Repair and Calibration of Multiple Fluke Units

This is a combined synopsis/solicitation for commercial items prepared in accordance with the format in Subpart 12.6, as supplemented with additional information included in this notice. This announcement constitutes the only solicitation; proposals are being requested and a written solicitation will not be issued. Solicitation number W31P4Q-18-Q-0075 is issued as a request for quotation (RFQ). The Government reserves the right to award without discussions. The solicitation document and incorporated provisions and clauses are in effect through the Federal Acquisition Circular 2005-80. The requirement is not a set aside. The associated NAICS code is 334513. The small business size standard is 750 employees. Description of the requirement is as follows: Solicitation is issued as a request for a Firm Fixed Price quote for the repair and calibration of three items of equipment, manufactured by Fluke Electronics Corporation, Everett, WA. US Army Contracting Command, Redstone Arsenal, intends to issue a sole source contract to the original equipment manufacturer, Fluke Electronics Corporation. The statutory authority allowing for solicitation to a single source for this requirement is 10 U.S.C. 2304 (g)(1)(A), as implemented by Federal Acquisition Regulation (FAR) 13.106-1(b)(1) titled - Soliciting from a single source and no other supplies or services will satisfy agency requirement. The Government intends to use the policies and procedures of FAR Part 12 in conjunction with those at FAR Part 13 for this effort. The place of inspection and acceptance is W80RA6. FOB is at Destination. Shipping Address is as follows: (Standard commercial packaging and shipping is sufficient for this requirement) CLIN 0001: W80KFZ U.S. Army TMDE Support Center - Letterkenny Attention: Mr. Miguel Vasquez Building 5240, Technology Lane Chambersburg, PA 17201 CLIN 0002 & 0003: W80RA6 U.S. Army TMDE Support Activity Attention: Mr. Van Allen Building 5435, Fowler Road Redstone Arsenal, AL 35898-5000 Period of Performance: The contractor shall repair and calibrate the item(s) of equipment, and ship back to the customer in not more than 30 days from the date of contract award. Earlier return delivery is desired if at no additional cost to the government. CLIN Structure is as follows: CLIN 0001 Calibrate & Repair, Sensor Head, Fluke Model 9530, Serial No. 209665226 (per attached PWS) Quantity 1 ea. CLIN 0002 Calibrate & Repair, RF Reference Source, Fluke Model 9640A-LPN, Serial No. 934954121(per attached PWS) Quantity 1 ea. CLIN 0003 Calibrate & Repair, Multifunction Calibrator, Fluke Model 5700A/EP3, Serial No. 5370006 (per attached PWS) Quantity 1 ea. CLIN 0004 Contract Manpower Reporting (per attached PWS), Quantity 1 ea. Provision at 52.212-1, Instructions to Offerors - Commercial Items, applies to this acquisition and any addenda to the provision also apply. Provision at 52.212-2, Evaluation - Commercial Items, is applicable. The lowest price technically acceptable is the sole evaluation factor. Non cost factors are of equal importance to price. Offerors shall include a completed copy of the provision 52.212-3, Offeror Representations and Certifications - Commercial Items. Clause 52.212-4, Contract Terms and Conditions - Commercial Items, applies to this acquisition and any addenda to the provision also apply. Clause at 52.212-5 Contract Terms and Conditions - Required to Implement Statutes or Executive Orders - Commercial Items, also applies to this acquisition and additional FAR clauses may be cited as needed. Terms and conditions for this requirement are consistent with customary commercial practices. Contract financing is not authorized. Payment shall be made through Wide Area Work Flow (WAWF), in Accordance with DFARS 252.232-7006. DFARS 252.232-7003 - Electronic Submission of Payment Requests and Receiving Reports and Instructions. Payment method shall be through Wide Area Work Flow. This a DPAS DO rated order. Oral Communications are not acceptable in response to this notice. All responsible sources may submit an offer which shall be considered by the Agency. Quotes are due no later than 22 May 2018. EVALUATION FACTORS: The Contractor's proposal must be determined to be acceptable in terms of the following: (a) Price reasonableness. (b) Technical compliance with the PWS (to include compliance with accredited calibration - Z540 traceable, with data). (c) Use of original equipment manufacturer parts only, when required. (d) Ability to implement Fluke proprietary software or firmware upgrades per manufacturer's recommended schedule, when required. Quotes shall be submitted by email only to maggie.g.bevis.civ@mail.mil. Other electronic or hard copy submissions are not authorized. QUOTES/OFFERS RECEIVED AFTER THE SPECIFIED DUE DATE AND TIME WILL NOT BE CONSIDERED FOR AWARD. For further information regarding this solicitation, contact Maggie Bevis, 256-876-5209, email maggie.g.bevis.civ@mail.mil or Adrian Epps, 256-876-4912, email adrian.l.epps.civ@mail.mil.