PRODUCTION LOT TESTING

FLANGE,PIPE
FLANGE, PIPE 90/10 CUNI MATERIAL, 2 INCH
NOMINAL PIPE SIZE, SOCKET-WELD, 150 PSI, EXCEPT
USE MIL-PRF-20042 IN LIEU OF MIL-F-20042 AND
REFERENCE TO PARAGRAPH 7.3 ON DRAWING 810
4715319 FOR SPOT FACING AND AND ALTERNATE BACK
FACING, MSS SP-9 TO BE USED FOR SPOT FACING AND
BACK FACING REQUIREMENTS.
BOLT CIRCLE DIAMETER
4.438 INCHES NOMINAL
FLANGE DIAMETER
5.563 INCHES NOMINAL
THICKNESS
0.438 INCHES NOMINAL
SOCKET DIAMETER
2.411 INCHES NOMINAL
BORE DIAMETER
2.240 INCHES NOMINAL
BOLT HOLE DIAMETER
0.562 INCHES NOMINAL
FLANGE SECTION STYLE
PLAIN FACE, SOCKET BRAZING NECK W/O BRAZING RING
FACE SEATING SURFACE CONDITION
MACHINED
MAXIMUM OPERATING PRESSURE A ND MEDIA FOR WHICH DESIGNED ARE 150 POUNDS
SQUARE INCH AND GAS, WATER AND OIL
COPPER ALLOY
ROUND, ONE BOLT CIRCLE.
contractors may allow spot face dimensioning to MSS SP-9 for characteristic 3, or the dimensioning adjustments Referenced in Section B of contract. DCMA must inspect at least sample of characteristic 3 to ensure does not get too out of tolerance with provisions.
SAMPLING: THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION, STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
RD005: Cybersecurity Maturity Model Certification (CMMC) Level 2 Certified Third-Party Assessment Organization (C3PAO)
RD002, COVERED DEFENSE INFORMATION APPLIES
0.438 INCHES NOMINAL
5.563 INCHES NOMINAL
PRODUCTION LOT TESTING REQUIRED IAW SQAP00-471-5319.
A metal casting process was identified as a means to manufacture this item. Tooling is required to produce a casting. For sourcing, tooling,
SPE7M1-26-T-282C
SECTION B
materials or other information, please contact the appropriate assistance team: (Aviation, C<(>&<)>E Supply Chains) https://www.dla.mil/Aviation/Offers/Engineering/Forging-and-Casting/; (Land & Maritime Supply Chains) DSCC.cast.forge@dla.mil.
RQ032: EXPORT CONTROL OF TECHNICAL DATA
This item has technical data some or all of which is subject to export-control of either the International Traffic in Arms regulations (ITAR) or the Export Administration Regulations (EAR), and cannot be exported without prior authorization from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and nationals whether located in the United States or abroad. This requirement applies equally to foreign national employees and U.S. companies and their foreign subsidiaries. DFARS 252.225-7048 is applicable to this data.
The Defense Logistics Agency (DLA) limits distribution of export-control technical data to DLA contractors that have an approved US/Canada Joint Certification Program (JCP) certification, have completed the Introduction to Proper Handling of DOD Export-Controlled Technical Data Training and the DLA Export-Controlled Technical Data Questionnaire (both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. NSN/Part Number: 0001S00000061 Quantity: 17 EA Purchase Request: 7015535308QTY - See Solicitation Delivery: 259 days ADO