This Solicitation opportunity from Department Of Defense was posted on July 29, 2026. The submission period has ended. Browse the details below for market research, or find similar active opportunities.
PIN-RIVET
Contract Overview
Solicitation details, issuing organization, response deadlines, documents, and interested companies for this government contract opportunity.
Active Opportunities Like This One
AI Contract Overview
The contract pertains to the procurement of 110 PIN-RIVET units identified by NSN 5320-00-401-5711 under solicitation SPE4A6-26-T-10HV, with a delivery requirement of 277 days after contract award. Technical and quality requirements are governed by the DLA Master List of Technical and Quality Requirements, which incorporates referenced standards such as MIL-STD-1916 and ASQ H1331 for sampling, mandating zero non-conformances unless otherwise specified. Critical and major attributes must be verified at designated levels or AQLs, and all Class 3A and 3B threads must be gaged in compliance with SAE AS8879 or MIL-S-7742, excluding self-locking nuts and threads below specified diameters. The item is subject to strict export controls under ITAR or EAR, prohibiting any export or disclosure to foreign persons without prior authorization from the Department of State or Commerce, with DFARS 252.225-7048 applying to all technical data. Access to this controlled data is restricted to contractors with approved US/Canada Joint Certification Program certification, completed DOD export control training, and formal DLA approval. Packaging, identification, and documentation requirements are enforced per DLA directives including removal of government markings from non-accepted items and bare item marking. Inspection and acceptance must occur at the manufacturer's origin, and source approval documentation must be submitted as required. The contract is managed by the Department of Defense’s ASC Commodities Division with performance located at Robins Air Force Base, and all responses are due by August 6, 2026.
General Info
Agency
NAICS
Place of Performance
BLDG 376, ROBINS A F B, GA, 31098-1887, USASet-Aside
Timeline
Submission Closed
Organization & Contact Information
Full Description
PIN-RIVET
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RQ017: PHYSICAL INDENTIFICATION/BARE ITEM MARKING
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
ALL CLASS 3A AND 3B THREADS SHALL BE GAGED
I/A/W CATEGORY 1 PER SAE AS8879 OR "SAFETY
CRITICAL THREADS" PER MIL-S-7742 UNLESS
OTHERWISE SPECIFIED. THE ABOVE EXCLUDES
SELF-LOCKING NUTS AND INTERNAL THREADS SMALLER
THAN .190 DIA. AND EXTERNAL THREADS SMALLER
THAN .138 DIA.
RC001: DOCUMENTATION REQUIREMENTS FOR SOURCE APPROVAL REQUEST (SAR)
RD002, COVERED DEFENSE INFORMATION APPLIES
RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS
(MANUFACTURERS AND NON-MANUFACTURERS)
RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN
RQ032: EXPORT CONTROL OF TECHNICAL DATA
This item has technical data some or all of which is subject to export-control of either the International Traffic in Arms regulations (ITAR) or the Export Administration Regulations (EAR), and cannot be
SPE4A6-26-T-10HV
SECTION B
exported without prior authorization from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and nationals whether located in the United States or abroad. This requirement applies equally to foreign national employees and U.S. companies and their foreign subsidiaries. DFARS 252.225-7048 is applicable to this data.
The Defense Logistics Agency (DLA) limits distribution of export-control technical data to DLA contractors that have an approved US/Canada Joint Certification Program (JCP) certification, have completed the Introduction to Proper Handling of DOD Export-Controlled Technical Data Training and the DLA Export-Controlled Technical Data Questionnaire (both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. NSN/Part Number: 5320-00-401-5711 Quantity: 110 EA Purchase Request: 7016474153QTY: 110 Delivery: 277 days ADO
More opportunities from Department Of Defense → ASC COMMODITIES DIVISION
Same awarding agency
Find Active Opportunities Like This
Get AI-powered intelligence on the opportunities still open
Every page of the solicitation package shredded into a compliance breakdown
AI-powered matching based on your capabilities and past performance
Competitor and incumbent history on the requirement
Automated alerts on amendments, Q&A deadlines, and award
Join 650+ contractors already using CLEATUS