J&A NR3 HPBAC NEW WORK RCC 510N

The following changes and/or additions apply to the work requirements of the original specification: 1. SCOPE: (A) 1.1 Title: Overhaul #3 High Pressure Breathing Air Compressor (A) 1.2 Location of Work: (A) 1.2.1 PASSAGEWAY (2-143-2-L) (A) 1.3 Identification: (A) 1.3.1 Quantity (One EA), Compressor Breathing Air, MFR: Meggitt North Hollywood Inc., MFR ID: K966037-1, APL: 06A040002 (A) 2. REFERENCES: (A) 2.1 (FY22) (A) 2.2 S6220-ES-MMC-010 Rev 1 Compressor, High Pressure Breathing Air Model K966037-1 (A) 3. REQUIREMENTS: (A) 3.1 Accomplish the requirements of 009-90 of 2.1 for the services of a qualified on-site technical representative to (A) disassemble, inspect, overhaul, install, and test the equipment listed in 1.3 and located in 1.2. (G) "PRE-REPAIR OPERATIONAL TEST" 3.2 Accomplish a pre-repair operational test and inspection of the equipment identified in 1.3 to assess repairs requiredor an overhaul, using section 3.3 of 2.2 for guidance. Record operational parameters and abnormal conditions.3.3 Remove and dispose of system fluid from the equipment. (A) 3.4 Remove and disassemble the equipment, using Chapter 6 of 2.2 for guidance. (A) 3.4.1 Clean each exposed part free of oil, grease and foreign matter, leaving no residue or injurious effects. (A) 3.4.2 Inspect each part for wear and defects, using Chapter 6, corrective maintenance of 2.2 for guidance and for accept or (A) reject criteria. 3.4.2.1 Measure and record each size and clearance, using 2.2 for guidance. (A) 3.4.2.2 Include sizes and clearances for each wearing part, bearing surface, thrust and journal bearing, seal and packing area, (A) and physical condition of each part not specified for renewal. 3.4.2.3 Submit one legible copy, in hard copy or approved transferrable media, of a report listing results of the requirements of (A) 3.4.2 through 3.4.2.2 to the SUPERVISOR. 3.4.3 Chase and tap each exposed threaded area. (A) 3.4.4 Remove each high spot, burr, abrasion, nick, corrosion, gasket material, and foreign matter from each exposed flange (A) and mating surface. 3.4.5 Remove each burr and high spot from each exposed sliding surface, screw thread, key, and keyway. (A) 3.5 Assemble, align, adjust, and connect the equipment listed in 1.3, using Chapter 6 of 2.2 for guidance.3.5.1 Fit and install new the following parts: One EA O-Ring 19 2.2 7-2 N2485 One EA Gasket, Copper 89 2.2 7-2 008263 One EA Gasket, Copper 91 2.2 7-2 N01316 One EA Gasket, Copper 93 2.2 7-2 N01316 One EA Gasket, Copper 95 2.2 7-2 N01316 4 EA Gasket, Copper 97 2.2 7-2 N01316 2 EA Gasket 101 2.2 7-2 004479 4 EA Gasket 106 2.2 7-2 N00293 One EA Gasket 110 2.2 7-2 008264 One EA Gasket 112 2.2 7-2 004479 One EA O-Ring 115 2.2 7-2 N03556 One EA Gasket 121 2.2 7.2 N1316 One EA O-Ring 125 2.2 7.2 N03556 One EA Gasket 127 2.2 7.2 N1316 2 EA O-Ring 134 2.2 7-2 N07091 One EA Gasket, Copper 135 2.2 7-2 N04051 One EA Gasket, Copper 141 2.2 7-2 N03625 2 EA O-Ring 148 2.2 7-2 N07091 One EA Gasket, Copper 154 2.2 7-2 N01059 One EA Gasket, Oil Pump 155 2.2 7-2 002010 One EA