This Solicitation opportunity from Department Of Defense was posted on September 1, 2026. The submission period has ended. Browse the details below for market research, or find similar active opportunities.
SCREW, CLOSE TOLERANCE
Contract Overview
Solicitation details, issuing organization, response deadlines, documents, and interested companies for this government contract opportunity.
Active Opportunities Like This One
AI Contract Overview
This solicitation, identified as SPE4A6-26-T-25PG, is issued by the DLA Aviation ASC Commodities Division for the procurement of close tolerance screws, specifically part number NAS1581F3T5 under NSN 5305-01-055-3816. The requirement is for three units to support a Foreign Military Sales requirement for Bulgaria. The contract specifies a delivery timeframe of 20 days after receipt of order, with FOB and inspection/acceptance points set at the origin. The item is classified as a critical application commercial item and must adhere to strict technical and quality standards, including NAS1581 and NAS4002. Quality conformance is governed by RQ006 and RQ001, with sampling conducted per MIL-STD-1916 or ASQ H1331. Specific gauging requirements apply to Class 3A and 3B threads per FED-STD-H28/20. Packaging must comply with MIL-STD-2073-1E and RP001, requiring each fastener to have the entire length of the shank and threads protected by a wrap or sleeve, with marking following MIL-STD-129.
General Info
Place of Performance
BGRSet-Aside
Timeline
Submission Closed
Organization & Contact Information
Full Description
SCREW, CLOSE TOLERANCE
RQ006: QUALITY CONFORMANCE INSPECTION REQUIREMENTS
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS
(MANUFACTURERS AND NON-MANUFACTURERS)
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
Certificate of Quality Compliance (CoQC) Contract Data Requirements Lists (CDRLs), DD Form 1423s, apply to this procurement. Review the Technical Data Package (TDP) for additional information. If CDRL-COQCCDRLs is missing from DLA Technical Data Management Transformation (TDMT) they can also be viewed in the DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
The following Contract Data Requirements Lists (CDRLs), DD Form 1423s, apply to this procurement. Review the Technical Data Package (TDP) for additional information. THIS ITEM IS IDENTIFIED AS A COMMERCIAL ITEM (TO INCLUDE 'COMMERCIAL OF A TYPE')
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
GAUGING REQUIREMENTS AS FOLLOWS
ALL CLASS 3A AND 3B THREADS WILL BE INSPECTED
FOR DIMENSIONAL CONFORMANCE IN ACCORDANCE WITH
SYSTEM 22 OF FED-STD-H28/20. THIS EXCLUDES
SELF-LOCKING NUTS, INTERNAL THREADS SMALLER
THAN .190 INCH DIA AND EXTERNAL THREADS SMALLER
THAN .138 INCH DIA.
SPE4A6-26-T-25PG
SECTION B
RQ017: PHYSICAL IDENTIFICATION/BARE ITEM MARKING
CRITICAL APPLICATION ITEM
TDP Rev F Gen 6 IAW BASIC NON GOVT STD NAS1581 REVISION NR 14 DTD 03/31/2020 PART PIECE NUMBER: NAS1581F3T5
TDP Rev F Gen 6 IAW REFERENCE QAP 13873 CDRLCOQC26124 REVISION NR DTD 12/04/2025 PART PIECE NUMBER:
TDP Rev F Gen 6 IAW REFERENCE NON GOVT STD NAS4002 REVISION NR 12 DTD 07/31/2020 PART PIECE NUMBER:
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 7018147705 0001 HD 3.000
NSN/MATERIAL:5305010553816
DELIVERY (IN DAYS):0020
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: ORIGIN
ACCEPTANCE POINT: ORIGIN
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:10 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:ZZ CUSH/DUNN MAT:00 CUSH/DUNN THKNESS:0
UNIT CONT:D3 OPI:O
INTRMDTE CONT:D3 INTRMDTE CONT QTY:AAA
PACK CODE:Q PACKING LEVEL: B
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:00 -00 No special marking
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
PACKAGING CODE ZZ/EACH FASTENER SHALL HAVE THE ENTIRE LENGTH OF THE SHANK AND THREADS PROTECTED BY A WRAP OR SLEEVE.
FREIGHT FORWARDER:
SPE4A6-26-T-25PG
SECTION B
PR: 7018147705 PRLI: 0001 CONT’D
DBU002
DANIEL F YOUNG INC (DF YOUNG)
176-20 147TH AVENUE
1500 EAST 2ND STREET BUILDING 2
EDDYSTONE PA 19022
US
FREIGHT SHIPPING ADDRESS:
DBUE00
MILITARY UNIT 28000
POC MOD ARMAMENTS POLICY DIR
TEL 0035929220866 contact@example.gov
GRAF IGNATIEVO
BG
MARKFOR
DBUE00
MILITARY UNIT 28000
POC MOD ARMAMENTS POLICY DIR
TEL 0035929220866 contact@example.gov
GRAF IGNATIEVO
BG
M/F: (TCN) DBUE5453245180
RDD: A01
PROJ: TP 2
SUPP ADD: DA2SAB SIG: L
FOR GOVERNMENT USE ONLY: (IPD) 08
DIC: A31 DIST: N56 ADV: 2L FC: NL
Need Ship Date:00/00/0000 Original Required Delivery Date:11/25/2025
SPE4A6-26-T-25PG NSN/Part Number: 5305-01-055-3816 Quantity: 3 HD Purchase Request: 7018147705QTY: 3 Delivery: 20 days ADO
More opportunities from Department Of Defense → ASC COMMODITIES DIVISION
Same awarding agency
Earlier notices in this NAICS code
Posted before this notice, open and closed
Find Active Opportunities Like This
Get AI-powered intelligence on the opportunities still open
Every page of the solicitation package shredded into a compliance breakdown
AI-powered matching based on your capabilities and past performance
Competitor and incumbent history on the requirement
Automated alerts on amendments, Q&A deadlines, and award
Join 750+ contractors already using CLEATUS