PIPE, EXHAUST

PIPE,EXHAUST
PIPE<(>,<)> EXHAUST
.
DEMIL #C# = USML ITEMS MUTILATION TO THE
POINT OF SCRAP REQUIRED WORLDWIDE.
.
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
.
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
.
RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS
(MANUFACTURERS AND NON-MANUFACTURERS)
.
RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN
.
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
.
CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE
USED NOR INCORPORATED IN ANY ITEMS TO BE
DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION
SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT
DOES NOT ALLEVIATE ANY PRODUCT REQUIREMENTS.
SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR
APPROVAL UNLESS THEY ARE AUTHORIZED BY THE
SPECIFICATION REQUIREMENTS.
.
"ANY ITEM PREVIOUSLY TESTED BY A VENDOR
IN ACCORDANCE WITH QUALIFICATION
REQUIREMENTS (FOR EXAMPLE: FAT, HIGH
SHOCK AND/OR VIBRATION TEST), STATED ON
DWG, SPECIFICATION, OR STANDARD MAY NOT
REQUIRE FURTHER TESTING BY THE SAME VENDOR
EXCEPT FOR A LATER CHANGE IN DESIGN,
MANUFACTURING PROCEDURES, OR TESTING
REQUIREMENTS. A CERTIFICATION OF
CONFORMANCE WITH PREVIOUS TEST RESULTS
ATTESTING APPLICABILITY SHALL BE
SUBMITTED FOR ITEMS PREVIOUSLY TESTED."
.
RQ016: COMPONENT QUALIFIED PRODUCTS LISTS (QPL)/QUALIFIED MANUFACTURERS
LISTS (QML). THIS ITEM CONTAINS ONE OR MORE COMPONENTS DEFINED BY A
SPECIFICATION(S) WITH AN ASSOCIATED QUALIFIED PRODUCTS LIST (QPL) OR
QUALIFIED MANUFACTURERS LIST (QML). QUALIFICATION REQUIREMENTS IN
PROCUREMENT NOTE H02 "COMPONENT QUALIFIED PRODUCTS LIST (QPL)/QUALIFIED
SPE7L4-26-T-7177
SECTION B
MANUFACTURERS LIST (QML)" APPLY.
.
RT001: MEASURING AND TEST EQUIPMENT
.
THE ITEM DESCRIBED IN THIS SOLICITATION
IS DEFINED IN WHOLE OR IN PART BY ARMY
DRAWING(S). THESE DRAWING(S) MAY CONTAIN
A PAINT FINISHING REQUIREMENT. WHERE SUCH
REQUIREMENTS ARE SPECIFIED, USE DCSC DRAWING
16236 CS-2300-0001 IN LIEU OF FINISH REQUIRE
MENTS OF THE ARMY DRAWING(S). THIS DRAWING
CONTAINS SPECIFICATIONS FOR CHEMICAL AGENT
RESISTANT COATINGS (CARC), AND ADDITIONAL
INFORMATION RELATING TO HIGH TEMPERATURE
COATINGS.
.
.
NOTICE: SUPPLIERS ARE REQUIRED TO IDENTIFY SUBCONTRACTORS
AT TIME OF QUOTING IF KNOWN. USE OF ANY SUB-CONTRACTOR
SUPPLIER WILL REQUIRE JCP CERTIFICATION APPROVAL.
RQ032: EXPORT CONTROL OF TECHNICAL DATA
This item has technical data some or all of which is subject to export-control of either the International Traffic in Arms regulations (ITAR) or the Export Administration Regulations (EAR), and cannot be exported without prior authorization from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and nationals whether located in the United States or abroad. This requirement applies equally to foreign national employees and U.S. companies and their foreign subsidiaries. DFARS 252.225-7048 is applicable to this data.
The Defense Logistics Agency (DLA) limits distribution of export-control technical data to DLA contractors that have an approved US/Canada Joint Certification Program (JCP) certification, have completed the Introduction to Proper Handling of DOD Export-Controlled Technical Data Training and the DLA Export-Controlled Technical Data Questionnaire (both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. NSN/Part Number: 2540-01-470-5964 Quantity: 28 EA Purchase Request: 7018496768QTY: 28 Delivery: 81 days ADO