SCREW, CAP, HEXAGON HEAD

SCREW,CAP,HEXAGON HEAD
SCREW, CAP, HEXAGON HEAD
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS
(MANUFACTURERS AND NON-MANUFACTURERS)
RQ006: QUALITY CONFORMANCE INSPECTION REQUIREMENTS
RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
ITEM SURFACE MARKING REQUIREMENT: MATERIAL SYMBOL, MANUFACTURER'S SYMBOL
AND LOT NUMBER ARE REQUIRED AND SHALL BE APPLIED DIRECTLY TO THE SURFACE
OF THIS ITEM IN ACCORDANCE WITH MIL-DTL-1222. MATERIAL SYMBOL SHALL BE
IN ACCORDANCE WITH THE "ADDITIONAL REQUIREMENTS" COLUMN OF MIL-DTL-1222
TABLE I. LOCATION OF MARKINGS SHALL IN ACCORDANCE WITH MIL-DTL-1222J
PARA. 3.13.2.
THE MANUFACTURER'S SYMBOL (LOGO) MUST BE LISTED IN MIL-HDBK-57. FOR
FASTENERS LESS THAN 1/2 INCH DIAMETER, IF ALL REQUIRED MARKINGS CANNOT
BE APPLIED DUE TO SPACE LIMITATIONS, THE MARKINGS SHALL BE APPLIED IN
THE FOLLOWING ORDER OF PRECEDENCE: MATERIAL SYMBOL, MANUFACTURER'S
SYMBOL AND LOT NUMBER. MARKINGS NOT INCLUDED ON THE BARE ITEM SHALL BE
PLACED ON PACKAGING LABELS.
FOR MANUFACTURER'S SYMBOL INFORMATION AND INQUIRIES PLEASE VISIT THE
MIL-HDBK-57 URL AT:
https://www.troopsupport.dla.mil/Hardware/Technical/logoreg.asp
MERCURY OR MERCURY CONTAINING COMPOUNDS SHALL
NOT BE INTENTIONALLY ADDED TO<(>,<)> OR COME IN DIRECT
CONTACT WITH<(>,<)> ANY HARDWARE OR SUPPLIES FURNISHED
UNDER THIS CONTRACT. EXCEPTION: FUNCTIONAL MERCURY
USED IN BATTERIES, FLUORESCENT LIGHTS, REQUIRED
INSTRUMENTS; SENSORS OR CONTROLS; WEAPON SYSTEMS;
AND CHEMICAL ANALYSIS REAGENTS SPECIFIED BY NAVSEA.
PORTABLE FLUORESCENT LAMPS AND PORTABLE INSTRUMENTS
CONTAINING MERCURY SHALL BE SHOCK PROOF AND CONTAIN
A SECOND BOUNDARY OF CONTAINMENT OF THE MERCURY OR
MERCURY COMPOUND. (IAW NAVSEA 5100-003D).
SPE4A6-26-T-22FT
SECTION B
The following Contract Data Requirements Lists (CDRLs), DD Form 1423s, apply to this procurement. Review the Technical Data Package (TDP) for additional information. Certificate of Quality Compliance (CoQC) Contract Data Requirements Lists (CDRLs), DD Form 1423s, apply to this procurement. Review the Technical Data Package (TDP) for additional information. If CDRL-COQCCDRLs is missing from DLA Technical Data Management Transformation (TDMT) they can also be viewed in the DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
A Certificate of Quality Compliance (Mill-Material Certification) is required. A copy of the Certificate of Quality Compliance shall be provided with every shipment to the customer or DLA depot, and a copy of the Certificate of Quality Compliance provided for each shipment shall be forwarded to the DLA Troop Support Contracting Officer identified on the award.
CRITICAL ITEM SOURCE INSPECTION REQUIRED.