Gasket, Copper 160 2.2 7-2 056983 One EA Gasket, Copper 162 2.2 7-2 N01316 One EA O-Ring 164 2.2 7-2 N04385 One EA Head, Discharge Valve 167 2.2 7-2 060534 One EA O-Ring 169 2.2 7-2 N04776One EA Head, Inlet Valve 173 2.2 7-2 060530 2 EA O-Ring 175 2.2 7-2 N02320 One EA O-Ring 180 2.2 7-2 N03731 2 EA Gasket, Copper 190 2.2 7-2 N00293 One EA O-Ring 193 2.2 7-2 N03997 One EA Valve, Inlet 194 2.2 7-2 N15273 One EA Valve, Discharge 195 2.2 7-2 N15274 2 EA Gasket, Valve 196 2.2 7-2 056668 One EA O-Ring 202 2.2 7-2 N07063 One EA Gasket, Copper 205 2.2 7-2 N04051 One EA O-Ring 206 2.2 7-2 N03731 2 EA Gasket, Copper 218 2.2 7-2 N00293 2 EA O-Ring 221 2.2 7-2 N03997 One EA Valve, Inlet 222 2.2 7-2 N04067 One EA Valve, Discharge 223 2.2 7-2 N04068 2 EA Gasket, Valve 224 2.2 7-2 056668 One EA O-Ring 230 2.2 7-2 N03731 One EA Gasket, Copper 238 2.2 7-2 N00293 One EA Gasket, Copper 243 2.2 7-2 N01316 2 EA O-Ring 247 2.2 7-2 N04085 One EA Valve, Inlet 249 2.2 7-2 N02975 One EA Valve, Discharge 250 2.2 7-2 N04149 2 EA Gasket, Valve 251 2.2 7-2 005298 One EA Gasket, Valve Head 254 2.2 7-2 061183 One EA O-Ring 259 2.2 7-2 N02621 One EA V-Belt 276 2.2 7-2 BET0136 One EA O-Ring 281 2.2 7-2 N15106 One EA Gasket, Copper 298 2.2 7-2 N00293One EA Gasket, Bearing Cover 305 2.2 7-2 003177 One EA O-Ring 306 2.2 7-2 N15093 One EA Seal, Shaft 307 2.2 7-2 N18305 One EA Bearing, Roller 308 2.2 7-2 N18303 One EA Bearing, Roller 310 2.2 7-2 N18304 One EA Gasket, Bearing Cover 314 2.2 7-2 N18304 One EA Seal, Shaft 315 2.2 7-2 N15067 One EA Bearing, Roller 316 2.2 7-2 N02638 One EA O-Ring 320 2.2 7-2 N15412 One EA Gasket, Copper 322 2.2 7-2 N01316 3 EA Gasket, Crankcase 328 2.2 7-2 012386 One EA Seal, Shaft 330 2.2 7-2 N00086 One EA Gasket, Cover, Bearing 334 2.2 7-2 000149 One EA Bearing, Ball 335 2.2 7-2 N00091 2 EA Gasket, Copper 338 2.2 7-2 N00293 One EA Gasket, Copper 340 2.2 7-2 N00293 One EA Gasket, Copper 342 2.2 7-2 N00842 3 EA O-Ring 52 2.2 7-3 N04333 2 EA Gasket, Copper 73 2.2 7-3 N01316 One EA Gasket, Copper 76 2.2 7-3 N04051 One EA O-Ring 83 2.2 7-3 N02720 One EA O-Ring 86 2.2 7-3 RNG0070 One EA O-Ring 89 2.2 7-3 N02507 One EA O-Ring 91 2.2 7-3 N04178 One EA O-Ring 98 2.2 7-3 N07091 One EA O-Ring 99 2.2 7-3 N02720One EA O-Ring 102 2.2 7-3 RNG0070 One EA O-Ring 105 2.2 7-3 N02507 One EA O-Ring 107 2.2 7-3 N04178 One EA Gasket, Fitting 27 2.2 7-4 N04499 2 EA O-Ring 31 2.2 7-4 N04735 One EA O-Ring 35 2.2 7-4 N15133 2 EA O-Ring 43 2.2 7-4 N04735 2 EA O-Ring 56 2.2 7-4 N04735 One EA Bearing, Pulley End 9 2.2 7-5 K600133-10-9 One EA Bearing, Front End 10 2.2 7-5 K600133-10-10 3.5.2 Fill equipment to the full mark with new oil (4 Quarts) conforming to MIL-PRF-17331, using 2.2 for guidance. (A) (G) "OPERATIONAL TEST" 3.6 Accomplish an operational test of equipment listed in 1.3, using section 3.3 of 2.2 and per technical representative for (A) guidance. Allowable pressure loss: None. 3.6.1 Verify conformance and operations capabilities in accordance with manufacturer's specifications. (A) 3.7 Accomplish the requirements of 009-32 of 2.1 for each new and disturbed surface.