This Solicitation opportunity from Department Of Defense was posted on April 30, 2026. The submission period has ended. Browse the details below for market research, or find similar active opportunities.
SCREW, MACHINE
Contract Overview
Solicitation details, issuing organization, response deadlines, documents, and interested companies for this government contract opportunity.
Active Opportunities Like This One
AI Contract Overview
This contract covers the procurement of machine screws specified by part number NAS605-32P, conforming to NAS600 through NAS606 standards with thread class 3A. The screws must meet all applicable technical and quality requirements as outlined in the Defense Logistics Agency (DLA) Master List of Technical and Quality Requirements, with identification and marking complying with MIL-STD-130N and MIL-STD-129 standards. Quality assurance provisions include adherence to tailored higher-level contract quality requirements, packaging per MIL-STD-2073-1E, and sampling methods aligned with MIL-STD-1916 or equivalents. The hardware must be manufactured to the current or previously valid revision of the applicable military or consensus standards, with a certificate of conformance authorized unless specific quality assurance instructions dictate otherwise. The contract specifies a quantity of four units, to be delivered within 20 days, with delivery and inspection points set at the destination. The contract demands strict compliance with packaging and preservation requirements to ensure the screws arrive in suitable condition. The purchase is managed by the ASC Commodities Division of the Department of Defense, with shipment directed to the Logistics Readiness Center in Kadena Air Base, Okinawa, Japan. Communication for the contract is primarily handled through the point of contact listed, and the contract documentation includes detailed instructions for lot inspection, identification marking, and acceptance criteria, ensuring adherence to rigorous defense standards.
General Info
Agency
NAICS
Place of Performance
UNIT 5136 BOX 10, APO, AP, 96368-5136, USSet-Aside
Documents
(1)AI Contract Breakdown
Uniform Contract FormatWhat is UCF?
Uniform Contract Format (UCF) uses AI to break down any contract into standardized sections—scope, pricing, deliverables, and evaluation criteria.
Timeline
Submission Closed
Organization & Contact Information
Full Description
SCREW, MACHINE
SPECIFICATION
NAS600 THRU 606, P/N NAS605-32P, THREAD CLASS 3A
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RD003, COVERED DEFENSE INFORMATION POTENTIALLY APPLIES
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS
(MANUFACTURERS AND NON-MANUFACTURERS)
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RQ017: PHYSICAL INDENTIFICATION/BARE ITEM MARKING
RT001: MEASURING AND TEST EQUIPMENT
Unless otherwise stated, identification marking shall be in accordance with paragraph 4.1.b(2) of MIL-STD-130N. This is in addition to any required manufacturer's logo, lot number, and material identification markings.
CERTIFICATE OF CONFORMANCE PROCEDURES (FAR 52.246-15) ARE AUTHORIZED,
UNLESS WITHELD BY A QUALITY ASSURANCE LETTER OF INSTRUCTION.
THIS ITEM IS IDENTIFIED AS A COMMERCIAL ITEM (TO INCLUDE 'COMMERCIAL
OF A TYPE')
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPE4A6-26-T-39R1
SECTION B
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
THIS ITEM IS DEFINED BY EITHER BY A MILITARY PART STANDARD, OR A PART
STANDARD PUBLISHED BY A CONSENSUS NON-GOVERNMENT STANDARDS ORGANIZATION.
HARDWARE MANUFACTURED TO THE CURRENT REVISION OF THE PART STANDARD
DEFINING THIS ITEM IS ACCEPTABLE.
HARDWARE MANUFACTURED IN THE PAST TO A PREVIOUS, BUT THEN CURRENT,
REVISION OF THE STANDARD IS ACCEPTABLE.
ANY HARDWARE MANUFACTURED FROM THE DATE OF THIS SOLICITATION FORWARD,
SHALL BE MANUFACTURED IN ACCORDANCE WITH THE CURRENT REVISION OF THE
PART STANDARD IN QUESTION.
IAW BASIC NON GOVT STD NAS600 THRU 606
REVISION NR 11 DTD 10/31/2018
PART PIECE NUMBER: STD P/N NAS605-32P
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 7016529288 0001 EA 4.000
NSN/MATERIAL:5305012545402
DELIVERY (IN DAYS):0020
DELIVER FOB: DESTINATION
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: DESTINATION
ACCEPTANCE POINT: DESTINATION
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:10 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:00 CUSH/DUNN MAT:00 CUSH/DUNN THKNESS:0
UNIT CONT:D3 OPI:O
INTRMDTE CONT:D3 INTRMDTE CONT QTY:AAA
PACK CODE:Q PACKING LEVEL: B
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:00 -00 No special marking
SPE4A6-26-T-39R1
SECTION B
PR: 7016529288 PRLI: 0001 CONT’D
PARCEL POST ADDRESS:
FB5270
FB5270 18 LRS LGRDDC
UNIT 5136 BOX 10
APO AP 96368-5136
US
RDD 777 SHIPMENT. TRANSPORTATION SEE DLAD PROC NOTE C19. FIRST DESTINATION TRANSPORTATION SEE DLAD PROC
NOTE C20 AND CONTRACT
FREIGHT SHIPPING ADDRESS:
FB5270
FB5270 18 LRS LGRDDC
CP 011 81 98 938 1111 EXT 634 7155
KADENA AB BLDG 794 DOUGLAS BLVD
KADENA AB OKINAWA 904 0200
JP
M/F: (TCN) FB527061110015
RDD: 777
PROJ: TP 2
SUPP ADD: YBQ353 SIG: A
FOR GOVERNMENT USE ONLY: (IPD) 04
DIC: A01 DIST: 01 ADV: 2D FC: 6C
Need Ship Date:00/00/0000 Original Required Delivery Date:04/24/2026
SPE4A6-26-T-39R1 NSN/Part Number: 5305-01-254-5402 Quantity: 4 EA Purchase Request: 7016529288QTY: 4 Delivery: 20 days ADO