This Solicitation opportunity from Department Of Defense was posted on August 10, 2026. The submission period has ended. Browse the details below for market research, or find similar active opportunities.
O-RING
Contract Overview
Solicitation details, issuing organization, response deadlines, documents, and interested companies for this government contract opportunity.
Active Opportunities Like This One
AI Contract Overview
The contract is for the procurement of 2,286 O-Rings, identified by NSN 5331-00-585-7725, under solicitation SPE7L1-26-T-948K issued by the Department of Defense’s Land Supply Chain. The item must conform to SAE AS28775A Revision A dated February 1, 2025, with part number MS28775-002 and is classified as a critical application item under TDP Rev A Gen 2. It is listed as a primary Qualified Products List or Qualified Manufacturers List item, meaning only suppliers on the approved list may qualify. All units must be manufactured to the current revision of the governing standard, and prior revisions are acceptable only for hardware produced before the solicitation date. The item is a Type I (Code Y) with a non-extendable shelf life of 180 months, requiring special marking code 32 and packaging per MIL-STD-2073-1E and MIL-STD-129, including sealing in a medium-duty, waterproof, greaseproof, opaque bag per MIL-DTL-117, Type II, Class C, Style 1 if exposed to UV. Packaging and palletization must adhere to DLA’s RP001 guidelines. The items must be free of asbestos and hexavalent chromium, and compliance with the Hazard Communication Standard (29 CFR 1910.1200) is mandatory for any hazardous materials. Sampling inspections must follow MIL-STD-1916, ASQ H1331 Table 1, or a comparable zero-based plan; critical, major, and minor attributes must be verified at levels VII, IV, and II or with AQLs of 0.1, 1.0, and 4.0 respectively. Zero non-conformances are required in sample lots if MIL-STD-105/ASQ Z1.4 is referenced. Delivery is due 109 days after receipt of order, to Tinker AFB, Oklahoma, under FOB Origin terms through the First Destination Transportation program. The contractor must submit a compliant Safety Data Sheet prior to award, and failure to do so disqualifies offerors. Electronic submissions via DIBBS are mandatory, with a closing date of August 21, 2026. Payment processing requires
General Info
Place of Performance
3301 F AVE CEN REC BLDG 506 DR 22, TINKER AFB, OK, 73145-8000, USASet-Aside
Timeline
Submission Closed
Organization & Contact Information
Full Description
O-RING
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RD003, COVERED DEFENSE INFORMATION POTENTIALLY APPLIES
THIS NSN IS LISTED AS A PRIMARY QPL OR QML
THEREFORE THE QUALIFIED PRODUCTS LIST OR
QUALIFIED MANUFACTURERS LIST IS APPLICABLE.
THIS ITEM IS DEFINED BY EITHER BY A MILITARY PART STANDARD, OR A PART
STANDARD PUBLISHED BY A CONSENSUS NON-GOVERNMENT STANDARDS ORGANIZATION.
HARDWARE MANUFACTURED TO THE CURRENT REVISION OF THE PART STANDARD
DEFINING THIS ITEM IS ACCEPTABLE.
HARDWARE MANUFACTURED IN THE PAST TO A PREVIOUS, BUT THEN CURRENT,
REVISION OF THE STANDARD IS ACCEPTABLE.
ANY HARDWARE MANUFACTURED FROM THE DATE OF THIS SOLICITATION FORWARD,
SHALL BE MANUFACTURED IN ACCORDANCE WITH THE CURRENT REVISION OF THE
PART STANDARD IN QUESTION.
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
RS039: Shelf-life requirement RS001 for a TYPE I (CODE Y) item with a shelf life of 180 months (non-extendable) applies to this item.
SPE7L1-26-T-948K
SECTION B
"ITEMS SUPPLIED MUST BE FREE OF ASBESTOS.
LISTED CODE AND PART NUMBERS CONTAINING ASBESTOS
ARE NO LONGER ACCEPTABLE, AND ANY ALTERNATIVE
ITEM/MATERIAL MUST BE APPROVED IN ACCORDANCE
WITH CLAUSE L30 AND PROVISION 4 CONDITIONS
FOR NSN/Part Number: 5331-00-585-7725 Quantity: 2,286 EA Purchase Request: 7017780476QTY: 2286 Delivery: 109 days ADO
More opportunities from Department Of Defense → LAND SUPPLY CHAIN
Same awarding agency
Earlier notices in this NAICS code
Posted before this notice, open and closed
Find Active Opportunities Like This
Get AI-powered intelligence on the opportunities still open
Every page of the solicitation package shredded into a compliance breakdown
AI-powered matching based on your capabilities and past performance
Competitor and incumbent history on the requirement
Automated alerts on amendments, Q&A deadlines, and award
Join 750+ contractors already using CLEATUS