SCREW, CLOSE TOLERANCE

SCREW,CLOSE TOLERANCE
SCREW, CLOSE TOLERANCE
SPECIFICATION
NAS1121 THRU 1128, P/N NAS1123-4, THREAD CLASS 3A
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RD003, COVERED DEFENSE INFORMATION POTENTIALLY APPLIES
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS
(MANUFACTURERS AND NON-MANUFACTURERS)
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RQ017: PHYSICAL IDENTIFICATION/BARE ITEM MARKING
RT001: MEASURING AND TEST EQUIPMENT
1 PG = 50 EA
Unless otherwise stated, identification marking shall be in accordance with paragraph 4.1.b(2) of MIL-STD-130N. This is in addition to any required manufacturer's logo, lot number, and material identification markings.
CERTIFICATE OF CONFORMANCE PROCEDURES (FAR 52.246-15) ARE AUTHORIZED,
UNLESS WITHELD BY A QUALITY ASSURANCE LETTER OF INSTRUCTION.
THIS ITEM IS IDENTIFIED AS A COMMERCIAL ITEM (TO INCLUDE 'COMMERCIAL
OF A TYPE')
SAMPLING:
SPE4A6-27-T-024L
SECTION B
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
THIS ITEM IS DEFINED BY EITHER BY A MILITARY PART STANDARD, OR A PART
STANDARD PUBLISHED BY A CONSENSUS NON-GOVERNMENT STANDARDS ORGANIZATION.
HARDWARE MANUFACTURED TO THE CURRENT REVISION OF THE PART STANDARD
DEFINING THIS ITEM IS ACCEPTABLE.
HARDWARE MANUFACTURED IN THE PAST TO A PREVIOUS, BUT THEN CURRENT,
REVISION OF THE STANDARD IS ACCEPTABLE.
ANY HARDWARE MANUFACTURED FROM THE DATE OF THIS SOLICITATION FORWARD,
SHALL BE MANUFACTURED IN ACCORDANCE WITH THE CURRENT REVISION OF THE
PART STANDARD IN QUESTION.
CRITICAL APPLICATION ITEM
TDP Rev D Gen 5 IAW BASIC NON GOVT STD NAS1121 THRU 1128 REVISION NR 15 DTD 10/31/2025 PART PIECE NUMBER: NAS1123-4
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 7019024260 0001 PG 373.000
NSN/MATERIAL:5305009889204
DELIVERY (IN DAYS):0043
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: DESTINATION
ACCEPTANCE POINT: DESTINATION
PREP FOR DELIVERY:
PKGING DATA-QUP:1
WILL BE PACKAGED IN ACCORDANCE WITH ASTM D3951.
All DLA Master List of Technical and Quality Requirements take
SPE4A6-27-T-024L
SECTION B
PR: 7019024260 PRLI: 0001 CONT’D
precedence over ASTM D3951. Mark and label all packaging and packing in accordance with MIL-STD-129. The Unit of Issue (U/I) and Quantity per Unit Pack (QUP) will be as specified in the contract/purchase order. PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
PARCEL POST ADDRESS:
SW3119
DLA DISTRIBUTION WARNER ROBINS
455 BYRON STREET
BLDG 376
ROBINS A F B GA 31098-1887
US
FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE
C20 AND CONTRACT
FREIGHT SHIPPING ADDRESS:
SW3119
DLA DISTRIBUTION WARNER ROBINS
455 BYRON STREET BLDG 376
ROBINS A F B GA 31098-1887
US
Need Ship Date:12/30/2026 Original Required Delivery Date:11/09/2027
SPE4A6-27-T-024L NSN/Part Number: 5305-00-988-9204 Quantity: 373 PG Purchase Request: 7019024260QTY: 373 Delivery: 43 days ADO