LAMP, INCANDESCENT
Contract Overview
Solicitation details, issuing organization, response deadlines, documents, and interested companies for this government contract opportunity.
AI Contract Overview
The contract is for the procurement of 10 incandescent lamps with NSN 6240-00-905-8505 under solicitation SPE8E7-26-T-3456, issued by the Defense Logistics Agency on behalf of the Department of Defense. Delivery is required within 10 days after award, with the response deadline set for August 17, 2026. The item must comply with DLA packaging and technical requirements incorporated by reference, including MIL-STD-1916 or ASQ H1331 for sampling, where zero non-conformances are required unless otherwise specified, and critical, major, and minor attributes must be verified at levels VII, IV, and II respectively or with AQLs of 0.1, 1.0, and 4.0. The manufacturer’s symbol must be marked directly on the item’s surface and must be registered in MIL-HDBK-57, with exceptions for small fasteners under 0.190 inches in thread diameter, and no markings are permitted on bearing surfaces. Packaging must clearly identify exterior shipping containers only, and covered defense information may apply. The contract is fully competitive and governed by federal specifications, with the official drawing referenced available via DIBBS during the solicitation period. The place of performance is Camp Lejeune, North Carolina, with Kelly Mitchell designated as the primary point of contact.
General Info
Agency
NAICS
Place of Performance
PSC BOX 20143, CAMP LEJEUNE, NC, 28542-0125, USSet-Aside
Documents
(1)AI Contract Breakdown
Uniform Contract FormatWhat is UCF?
Uniform Contract Format (UCF) uses AI to break down any contract into standardized sections—scope, pricing, deliverables, and evaluation criteria.
Timeline
Response Deadline
Organization & Contact Information
Full Description
LAMP,INCANDESCENT
LAMP INDUSTRY TRADE NO. 1034A
MARK EXTERIOR SHIPPING CONTAINERS ONLY.
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RD003, COVERED DEFENSE INFORMATION POTENTIALLY APPLIES
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
STANDARD
ITEM SURFACE MARKING REQUIREMENT: IN ADDITION TO MARKING REQUIREMENTS
DEFINED BY TECHNICAL DATA, THE MANUFACTURER'S SYMBOL IS REQUIRED AND
SHALL BE APPLIED DIRECTLY TO THE SURFACE OF THIS ITEM. THE
MANUFACTURER'S SYMBOL MUST BE LISTED IN MIL-HDBK-57. DO NOT PLACE ANY
MARKINGS ON BEARING SURFACES. MANUFACTURER'S SYMBOL IS NOT REQUIRED ON
FASTENERS WITH A THREAD DIAMETER OF 0.190 INCHES AND SMALLER.
FOR MANUFACTURER'S SYMBOL REGISTRATION INFORMATION AND INQUIRIES PLEASE
VISIT THE MIL-HDBK-57 URL AT:
http://www.dla.mil/TroopSupport/IndustrialHardware/Engineering-and-Techn http://www.dla.mil/TroopSupport/IndustrialHardware/Engineering-and-Techn ical-services/logoreg/
THE DRAWING(S) LISTED BELOW ARE AVAILABLE AT DLA DURING "OPEN SOLICITATION ONLY". TO RECEIVE A COPY OF THE DRAWING(S)<(>,<)> FOR EBS SOLICITATIONS USE URL HTTPS://WWW.DIBBS.BSM.DLA.MIL/RFQ/
SPE8E7-26-T-3456
SECTION B
THIS NSN IS PROCURED AS FULLY COMPETITIVE IN
ACCORDANCE WITH A MILITARY / FEDERAL
SPECIFICATION/STANDARD. SEE NSN/Part Number: 6240-00-905-8505 Quantity: 10 EA Purchase Request: 7017722035QTY: 10 Delivery: 10 days ADO
Similar Contracts
Same NAICS industry code
More opportunities from Department Of Defense → Defense Logistics Agency
Same awarding agency
