SCREW, CLOSE TOLERANCE

SCREW,CLOSE TOLERANCE
SCREW,CLOSE TOLERANCE
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RQ017: PHYSICAL IDENTIFICATION/BARE ITEM MARKING
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
RC001: DOCUMENTATION REQUIREMENTS FOR SOURCE APPROVAL REQUEST (SAR)
RQ002: CONFIGURATION CHANGE MANAGEMENT ENGINEERING CHANGE PROPOSAL
REQUEST FOR VARIANCE (DEVIATION OR WAIVER)
RD003, COVERED DEFENSE INFORMATION POTENTIALLY APPLIES
MIL-STD-130N, 16 Nov 2012 IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY THE DRAWING(S) LISTED BELOW ARE AVAILABLE AT DLA DURING "OPEN SOLICITATION ONLY". TO RECEIVE A COPY OF THE DRAWING(S)<(>,<)> FOR EBS SOLICITATIONS USE URL HTTPS://WWW.DIBBS.BSM.DLA.MIL/RFQ/
QAP EQ003 APPLIES
CRITICAL ITEM SOURCE INSPECTION REQUIRED.
GAUGING REQUIREMENTS AS FOLLOWS
ALL CLASS 3A AND 3B THREADS WILL BE INSPECTED
FOR DIMENSIONAL CONFORMANCE IN ACCORDANCE WITH
SPE4A6-26-T-25ED
SECTION B
SYSTEM 22 OF FED-STD-H28/20. THIS EXCLUDES
SELF-LOCKING NUTS, INTERNAL THREADS SMALLER
THAN .190 INCH DIA AND EXTERNAL THREADS SMALLER
THAN .138 INCH DIA.
73197 Hi–Shear Corp., Torrance, CA 06950 Fairchild Fasteners, City Industry Operations, City of Industry, CA 17446 Huck International Inc., Industrial Division, Carson, CA 80539 SPS Technologies, Inc., Santa Ana, CA 0PTK6 SPS Technologies, Inc., Salt Lake City, UT 58998 Fastener Innovation Technology, Inc., Gardena, CA
CRITICAL APPLICATION ITEM
THE BOEING COMPANY 76301 P/N ST3M430V4-9ASM FASTENER INNOVATION TECHNOLOGY, INC. 58998 P/N ST3M430V4-9ASM HI-SHEAR CORPORATION 73197 P/N HT271A4-9M HI-SHEAR CORPORATION 73197 P/N ST3M430V4-9ASM SPS TECHNOLOGIES LTD, TJ BROOKS K5673 P/N ST3M430V4-9ASM HUCK INTERNATIONAL, INC 17446 P/N ST3M430V4-9ASM HOWMET GLOBAL FASTENING SYSTEMS INC 92215 P/N ST3M430V4-9ASM LISI AEROSPACE CANADA CORP DIV HI L4528 P/N HT271A4-9M HOUSTON PRECISION FASTENERS I LP 1VSL7 P/N ST3M430V4-9ASM SPS Technologies, LLC DBA 80539 P/N 110179-4-9ASM SPS Technologies, LLC DBA 80539 P/N ST3M430V4-9ASM WEST COAST AEROSPACE, INC. 60516 P/N ST3M430V4-9ASM HOWMET GLOBAL FASTENING SYSTEMS INC 06950 P/N HT8137-4-9ASM HOWMET GLOBAL FASTENING SYSTEMS INC 06950 P/N ST3M430V4-9ASM
TDP Rev B Gen 2 IAW REFERENCE DRAWING NR 76301 ST7M251 REVISION NR G DTD 12/12/1996 PART PIECE NUMBER:
TDP Rev B Gen 2 IAW REFERENCE DRAWING NR 98752 200415485 REVISION NR E DTD 01/30/2020 PART PIECE NUMBER:
TDP Rev B Gen 2 IAW REFERENCE DRAWING NR 76301 ST3M430 REVISION NR AA DTD 12/08/2008 PART PIECE NUMBER:
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 7018128095 0001 EA 48.000
NSN/MATERIAL:5305013445533
DELIVERY (IN DAYS):0020
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: ORIGIN
SPE4A6-26-T-25ED
SECTION B
PR: 7018128095 PRLI: 0001 CONT’D
ACCEPTANCE POINT: ORIGIN
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:10 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:00 CUSH/DUNN MAT:00 CUSH/DUNN THKNESS:0
UNIT CONT:10 OPI:O
INTRMDTE CONT:D3 INTRMDTE CONT QTY:AAA
PACK CODE:Q PACKING LEVEL: B
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:00 -00 No special marking
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
FREIGHT FORWARDER:
MULTIPLE FORWARDERS EXIST. TRANSPORTATION SEE DLAD PROC NOTE C19. FIRST DESTINATION TRANS SEE DLAD PROC
NOTE C20 AND CONTRACT
FREIGHT SHIPPING ADDRESS:
DKSH00
ROKAF LC CONSOLIDATED SUPPLY DEPOT
401ST MATERIEL MANAGEMENT SQUADRON
PO BOX 304-130 352 AH-YANG RD
DONG GU DAEGU 41052
KR
MARKFOR
DKSH00
ROKAF LC CONSOLIDATED SUPPLY DEPOT
401ST MATERIEL MANAGEMENT SQUADRON
PO BOX 304-130 352 AH-YANG RD
DONG GU DAEGU 41052
KR
M/F: (TCN) DKSH5V62390313
RDD: A03
PROJ: TP 3
SUPP ADD: DA5KDM SIG: L
FOR GOVERNMENT USE ONLY: (IPD) 12
DIC: A31 DIST: N01 ADV: 2A FC: NL
Need Ship Date:00/00/0000 Original Required Delivery Date:09/03/2026
SPE4A6-26-T-25ED NSN/Part Number: 5305-01-344-5533 Quantity: 48 EA Purchase Request: 7018128095QTY: 48 Delivery: 20 days ADO