SCREW, MACHINE

SCREW,MACHINE
SCREW, MACHINE
RQ017: PHYSICAL INDENTIFICATION/BARE ITEM MARKING
NO ASBESTOS AS DEFINED IN FED-STD-313 IS
PERMITTED IN THIS ITEM
SPECIFICATION
FF-S-92D, MS51957, P/N MS51957-59, THREAD CLASS 2A
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RD003, COVERED DEFENSE INFORMATION POTENTIALLY APPLIES
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RT001: MEASURING AND TEST EQUIPMENT
MERCURY OR MERCURY CONTAINING COMPOUNDS SHALL
NOT BE INTENTIONALLY ADDED TO<(>,<)> OR COME IN DIRECT
CONTACT WITH<(>,<)> ANY HARDWARE OR SUPPLIES FURNISHED
UNDER THIS CONTRACT. EXCEPTION: FUNCTIONAL MERCURY
USED IN BATTERIES, FLUORESCENT LIGHTS, REQUIRED
INSTRUMENTS; SENSORS OR CONTROLS; WEAPON SYSTEMS;
AND CHEMICAL ANALYSIS REAGENTS SPECIFIED BY NAVSEA.
PORTABLE FLUORESCENT LAMPS AND PORTABLE INSTRUMENTS
CONTAINING MERCURY SHALL BE SHOCK PROOF AND CONTAIN
A SECOND BOUNDARY OF CONTAINMENT OF THE MERCURY OR
MERCURY COMPOUND. (IAW NAVSEA 5100-003D).
ITEM SURFACE MARKING REQUIREMENT: MATERIAL SYMBOL, MANUFACTURER'S SYMBOL
AND LOT NUMBER ARE REQUIRED AND SHALL BE APPLIED DIRECTLY TO THE SURFACE
OF THIS ITEM IN ACCORDANCE WITH MIL-DTL-1222. MATERIAL SYMBOL SHALL BE
SPE4A6-26-T-817X
SECTION B
IN ACCORDANCE WITH THE "ADDITIONAL REQUIREMENTS" COLUMN OF MIL-DTL-1222
TABLE I. LOCATION OF MARKINGS SHALL IN ACCORDANCE WITH MIL-DTL-1222J
PARA. 3.13.2.
THE MANUFACTURER'S SYMBOL (LOGO) MUST BE LISTED IN MIL-HDBK-57. FOR
FASTENERS LESS THAN 1/2 INCH DIAMETER, IF ALL REQUIRED MARKINGS CANNOT
BE APPLIED DUE TO SPACE LIMITATIONS, THE MARKINGS SHALL BE APPLIED IN
THE FOLLOWING ORDER OF PRECEDENCE: MATERIAL SYMBOL, MANUFACTURER'S
SYMBOL AND LOT NUMBER. MARKINGS NOT INCLUDED ON THE BARE ITEM SHALL BE
PLACED ON PACKAGING LABELS.
FOR MANUFACTURER'S SYMBOL INFORMATION AND INQUIRIES PLEASE VISIT THE
MIL-HDBK-57 URL AT:
https://www.troopsupport.dla.mil/Hardware/Technical/logoreg.asp
THIS ITEM IS IDENTIFIED AS A COMMERCIAL ITEM (TO INCLUDE 'COMMERCIAL
OF A TYPE')
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
Unless otherwise stated, identification marking shall be in accordance with paragraph 4.1.b(2) of MIL-STD-130N. This is in addition to any required manufacturer's logo, lot number, and material identification markings.
RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS
(MANUFACTURERS AND NON-MANUFACTURERS)
CRITICAL APPLICATION ITEM
IAW BASIC SPEC NR MS51957G
REVISION NR G DTD 04/14/2025
PART PIECE NUMBER: MS51957-59
IAW REFERENCE SPEC NR MIL-DTL-1222J
REVISION NR J DTD 12/08/2000
PART PIECE NUMBER:
IAW REFERENCE UNK FF-S-92E(1)
REVISION NR 1 DTD 05/05/2025
PART PIECE NUMBER:
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
SPE4A6-26-T-817X
SECTION B
PR: 7015603583 PRLI: 0001 CONT’D
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 7015603583 0001 EA 405.000
NSN/MATERIAL:5305000509225
DELIVERY (IN DAYS):0166
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: ORIGIN
ACCEPTANCE POINT: ORIGIN
PREP FOR DELIVERY:
PKGING DATA-QUP:001
WILL BE PACKAGED IN ACCORDANCE WITH ASTM D3951.
All DLA Master List of Technical and Quality Requirements take precedence over ASTM D3951. Mark and label all packaging and packing in accordance with MIL-STD-129. The Unit of Issue (U/I) and Quantity per Unit Pack (QUP) will be as specified in the contract/purchase order. PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
PARCEL POST ADDRESS:
SW3211
DLA DISTRIBUTION DEPOT OKLAHOMA
3301 F AVE CEN REC BLDG 506 DR 22
TINKER AFB OK 73145-8000
US
FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE
C20 AND CONTRACT
FREIGHT SHIPPING ADDRESS:
SW3211
DLA DISTRIBUTION DEPOT OKLAHOMA
3301 F AVE CEN REC BLDG 506 DR 22
TINKER AFB OK 73145-8000
US
Need Ship Date:08/18/2026 Original Required Delivery Date:09/11/2026
SPE4A6-26-T-817X NSN/Part Number: 5305-00-050-9225 Quantity: 405 EA Purchase Request: 7015603583QTY: 405 Delivery: 166 days ADO