This Solicitation opportunity from Department Of Defense was posted on May 22, 2026. The submission period has ended. Browse the details below for market research, or find similar active opportunities.
RIVET, BLIND
Contract Overview
Solicitation details, issuing organization, response deadlines, documents, and interested companies for this government contract opportunity.
Active Opportunities Like This One
AI Contract Overview
The contract solicitation SPE4A6-26-T-57V7 seeks the procurement of 10 blind rivets identified by NSN 5320-00-113-1665 under a fully competitive acquisition governed by military and federal standards. The item must be manufactured to the current revision of its defining part standard, whether military or consensus non-government, with legacy hardware produced to prior but then-current revisions still acceptable, provided all deliveries from the solicitation date forward adhere strictly to the latest standard. Technical and quality requirements are defined by the DLA Master List of Technical and Quality Requirements, referenced via R and I codes including RQ001 for tailored quality requirements, RQ009 for inspection and acceptance at origin, RQ011 for removal of government identification from non-accepted supplies, and RQ017 for physical identification and bare item marking. Sampling and inspection procedures must follow MIL-STD-1916, ASQ H1331 Table 1, or an equivalent zero-based sampling plan, with acceptance requiring zero non-conformances if MIL-STD-105/ASQ Z1.4 is used for lot sizing. Attributes are classified as critical (AQL 0.1 or Verification Level VII), major (AQL 1.0 or Verification Level IV), or minor (AQL 4.0 or Verification Level II), with unspecified attributes treated as major. The manufacturer’s quality system must meet at least SAE AS9003 or ISO 9001 tailored to SAE AS9003 requirements, and certificates of conformance under FAR 52.246-15 are authorized unless overridden by a Quality Assurance Letter of Instruction. Origin inspection is mandatory, and source inspection is required due to the item’s critical classification. Packaging, labeling, and marking must fully comply with MIL-STD-129 for shipment and storage, MIL-STD-130N for identification of U.S. military property, and RP001 for DLA packaging requirements, with palletization following these same standards. Packaging material must meet ASTM D3951 unless superseded by higher-priority DLA requirements. Delivery is FOB destination to the DLA Distribution Depot Oklahoma at Tinker AFB, with a 106-day lead time from receipt of order, and the contract requires full compliance with WAWF for invoicing and receiving reports using
General Info
Agency
NAICS
Place of Performance
3301 F AVE CEN REC BLDG 506 DR 22, TINKER AFB, OK, 73145-8000, USASet-Aside
Timeline
Submission Closed
Organization & Contact Information
Full Description
RIVET,BLIND
RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN
RQ017: PHYSICAL INDENTIFICATION/BARE ITEM MARKING
CERTIFICATE OF CONFORMANCE PROCEDURES (FAR 52.246-15) ARE AUTHORIZED,
UNLESS WITHELD BY A QUALITY ASSURANCE LETTER OF INSTRUCTION.
RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS
(MANUFACTURERS AND NON-MANUFACTURERS)
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
THIS ITEM IS DEFINED BY EITHER BY A MILITARY PART STANDARD, OR A PART
STANDARD PUBLISHED BY A CONSENSUS NON-GOVERNMENT STANDARDS ORGANIZATION.
HARDWARE MANUFACTURED TO THE CURRENT REVISION OF THE PART STANDARD
DEFINING THIS ITEM IS ACCEPTABLE.
HARDWARE MANUFACTURED IN THE PAST TO A PREVIOUS, BUT THEN CURRENT,
REVISION OF THE STANDARD IS ACCEPTABLE.
ANY HARDWARE MANUFACTURED FROM THE DATE OF THIS SOLICITATION FORWARD,
SHALL BE MANUFACTURED IN ACCORDANCE WITH THE CURRENT REVISION OF THE
PART STANDARD IN QUESTION.
SPE4A6-26-T-57V7
SECTION B
IDENTIFY TO:
MIL-STD-130N, 16 Nov 2012 IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY THIS NSN IS PROCURED AS FULLY COMPETITIVE IN ACCORDANCE WITH A MILITARY / FEDERAL SPECIFICATION/STANDARD. SEE NSN/Part Number: 5320-00-113-1665 Quantity: 10 HD Purchase Request: 7011191228QTY: 10 Delivery: 106 days ADO
More opportunities from Department Of Defense → ASC COMMODITIES DIVISION
Same awarding agency
Find Active Opportunities Like This
Get AI-powered intelligence on the opportunities still open
Every page of the solicitation package shredded into a compliance breakdown
AI-powered matching based on your capabilities and past performance
Competitor and incumbent history on the requirement
Automated alerts on amendments, Q&A deadlines, and award
Join 650+ contractors already using CLEATUS