANUFACTURERS)
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
CERTIFICATE OF CONFORMANCE PROCEDURES (FAR 52.246-15) ARE AUTHORIZED,
UNLESS WITHELD BY A QUALITY ASSURANCE LETTER OF INSTRUCTION.
ENGINEERING NOTES:
(1) -1 AND -2 INTENDED FOR USE WITH NAS1091 STREAMER ASSEMBLY. -3 USED
AS PART OF SAFETY CHAIN ASSEMBLIES SECURING SEAL CAP ASSEMBLIES, SUCH AS
AN929.
(2) AFTER CLOSING LOOPS, HOOK SHALL WITHSTAND A PULL AS SHOWN IN TABLE
ABOVE WITHOUT PERMANENT OPENING OF LOOPS IN EXCESS OF .031 INCH.
SPE4A5-26-T-130C
SECTION B
(3) DIMENSIONS IN INCHES. TOLERANCES UNLESS OTHERWISE SPECIFIED:
DECIMALS ±.031.
(4) THIS STANDARD TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN.
(5) UNLESS OTHERWISE SPECIFIED, PART INVENTORY MANUFACTURED TO PREVIOUS
REVISIONS OF THE APPLICABLE DRAWING OR SPECIFICATION MAY BE PROCURED AND
USED UNTIL STOCK IS DEPLETED.
(6) UNLESS OTHERWISE SPECIFIED HEREIN, REFERENCED DOCUMENTS SHALL BE THE
ISSUE IN EFFECT ON DATE OF MANUFACTURE. HOWEVER, EXISTING MATERIAL
INVENTORY CERTIFIED TO A PREVIOUS REVISION OF THE APPLICABLE MATERIAL
SPECIFICATION(S) IS ACCEPTABLE FOR USE UNTIL DEPLETION.
(7) DIMENSIONING AND TOLERANCING PER ANSI Y14.5M-1982
CRITICAL APPLICATION ITEM
IAW BASIC NON GOVT STD NAS1090
REVISION NR 5 DTD 06/10/2010
PART PIECE NUMBER: NAS1090-2
IAW REFERENCE DRAWING NR 13873 008218404-20007
REVISION NR DTD 01/07/2020
PART PIECE NUMBER:
IAW REFERENCE QAP 13873 SQAP008218404-19339
REVISION NR DTD 12/05/2019
PART PIECE NUMBER:
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 7016752832 0001 EA 5,852.000
NSN/MATERIAL:4030008218404
DELIVERY (IN DAYS):0171
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: DESTINATION
ACCEPTANCE POINT: DESTINATION
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:33 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:GB CUSH/DUNN MAT:NA CUSH/DUNN THKNESS:C
UNIT CONT:BL OPI:O
INTRMDTE CONT:E5 INTRMDTE CONT QTY:AAA
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:00 -00 No special marking
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
SPE4A5-26-T-130C
SECTION B
PR: 7016752832 PRLI: 0001 CONT’D
PARCEL POST ADDRESS:
SW3113
DLA DISTRIBUTION CHERRY POINT
PHANTOM RD BLDG 147 BAY A
CHERRY POINT NC 28533-5040
US
FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE
C20 AND CONTRACT
FREIGHT SHIPPING ADDRESS:
SW3113
DLA DISTRIBUTION CHERRY POINT
PHANTOM RD BLDG 147 BAY A
CHERRY POINT NC 28533-5040
US
Need Ship Date:11/08/2026 Original Required Delivery Date:12/04/2026
SPE4A5-26-T-130C NSN/Part Number: 4030-00-821-8404 Quantity: 5,852 EA Purchase Request: 7016752832QTY: 5852 Delivery: 171 days ADO
More opportunities from Department Of Defense → ASC SUPPLIER OPER OEM DIVISION
Same awarding agency
Find Active Opportunities Like This
Get AI-powered intelligence on the opportunities still open
Every page of the solicitation package shredded into a compliance breakdown
AI-powered matching based on your capabilities and past performance
Competitor and incumbent history on the requirement
Automated alerts on amendments, Q&A deadlines, and award
Join 650+ contractors already using CLEATUS