THE DRAWING(S) LISTED BELOW ARE AVAILABLE AT DLA DURING "OPEN SOLICITATION ONLY". TO RECEIVE A COPY OF THE DRAWING(S)<(>,<)> FOR EBS SOLICITATIONS USE URL HTTPS://WWW.DIBBS.BSM.DLA.MIL/RFQ/
PRODUCT VERIFICATION TESTING (PVT) IS MANDATORY
ITEMS SUPPLIED UNDER THIS NSN SHALL MEET ALL REQUIRED ASPECTS OF
MIL-DTL-1222J, INCLUDING BUT NOT LIMITED TO: MANUFACTURING PROCESSES,
MECHANICAL PROPERTIES, MARKINGS, INSPECTIONS AND EVALUATIONS
ACQUISITION REQUIREMENTS:
DOCUMENT: MIL-DTL-1222J, 08 DECEMBER 2000, GENERAL SPECIFICATION FOR
STUDS, BOLTS, SCREWS AND NUTS FOR APPLICATIONS WHERE A HIGH DEGREE OF
RELIABILITY IS REQUIRED
ITEM CONFIGURATION: PART NUMBER M1222RX10C232NANN PER APPENDIX OF
MIL-DTL-1222J; TYPE I HEX HEAD CAP SCREW, 5/8-11 UNC-2A, 2.00 INCH
NOMINAL LENGTH OVERALL. DIMENSIONS SHALL BE IN ACCORDANCE WITH ASME
B18.2.1
MATERIAL: SHALL BE NICKEL ALLOY 400 GRADE PER TABLE II OF MIL-DTL-1222J
VERIFICATION OF CONFORMANCE SHALL BE IN ACCORDANCE WITH SECTION 4 OF
MIL-DTL-1222J
PRODUCT VERIFICATION TESTING (PVT) WILL BE PERFORMED PRIOR TO ACCEPTANCE
OF EACH SHIPMENT.
PRODUCT VERIFICATION TESTING (PVT) PROCUREMENT NOTE E05 IS INVOKED FOR
THE REFERENCED CONTRACT. PVT SAMPLES SHALL BE INSPECTED, PACKAGED AND
MARKED AS REQUIRED IN THE CONTRACT.
CRITICAL APPLICATION ITEM
TDP Rev B Gen 2 IAW BASIC SPEC NR MIL-DTL-1222J REVISION NR J DTD 12/08/2000 PART PIECE NUMBER: M1222RX10C232NANN
TDP Rev B Gen 2 IAW REFERENCE DRAWING NR 53711 T9074-AS-GIB-010/271 REVISION NR 1 DTD 09/11/2014 PART PIECE NUMBER: M1222RX10C232NANN
TDP Rev B Gen 2 IAW REFERENCE QAP 13873 CDRL-COQC-19071 REVISION NR DTD 03/12/2019 PART PIECE NUMBER:
SPE4A6-26-T-22FT
SECTION B
PR: 7018035951 PRLI: 0001 CONT’D
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 7018035951 0001 EA 123.000
NSN/MATERIAL:5305013722316
DELIVERY (IN DAYS):0171
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: ORIGIN
ACCEPTANCE POINT: ORIGIN
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:33 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:00 CUSH/DUNN MAT:00 CUSH/DUNN THKNESS:0
UNIT CONT:BV OPI:M
INTRMDTE CONT:E5 INTRMDTE CONT QTY:AAA
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:00 -00 No special marking
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
PACKAGING CODE ZZ/EACH FASTENER SHALL HAVE THE ENTIRE LENGTH OF THE SHANK AND THREADS PROTECTED BY A WRAP OR SLEEVE.
IP056: MERCURY OR MERCURY COMPOUNDS ARE PROHIBITED IN PRESERVATION, PACKAGING, PACKING AND MARKING.
PARCEL POST ADDRESS:
W25G1U
W1A8 DLA DISTRIBUTION
DDSP NEW CUMBERLAND FACILITY
2083 NORMANDY DRIVE DOOR 113 TO 134
NEW CUMBERLAND PA 17070-5002
US
FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE
C20 AND CONTRACT
FREIGHT SHIPPING ADDRESS:
W25G1U
W1A8 DLA DISTRIBUTION
DDSP NEW CUMBERLAND FACILITY
2083 NORMANDY DRIVE DOOR 113 TO 134
SPE4A6-26-T-22FT
SECTION B
PR: 7018035951 PRLI: 0001 CONT’D
NEW CUMBERLAND PA 17070-5002
US
Need Ship Date:02/21/2027 Original Required Delivery Date:04/05/2027
SPE4A6-26-T-22FT NSN/Part Number: 5305-01-372-2316 Quantity: 123 EA Purchase Request: 7018035951QTY: 123 Delivery: 171 days ADO