This Solicitation opportunity from Department Of Defense was posted on July 14, 2026. The submission period has ended. Browse the details below for market research, or find similar active opportunities.
SCREW, CLOSE TOLERANCE
Contract Overview
Solicitation details, issuing organization, response deadlines, documents, and interested companies for this government contract opportunity.
Active Opportunities Like This One
AI Contract Overview
The contract is for the procurement of 43 close-tolerance screws under NSN 5305-01-356-8977, issued by the ASC Commodities Division of the Department of Defense through solicitation SPE4A6-26-T-06NG. The items must adhere to stringent technical and quality requirements drawn from the DLA Master List of Technical and Quality Requirements, with packaging and labeling governed by RP001, MIL-STD-129, and ASTM D3951, unless superseded by DLA standards. Surface marking is mandatory for all screws except those with a thread diameter of 0.190 inches or smaller, requiring the manufacturer’s symbol to be directly applied in accordance with MIL-HDBK-57, with no markings allowed on bearing surfaces. Sampling and inspection must follow MIL-STD-1916 or an equivalent zero-based plan, with critical, major, and minor attributes assigned verification levels of VII, IV, and II respectively, or AQLs of 0.1, 1.0, and 4.0, and acceptance requires zero non-conformances unless otherwise stated. The contract incorporates numerous FAR and DFARS clauses governing equal opportunity, trafficking in persons, employment verification, hazardous material identification, cybersecurity through NIST SP 800-171, transportation by sea, whistleblower rights, and disclosure of information, with specific emphasis on safety data sheet submission and hazard communication compliance. Delivery is required to the DLA Distribution facility in New Cumberland, PA, 171 days after award, with FOB origin terms and invoicing performed exclusively through WAWF. The contract type is defined under FAR 52.216-1 Alternate I with an authorized deviation, and while no pricing is filled in, the solicitation is structured for competitive award, with evaluation likely based on lowest price technically acceptable criteria. Offerors must possess a valid UEI and CAGE code, and must represent their small business status and socioeconomic certifications, with additional disclosures required for covered defense telecommunications or joint ventures. All supplies must comply with DLA’s covered defense information requirements under RD002, and the contract prohibits the use of unauthorized obligations as stipulated in FAR 52.32-39.
General Info
Agency
NAICS
Place of Performance
2083 NORMANDY DRIVE DOOR 113 TO 134, NEW CUMBERLAND, PA, 17070-5002, USASet-Aside
Timeline
Submission Closed
Organization & Contact Information
Full Description
SCREW,CLOSE TOLERANCE
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RD002, COVERED DEFENSE INFORMATION APPLIES
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
RQ017: PHYSICAL INDENTIFICATION/BARE ITEM MARKING
ITEM SURFACE MARKING REQUIREMENT: IN ADDITION TO MARKING REQUIREMENTS
DEFINED BY TECHNICAL DATA, THE MANUFACTURER'S SYMBOL IS REQUIRED AND
SHALL BE APPLIED DIRECTLY TO THE SURFACE OF THIS ITEM. THE
MANUFACTURER'S SYMBOL MUST BE LISTED IN MIL-HDBK-57. DO NOT PLACE ANY
MARKINGS ON BEARING SURFACES. MANUFACTURER'S SYMBOL IS NOT REQUIRED ON
FASTENERS WITH A THREAD DIAMETER OF 0.190 INCHES AND SMALLER.
FOR MANUFACTURER'S SYMBOL REGISTRATION INFORMATION AND INQUIRIES PLEASE
VISIT THE MIL-HDBK-57 URL AT:
http://www.dla.mil/TroopSupport/IndustrialHardware/Engineering-and-Techn http://www.dla.mil/TroopSupport/IndustrialHardware/Engineering-and-Techn ical-services/logoreg/
THIS NSN IS PROCURED AS FULLY COMPETITIVE IN ACCORDANCE WITH A MILITARY / FEDERAL SPECIFICATION/STANDARD. SEE NSN/Part Number: 5305-01-356-8977 Quantity: 43 EA Purchase Request: 7017487252QTY: 43 Delivery: 171 days ADO
More opportunities from Department Of Defense → ASC COMMODITIES DIVISION
Same awarding agency
Find Active Opportunities Like This
Get AI-powered intelligence on the opportunities still open
Every page of the solicitation package shredded into a compliance breakdown
AI-powered matching based on your capabilities and past performance
Competitor and incumbent history on the requirement
Automated alerts on amendments, Q&A deadlines, and award
Join 650+ contractors already using CLEATUS