This Solicitation opportunity from Department Of Defense was posted on July 14, 2026. The submission period has ended. Browse the details below for market research, or find similar active opportunities.
RIVET, BLIND
Contract Overview
Solicitation details, issuing organization, response deadlines, documents, and interested companies for this government contract opportunity.
Active Opportunities Like This One
AI Contract Overview
This contract specifies the procurement of 27,232 blind rivets under NSN 5320-01-143-5078, identified as a commercial item with no preference for lock type, meaning both visible and internal lock rivets are acceptable. The rivets must comply with the current revision of the applicable part standard, NAS9301 Revision 7 or NAS1686 Revision 5, and hardware manufactured to prior revisions that were current at the time of production remains acceptable as long as it meets all requirements. Quality assurance follows MIL-STD-1916 or ASQ H1331 Table 1 with zero non-conformances required in sample lots unless otherwise directed, and attributes are assigned verification levels VII, IV, and II for critical, major, and minor characteristics respectively. All items are subject to the DLA Master List of Technical and Quality Requirements, which take precedence over other standards. Manufacturing must be performed by qualified suppliers whose data is published in referenced military handbooks. The items must be packaged in compliance with ASTM D3951 and marked and labeled per MIL-STD-129, with palletization adhering to DLA packaging requirements. Delivery is FOB origin with a required delivery date of March 5, 2027, and a need ship date of June 8, 2026, allowing for a 104-day delivery period. Inspection and acceptance occur at the destination, with zero tolerance for quantity variance. The unit of issue is each, and all packaging and labeling must reflect the specified QUP. Transportation instructions follow DLAD Proc Note C19 and C20. The contract is issued by the Department of Defense’s ASC Commodities Division, with Debra Fowler as the primary point of contact, and the order is solicited under SPE4A6-26-T-05XL, classified under NAICS Code 332510.
General Info
Agency
NAICS
Place of Performance
3301 F AVE CEN REC BLDG 506 DR 22, TINKER AFB, OK, 73145-8000, USASet-Aside
Timeline
Submission Closed
Organization & Contact Information
Full Description
RIVET,BLIND
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
THIS ITEM IS IDENTIFIED AS A COMMERCIAL ITEM (TO INCLUDE 'COMMERCIAL
OF A TYPE')
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
THIS ITEM IS DEFINED BY EITHER BY A MILITARY PART STANDARD, OR A PART
STANDARD PUBLISHED BY A CONSENSUS NON-GOVERNMENT STANDARDS ORGANIZATION.
HARDWARE MANUFACTURED TO THE CURRENT REVISION OF THE PART STANDARD
DEFINING THIS ITEM IS ACCEPTABLE.
HARDWARE MANUFACTURED IN THE PAST TO A PREVIOUS, BUT THEN CURRENT,
REVISION OF THE STANDARD IS ACCEPTABLE.
ANY HARDWARE MANUFACTURED FROM THE DATE OF THIS SOLICITATION FORWARD,
SHALL BE MANUFACTURED IN ACCORDANCE WITH THE CURRENT REVISION OF THE
PART STANDARD IN QUESTION.
FOR ITEMS LISTED IN MIL-HDBK-5J/MMPDS-01,
JOINT ALLOWABLE REQUIREMENTS APPLY.
********************************************
QUALIFIED SUPPLIERS CAN ONLY PROVIDE PARTS FROM
MANUFACTURERS WHOSE DATA HAS BEEN ACCEPTED FOR
PUBLICATION IN THAT REFERENCE.
"NS" LETTERS AFTER THE MATERIAL CODE INDICATE NO
PREFERENCE TO LOCK TYPE (MAY BE VISIBLE OR
INTERNAL). RIVETS WITH NO LETTER CODE AFTER THE
MATERIAL CODE (INDICATING VISIBLE LOCK) AND
RIVETS WITH THE LETTER "H" AFTER THE MATERIAL
CODE (INDICATING INTERNAL LOCK) ARE BOTH
ACCEPTABLE FOR THIS ITEM OF SUPPLY.
SPE4A6-26-T-05XL
SECTION B
RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS
(MANUFACTURERS AND NON-MANUFACTURERS)
RQ017: PHYSICAL INDENTIFICATION/BARE ITEM MARKING
CRITICAL APPLICATION ITEM
TDP Rev D Gen 4 IAW BASIC NON GOVT STD NAS9301 REVISION NR 7 DTD 03/31/2020 PART PIECE NUMBER: STD P/N BNS-4-01
TDP Rev D Gen 4 IAW REFERENCE NON GOVT STD NAS1686 REVISION NR 5 DTD 04/30/2026 PART PIECE NUMBER:
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 7017487156 0001 EA 27,232.000
NSN/MATERIAL:5320011435078
DELIVERY (IN DAYS):0104
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: DESTINATION
ACCEPTANCE POINT: DESTINATION
PREP FOR DELIVERY:
PKGING DATA-QUP:050
WILL BE PACKAGED IN ACCORDANCE WITH ASTM D3951.
All DLA Master List of Technical and Quality Requirements take precedence over ASTM D3951. Mark and label all packaging and packing in accordance with MIL-STD-129. The Unit of Issue (U/I) and Quantity per Unit Pack (QUP) will be as specified in the contract/purchase order. PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
PARCEL POST ADDRESS:
SW3211
DLA DISTRIBUTION DEPOT OKLAHOMA
3301 F AVE CEN REC BLDG 506 DR 22
TINKER AFB OK 73145-8000
SPE4A6-26-T-05XL
SECTION B
PR: 7017487156 PRLI: 0001 CONT’D
US
FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE
C20 AND CONTRACT
FREIGHT SHIPPING ADDRESS:
SW3211
DLA DISTRIBUTION DEPOT OKLAHOMA
3301 F AVE CEN REC BLDG 506 DR 22
TINKER AFB OK 73145-8000
US
Need Ship Date:06/08/2026 Original Required Delivery Date:03/05/2027
SPE4A6-26-T-05XL NSN/Part Number: 5320-01-143-5078 Quantity: 27,232 EA Purchase Request: 7017487156QTY: 27232 Delivery: 104 days ADO
More opportunities from Department Of Defense → ASC COMMODITIES DIVISION
Same awarding agency
Find Active Opportunities Like This
Get AI-powered intelligence on the opportunities still open
Every page of the solicitation package shredded into a compliance breakdown
AI-powered matching based on your capabilities and past performance
Competitor and incumbent history on the requirement
Automated alerts on amendments, Q&A deadlines, and award
Join 650+ contractors already using CLEATUS