SCREW, CLOSE TOLERAN

SCREW,CLOSE TOLERAN
SCREW, CLOSE TOLERANCE
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
BOEING CO THE(76301) P/N 3M926-3L9
10EA=1PG
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
RC001: DOCUMENTATION REQUIREMENTS FOR SOURCE APPROVAL REQUEST (SAR)
RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN
RQ002: CONFIGURATION CHANGE MANAGEMENT ENGINEERING CHANGE PROPOSAL
REQUEST FOR VARIANCE (DEVIATION OR WAIVER)
RD003, COVERED DEFENSE INFORMATION POTENTIALLY APPLIES
RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS
(MANUFACTURERS AND NON-MANUFACTURERS)
Casting/forging may be required to manufacture this NSN and tooling is typically involved. The government may not have this special tooling. For sourcing, tooling, materials or other information, please submit a Casting and Forging Assistance Request at either https://www.dla.mil/Aviation/Offers/Engineering/Forging-and-Casting/ or Land & Maritime Supply Chains DSCC.cast.forge@dla.mil. RQ017: PHYSICAL IDENTIFICATION/BARE ITEM MARKING
SPE4A6-26-T-25FZ
SECTION B
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
CRITICAL APPLICATION ITEM
WEST COAST AEROSPACE, INC. 60516 P/N WC4068-3-9
HOWMET GLOBAL FASTENING SYSTEMS INC 1RC86 P/N HT4068-3-9A
SPS Technologies, LLC DBA 80539 P/N HT4068-3-9A HI-SHEAR CORPORATION 73197 P/N HT4068-3-9A SPS TECHNOLOGIES, LLC 56878 P/N HT4068-3-9A SPS TECHNOLOGIES LLC 27624 P/N HT4068-3-9A HUCK INTERNATIONAL, INC 17446 P/N HT4068-3-9A HOWMET GLOBAL FASTENING SYSTEMS INC 06950 P/N HT4068-3-9A SPS TECHNOLOGIES, LLC 06725 P/N HT4068-3-9A HOUSTON PRECISION FASTENERS I LP 1VSL7 P/N 3M926-3L9 HEARTLAND PRECISION FASTENERS INC 0ZC92 P/N 3M926-3L9 TWIST TITE MFG, INC 007R1 P/N 3M926-3L9 THE BOEING COMPANY 76301 P/N 3M926-3L9 FASTENER INNOVATION TECHNOLOGY, INC. 58998 P/N 3M926-3L9 VALLEY-TODECO, INC. 06710 P/N 3M926-3L9 REID PRODUCTS INC. 59563 P/N 11883-3-9/11883-3L9
TDP Rev B Gen 2 IAW REFERENCE DRAWING NR 76301 3M926 REVISION NR P DTD 11/03/2009 PART PIECE NUMBER: P/N 3M926-3L9
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 7018128298 0001 PG 200.000
NSN/MATERIAL:5305011029840
DELIVERY (IN DAYS):0005
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: ORIGIN
ACCEPTANCE POINT: ORIGIN
PREP FOR DELIVERY:
SPE4A6-26-T-25FZ
SECTION B
PR: 7018128298 PRLI: 0001 CONT’D
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:10 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:00 CUSH/DUNN MAT:00 CUSH/DUNN THKNESS:0
UNIT CONT:A1 OPI:O
INTRMDTE CONT:D3 INTRMDTE CONT QTY:AAA
PACK CODE:Q PACKING LEVEL: B
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:00 -00 No special marking
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
FREIGHT FORWARDER:
DIS002
GOI MOD
G&B PACKING COMPANY
1A COLONY ROAD
JERSEY CITY NJ 07305
US
FREIGHT SHIPPING ADDRESS:
DISB00
GOVERNMENT OF ISRAEL
MINISTRY OF DEFENSE
LATZAD METOSIM
IL
MARKFOR
DISB00
GOVERNMENT OF ISRAEL
MINISTRY OF DEFENSE
LATZAD METOSIM
IL
M/F: (TCN) DISB5V41611042
RDD: A01
PROJ: 524 TP 1
SUPP ADD: DA2KEP SIG: L
FOR GOVERNMENT USE ONLY: (IPD) 02
DIC: A31 DIST: N01 ADV: FC: NL
Need Ship Date:00/00/0000 Original Required Delivery Date:06/26/2024
SPE4A6-26-T-25FZ NSN/Part Number: 5305-01-102-9840 Quantity: 200 PG Purchase Request: 7018128298QTY: 200 Delivery: 5 days ADO