SCREW, CLOSE TOLERAN

SCREW,CLOSE TOLERAN
SCREW, CLOSE TOLERANCE
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
THIS ITEM IS IDENTIFIED AS A COMMERCIAL ITEM (TO INCLUDE 'COMMERCIAL
OF A TYPE')
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN
RD003, COVERED DEFENSE INFORMATION POTENTIALLY APPLIES
THIS ITEM IS DEFINED BY EITHER BY A MILITARY PART STANDARD, OR A PART
STANDARD PUBLISHED BY A CONSENSUS NON-GOVERNMENT STANDARDS ORGANIZATION.
HARDWARE MANUFACTURED TO THE CURRENT REVISION OF THE PART STANDARD
DEFINING THIS ITEM IS ACCEPTABLE.
HARDWARE MANUFACTURED IN THE PAST TO A PREVIOUS, BUT THEN CURRENT,
REVISION OF THE STANDARD IS ACCEPTABLE.
ANY HARDWARE MANUFACTURED FROM THE DATE OF THIS SOLICITATION FORWARD,
SHALL BE MANUFACTURED IN ACCORDANCE WITH THE CURRENT REVISION OF THE
PART STANDARD IN QUESTION.
GAUGING REQUIREMENTS AS FOLLOWS
ALL CLASS 3A AND 3B THREADS WILL BE INSPECTED
FOR DIMENSIONAL CONFORMANCE IN ACCORDANCE WITH
SYSTEM 22 OF FED-STD-H28/20. THIS EXCLUDES
SELF-LOCKING NUTS, INTERNAL THREADS SMALLER
THAN .190 INCH DIA AND EXTERNAL THREADS SMALLER
SPE4A6-26-T-25LB
SECTION B
THAN .138 INCH DIA.
CRITICAL ITEM SOURCE INSPECTION REQUIRED.
RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS
(MANUFACTURERS AND NON-MANUFACTURERS)
Unless otherwise stated, identification marking shall be in accordance with paragraph 4.1.b(2) of MIL-STD-130N. This is in addition to any required manufacturer's logo, lot number, and material identification markings.
RQ017: PHYSICAL IDENTIFICATION/BARE ITEM MARKING
CRITICAL APPLICATION ITEM
TDP Rev E Gen 5 IAW BASIC NON GOVT STD NAS1580 REVISION NR 16 DTD 04/30/2024 PART PIECE NUMBER: STD P/N NAS1580V3T3
TDP Rev E Gen 5 IAW REFERENCE QAP 14153 QAP-EQ001 REVISION NR B DTD 02/13/1996 PART PIECE NUMBER:
TDP Rev E Gen 5 IAW REFERENCE NON GOVT STD NAS621 REVISION NR 14 DTD 05/31/2025 PART PIECE NUMBER:
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 7018134826 0001 EA 25.000
NSN/MATERIAL:5305010590216
DELIVERY (IN DAYS):0005
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: ORIGIN
ACCEPTANCE POINT: ORIGIN
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E
QUP:025 PRES MTHD:10 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:ZZ CUSH/DUNN MAT:00 CUSH/DUNN THKNESS:0
UNIT CONT:A1 OPI:O
INTRMDTE CONT:10 INTRMDTE CONT QTY:AAA
PACK CODE:Q PACKING LEVEL: B
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:00 -00 No special marking
SPE4A6-26-T-25LB
SECTION B
PR: 7018134826 PRLI: 0001 CONT’D
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING
REQUIREMENTS FOR PROCUREMENT
PACKAGING CODE ZZ/EACH FASTENER SHALL HAVE THE
ENTIRE LENGTH OF THE SHANK AND THREADS PROTECTED
BY A WRAP OR SLEEVE.
FREIGHT FORWARDER:
MULTIPLE FORWARDERS EXIST. TRANSPORTATION SEE DLAD PROC NOTE C19. FIRST DESTINATION TRANS SEE DLAD PROC
NOTE C20 AND CONTRACT
FREIGHT SHIPPING ADDRESS:
DKSU00
ROKAF LC CONSOLIDATED SUPPLY DEPOT
403RD MATERIEL MANAGEMENT SQUADRON
PO BOX 384 26 330 1 SIN SUNG RD
SEOSAN SI CHUNGNAM
KR
MARKFOR
DKSU00
ROKAF LC CONSOLIDATED SUPPLY DEPOT
403RD MATERIEL MANAGEMENT SQUADRON
PO BOX 384 26 330 1 SIN SUNG RD
SEOSAN SI CHUNGNAM
KR
M/F: (TCN) DKSU5V53070136
RDD: A01
PROJ: TP 1
SUPP ADD: DA5KDL SIG: L
FOR GOVERNMENT USE ONLY: (IPD) 03
DIC: A31 DIST: N02 ADV: 2L FC: NL
Need Ship Date:00/00/0000 Original Required Delivery Date:11/14/2025
SPE4A6-26-T-25LB NSN/Part Number: 5305-01-059-0216 Quantity: 25 EA Purchase Request: 7018134826QTY: 25 Delivery: 5 days ADO