NUT, PLAIN, HEXAGON

NUT,PLAIN,HEXAGON
NUT,PLAIN,HEXAGON
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RQ002: CONFIGURATION CHANGE MANAGEMENT ENGINEERING CHANGE PROPOSAL
REQUEST FOR VARIANCE (DEVIATION OR WAIVER)
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
MERCURY OR MERCURY CONTAINING COMPOUNDS SHALL
NOT BE INTENTIONALLY ADDED TO<(>,<)> OR COME IN DIRECT
CONTACT WITH<(>,<)> ANY HARDWARE OR SUPPLIES FURNISHED
UNDER THIS CONTRACT. EXCEPTION: FUNCTIONAL MERCURY
USED IN BATTERIES, FLUORESCENT LIGHTS, REQUIRED
INSTRUMENTS; SENSORS OR CONTROLS; WEAPON SYSTEMS;
AND CHEMICAL ANALYSIS REAGENTS SPECIFIED BY NAVSEA.
PORTABLE FLUORESCENT LAMPS AND PORTABLE INSTRUMENTS
CONTAINING MERCURY SHALL BE SHOCK PROOF AND CONTAIN
A SECOND BOUNDARY OF CONTAINMENT OF THE MERCURY OR
MERCURY COMPOUND. (IAW NAVSEA 5100-003D).
NUT TYPE I, 0.875 INCH DIAMETER.
MATERIAL: NICKEL ALLOY GRADE 500,
ANNEALED AND HARDENED.
THREAD 0.875-14UNF-2B.
RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS
(MANUFACTURERS AND NON-MANUFACTURERS)
Unless otherwise stated, identification marking shall be in accordance with paragraph 4.1.b(2) of MIL-STD-130N. This is in addition to any required manufacturer's logo, lot number, and material identification markings.
THIS ITEM IS IDENTIFIED AS A COMMERCIAL ITEM (TO INCLUDE 'COMMERCIAL
OF A TYPE')
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPE7M2-26-T-6169
SECTION B
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
THIS ITEM IS DEFINED BY EITHER BY A MILITARY PART STANDARD, OR A PART
STANDARD PUBLISHED BY A CONSENSUS NON-GOVERNMENT STANDARDS ORGANIZATION.
HARDWARE MANUFACTURED TO THE CURRENT REVISION OF THE PART STANDARD
DEFINING THIS ITEM IS ACCEPTABLE.
HARDWARE MANUFACTURED IN THE PAST TO A PREVIOUS, BUT THEN CURRENT,
REVISION OF THE STANDARD IS ACCEPTABLE.
ANY HARDWARE MANUFACTURED FROM THE DATE OF THIS SOLICITATION FORWARD,
SHALL BE MANUFACTURED IN ACCORDANCE WITH THE CURRENT REVISION OF THE
PART STANDARD IN QUESTION.
MANDATORY MARKING REQUIREMENT PER
MIL-DTL-1222J TABLE I, AND PARAGRAPH 3.13.
MANDATORY MARKINGS FOR EACH NUT:
MATERIAL SYMBOL (.K.), MANUFACTURER'S
SYMBOL AND LOT NUMBER IN ACCORDANCE WITH
PARAGRAPH 3.13 OF MIL-DTL-1222.
THE NUTS WHICH ARE NOT MARKED IN
ACCORDANCE WITH THESE
REQUIREMENT ARE NOT ACCEPTABLE.
CRITICAL APPLICATION ITEM
TDP Rev A Gen 1 IAW BASIC SPEC NR MIL-DTL-1222J REVISION NR J DTD 12/08/2000 PART PIECE NUMBER: P/N M1222N1W14F20NCNN
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 7017775423 0001 EA 30.000
NSN/MATERIAL:5310015158592
DELIVERY (IN DAYS):0165
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: DESTINATION
ACCEPTANCE POINT: DESTINATION
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:10 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:00 CUSH/DUNN MAT:00 CUSH/DUNN THKNESS:0
SPE7M2-26-T-6169
SECTION B
PR: 7017775423 PRLI: 0001 CONT’D
UNIT CONT:10 OPI:O
INTRMDTE CONT:D3 INTRMDTE CONT QTY:AAA
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:00 -00 No special marking
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
PARCEL POST ADDRESS:
W62G2T
W1A8 DLA DIST SAN JOAQUIN
25600 S CHRISMAN RD
REC WHSE 57
TRACY CA 95304-5000
US
FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE
C20 AND CONTRACT
FREIGHT SHIPPING ADDRESS:
W62G2T
W1A8 DLA DIST SAN JOAQUIN
25600 S CHRISMAN ROAD
25600 S CHRISMAN RD REC WHSE 57
TRACY CA 95304-5000
US
Need Ship Date:02/02/2027 Original Required Delivery Date:04/18/2027
SPE7M2-26-T-6169 NSN/Part Number: 5310-01-515-8592 Quantity: 30 EA Purchase Request: 7017775423QTY: 30 Delivery: 165 days ADO