RESISTOR NETWORK, FIXED

RESISTOR NETWORK,FIXED,FILM
RESISTOR NETWORK,FI
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RQ017: PHYSICAL IDENTIFICATION/BARE ITEM MARKING
THIS ITEM IS IDENTIFIED AS A COMMERCIAL ITEM (TO INCLUDE 'COMMERCIAL
OF A TYPE')
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
CRITICAL APPLICATION ITEM
VISHAY DALE ELECTRONICS, LLC 91637 P/N MSP08A-00-S254
TECHNO COMPONENTS CORP DBA TECHNO 17826 P/N TCX0164-11
LINE ITEM 0000000001 TYPE OF COVERAGE: DLA DIRECT, CONUS
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 1000242726 0001 EA 149.000
SPE7M1-26-U-5903
SECTION B
PR: 1000242726 PRLI: 0001 CONT’D
This is an estimated quantity and may not be purchased by the IDC.
NSN/MATERIAL:5905013375934
DELIVERY (IN DAYS):0052
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: DESTINATION
ACCEPTANCE POINT: DESTINATION
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E QUP:001 PRES MTHD:ZZ CLNG/DRY:1 PRESV MAT:ZZ WRAP MAT:ZZ CUSH/DUNN MAT:ZZ CUSH/DUNN THKNESS:C UNIT CONT:ZZ OPI:M INTRMDTE CONT:ZZ INTRMDTE CONT QTY:AAA PACK CODE:U MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129. SPECIAL MARKING CODE:ZZ -ZZ Special Requirements
UNIT PACKAGE MARKING REQUIREMENT FOR COMPONENT LEAD FINISH
(a) In addition to all other marking requirements in this contract, the Contractor shall apply one of the assigned markings in accordance with paragraphs 5.3.1 and 5.3.2 of IPC/JEDEC J-STD-609, Marking and Labeling of Components, printed circuit boards (PCBs) and printed circuit board assemblies (PCBAs) to Identify Lead (Pb), Pb-Free and Other Attributes, to each individual unit pack of the item being acquired. Placement of the markings shall be in accordance with paragraph 6.2 of the standard.
(b) Copies of the current version of this standard may be purchased or downloaded from the Association Connecting Electronics Industry (IPC), http://www.ipc.org, http://www.ipc.org, or the Solid State Technology Association (JEDEC), http://www.jedec.org. http://www.jedec.org.
PRESERVATION AND PACKAGING SHALL BE IAW THE LATEST REVISION OF MILITARY SPECIFICATION: MIL-DTL-39032, FOR RESISTORS. UNIT PACKAGE MARKING REQUIREMENT FOR COMPONENT LEAD FINISH
(a) In addition to all other marking requirements in this contract, the Contractor shall apply one of the assigned markings in accordance with paragraphs 5.3.1 and 5.3.2 of IPC/JEDEC J-STD-609, Marking and Labeling of Components, printed circuit boards (PCBs) and printed circuit board assemblies (PCBAs) to Identify Lead (Pb), Pb-Free and Other Attributes, to each individual unit pack of the item being acquired. Placement of the markings shall be in accordance with paragraph 6.2 of the standard.
(b) Copies of the current version of this standard may be purchased or downloaded from the Association Connecting Electronics Industry (IPC), http://www.ipc.org, http://www.ipc.org, or the Solid State Technology Association (JEDEC), http://www.jedec.org. http://www.jedec.org.

SPE7M1-26-U-5903 NSN/Part Number: 5905-01-337-5934 Quantity: 149 EA Purchase Request: 1000242726QTY: 149 Delivery: 52 days ADO