NUT, PLAIN, ROUND

NUT,PLAIN,ROUND
NUT, PLAIN, ROUND
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RQ006: QUALITY CONFORMANCE INSPECTION REQUIREMENTS
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
Certificate of Quality Compliance (CoQC) Contract Data Requirements Lists (CDRLs), DD Form 1423s, apply to this procurement. Review the Technical Data Package (TDP) for additional information. If CDRL-COQCCDRLs is missing from DLA Technical Data Management Transformation (TDMT) they can also be viewed in the DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
The following Contract Data Requirements Lists (CDRLs), DD Form 1423s, apply to this procurement. Review the Technical Data Package (TDP) for additional information. RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
RQ017: PHYSICAL IDENTIFICATION/BARE ITEM MARKING
Engineering Notes:
1. PART MARKING IAW MIL-STD-130, METHOD PER SAE AS478. BAG AND TAG PART.
2. DIMENSIONS AND TOLERANCES PER ASME Y14.5.
3. SURFACE TEXTURE PER ASME B46.1.
4. USE 4130 STEEL BAR/REFORGING STOCK PER SAE AMS-S-6758 IN LIEU OF MIL-S-6758.
5. CADMIUM PLATE PER SAE AMS-QQ-P-416 IN LIEU OF QQ-P-416.
6. MAGNETIC PARTICLE INSPECT PER ASTM E1444 IN LIEU OF MIL-I-6868 WITH THE FOLLOWING ADDITIONAL REQUIREMENT: THE INTENSITY OF VISIBLE LIGHT
SPE4A6-27-T-050J
SECTION B
REFERRED TO
IN PARAGRAPH 5.7.1 IS TO BE A MINIMUM OF 200FC.
7. HEAT TREAT STEEL PER SAE AMS-H-6875, CLASS A, SAE AMS 2759 AND SAE
AMS 2759/1
MAJOR CHARACTERISTICS: Characteristics (other than critical or minor), which, when defective, are likely to result in failure or to reduce the usability of the product or a major end item for its intended purpose. (Derived from MIL-STD-1916). MINOR CHARACTERISTICS: All characteristics not designated as critical or major but for which full conformity is required.
CRITICAL APPLICATION ITEM
TDP Rev A Gen 2 IAW BASIC DRAWING NR 82402 1650C247 REVISION NR C DTD 09/25/1957 PART PIECE NUMBER:
TDP Rev A Gen 2 IAW REFERENCE QAP 13873 CDRL-COQC-26210 REVISION NR DTD 12/04/2025 PART PIECE NUMBER:
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 7016196903 0001 EA 15.000
NSN/MATERIAL:5310008114357
DELIVERY (IN DAYS):0005
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: ORIGIN
ACCEPTANCE POINT: ORIGIN
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:10 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:00 CUSH/DUNN MAT:NA CUSH/DUNN THKNESS:C
UNIT CONT:BD OPI:O
INTRMDTE CONT:E5 INTRMDTE CONT QTY:AAA
PACK CODE:Q PACKING LEVEL: B
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:00 -00 No special marking
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
FREIGHT FORWARDER:
DPK002
SPE4A6-27-T-050J
SECTION B
PR: 7016196903 PRLI: 0001 CONT’D
EAGLE VAN LINES
16200 QUEENS CT
UPPER MARLBORO MD 20774
US
FREIGHT SHIPPING ADDRESS:
DPKU00
OFFICER COMMANDING
NO 101 AIR LOGISTICS CENTER
PAK BASE FAISAL
KARACHI
PK
MARKFOR
DPKU00
OFFICER COMMANDING
NO 101 AIR LOGISTICS CENTER
PAK BASE FAISAL
KARACHI
PK
M/F: (TCN) DPKU5V60137776
RDD: A01
PROJ: TP 1
SUPP ADD: DA2KCU SIG: L
FOR GOVERNMENT USE ONLY: (IPD) 02
DIC: A31 DIST: N01 ADV: FC: NL
Need Ship Date:00/00/0000 Original Required Delivery Date:04/08/2026
SPE4A6-27-T-050J NSN/Part Number: 5310-00-811-4357 Quantity: 15 EA Purchase Request: 7016196903QTY: 15 Delivery: 5 days ADO