This Solicitation opportunity from Department Of Defense was posted on May 28, 2026. The submission period has ended. Browse the details below for market research, or find similar active opportunities.
METER MOVEMENT, VERT
Contract Overview
Solicitation details, issuing organization, response deadlines, documents, and interested companies for this government contract opportunity.
Active Opportunities Like This One
AI Contract Overview
The contract solicitation SPE4A5-25-T-737A is for the procurement of two units of a METER MOVEMENT, VERTICAL POINTER with NSN 6695-01-267-7363, issued by the Department of Defense through DLA Aviation ASC Supplier Oper OEM Division. The item must be sourced exclusively from approved suppliers: Astronautics Corp. of America (CAGE 10138, P/N 133075), Jewell Instruments, LLC (CAGE 33005, P/N 223010-007), and Symetrics Industries, LLC (CAGE 22830, P/N 133075), with CAGE 11707 explicitly disqualified due to form, fit, and function noncompliance. Dealers and distributors must provide traceability to these approved sources to be considered. The procurement is a small business set-aside under NAICS code 334519, subject to the Berry Amendment and Buy American Act with a reduced threshold of $150,000, and requires full compliance with domestic sourcing restrictions and disclosure of any non-domestic materials. All offers must be submitted electronically via DLA’s eProcurement portal by the deadline of June 2, 2026, and require current, validated annual representations in SAM, including certifications for independent pricing, avoidance of trafficking in persons, employment eligibility verification, and prohibition on confidential agreements. The item must be manufactured and delivered in strict compliance with technical and quality requirements referenced through the DLA Master List of Technical and Quality Requirements identified by R and I numbers. Sampling must follow MIL-STD-1916, ASQ H1331 Table 1, or an equivalent zero-based plan, with critical, major, and minor attributes assigned verification levels VII, IV, and II or AQLs of 0.1, 1.0, and 4.0 respectively; unspecified attributes are deemed major. Acceptance is zero-defect, and MIL-STD-105/ASQ Z1.4 may be used only for sample sizing with zero non-conformances required for lot acceptance. Packaging must conform to MIL-STD-2073-1E with specified QUP, preservative method, and packaging codes, while marking must adhere to MIL-STD-129 with
General Info
Agency
NAICS
Place of Performance
2083 NORMANDY DRIVE DOOR 113 TO 134, NEW CUMBERLAND, PA, 17070-5002, USASet-Aside
Timeline
Submission Closed
Organization & Contact Information
Full Description
METER MOVEMENT, VERTICAL POINTER
RQ017: PHYSICAL INDENTIFICATION/BARE ITEM MARKING
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RD002, COVERED DEFENSE INFORMATION APPLIES
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS
(MANUFACTURERS AND NON-MANUFACTURERS)
RQ002: CONFIGURATION CHANGE MANAGEMENT ENGINEERING CHANGE PROPOSAL
REQUEST FOR VARIANCE (DEVIATION OR WAIVER)
RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RQ017: PHYSICAL INDENTIFICATION/BARE ITEM MARKING
The Government Procuring Activity has determined that Surplus is not Acceptable for this NSN. (End of TQ Requirement)
SAMPLING: THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION, STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICATION LEVELS OF VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
**************************NOTE ************************
CAGE:11707 IS NO LONGER AN APPROVED SOURCE PER THE ARMY DUE TO
FORM, FIT AND FUNCTION.
SPE4A5-25-T-737A
SECTION B
DEALER DISTRIBUTORS NEED TO PROVIDE TRACE TO APPROVED SOURCES TO
BE CONSIDERED FOR PROCUREMENT.
************************END OF NOTE ****************
CONFIG CONTROL
Astronautics Corp. of America CAGE 10138 P/N 133075
APPROVED SOURCES: Jewell Instruments, LLC CAGE 33005 P/N 223010-007
IDENTIFY TO:
SYMETRICS INDUSTRIES, LLC 22830 P/N 133075
JEWELL INSTRUMENTS LLC 33005 P/N 223010-007
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://www.dla.mil/Portals/104/Documents/DLMS/eApplications/LogDataAdmin/ UnitofIssueandPurchaseUnit.xlsx
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 7013721740 0001 EA 2.000
NSN/MATERIAL:6695012677363
DELIVERY (IN DAYS):0171
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: DESTINATION
ACCEPTANCE POINT: DESTINATION
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:10 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:00 CUSH/DUNN MAT:ZZ CUSH/DUNN THKNESS:Z
UNIT CONT:ZZ OPI:M
INTRMDTE CONT:NR INTRMDTE CONT QTY:AAA
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:00 -00 No special marking
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
SECURE MOVEMENT TO REINFORCED LID OF PLAS TIC CANNISTER OR BOX. SECURE POINTER TO PREVENT MOVEMENT OR DAMAGE TO THE POINTER DURING SHIPMENT.
SPE4A5-25-T-737A
SECTION B
PR: 7013721740 PRLI: 0001 CONT’D
PARCEL POST ADDRESS:
W25G1U
W1A8 DLA DISTRIBUTION
DDSP NEW CUMBERLAND FACILITY
2083 NORMANDY DRIVE DOOR 113 TO 134
NEW CUMBERLAND PA 17070-5002
US
FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE
C20 AND CONTRACT
FREIGHT SHIPPING ADDRESS:
W25G1U
W1A8 DLA DISTRIBUTION
DDSP NEW CUMBERLAND FACILITY
2083 NORMANDY DRIVE DOOR 113 TO 134
NEW CUMBERLAND PA 17070-5002
US
Need Ship Date:03/08/2026 Original Required Delivery Date:12/14/2026
SPE4A5-25-T-737A NSN/Part Number: 6695-01-267-7363 Quantity: 2 EA Purchase Request: 7013721740QTY: 2 Delivery: 171 days ADO
More opportunities from Department Of Defense → ASC SUPPLIER OPER OEM DIVISION
Same awarding agency
Find Active Opportunities Like This
Get AI-powered intelligence on the opportunities still open
Every page of the solicitation package shredded into a compliance breakdown
AI-powered matching based on your capabilities and past performance
Competitor and incumbent history on the requirement
Automated alerts on amendments, Q&A deadlines, and award
Join 650+ contractors already using CLEATUS