This Solicitation opportunity from Department Of Defense was posted on May 13, 2026. The submission period has ended. Browse the details below for market research, or find similar active opportunities.
SCREW, MACHINE
Contract Overview
Solicitation details, issuing organization, response deadlines, documents, and interested companies for this government contract opportunity.
Active Opportunities Like This One
AI Contract Overview
The contract solicits eight machine screws defined by NSN 5305-00-051-2331, to be delivered within five days of order placement to Tobyhanna, Pennsylvania, under a simplified acquisition process governed by FAR 52.213-4. The item must comply with current revisions of applicable military or consensus industry standards, with prior revisions acceptable only if they were current at the time of manufacture. Technical and quality requirements are dictated by the DLA Master List of Technical and Quality Requirements referenced under RA001, which supersedes other specifications. Packaging and marking must conform to RP001, MIL-STD-129 for shipment labeling, and MIL-STD-130N for item identification, including mandatory Data Matrix barcodes and government item identification, in addition to manufacturer logos, lot numbers, and material markings. Sampling for quality acceptance follows MIL-STD-1916 or ASQ H1331 Table 1, with zero non-conformances required unless otherwise specified, and attributes are to be classified with V7, V4, and V2 verification levels or corresponding AQLs. Hazardous materials must be labeled per 29 CFR 1910.1200 and MIL-STD-129, while radioactive materials exceeding thresholds require additional labeling per MIL-STD-129. The contract mandates use of WAWF for invoicing and receiving reports, with payment processed via DoDAACs. Cybersecurity compliance is enforced through DFARS clauses requiring safeguarding of covered defense information, NIST SP 800-171 assessments, and incident reporting. Offerors must possess active UEI and CAGE codes and certify their small business status if claiming socioeconomic advantages. The contract prohibits acquisition of covered telecommunications equipment and requires compliance with trafficking in persons and employment eligibility verification regulations. Place of performance is fixed at Tobyhanna, PA, with FOB destination terms applying. No option periods, key personnel requirements, or OCI provisions are specified. Proposals must be submitted electronically via DIBBS by May 21, 2026, adhering to DLA’s automated simplified acquisition format.
General Info
Agency
Contract Value
$220.8NAICS
Place of Performance
ASARS 1C BAY 6, TOBYHANNA, PA, 18466-5050, USASet-Aside
Awardee
Award Issued Date
Timeline
Submission Closed
Organization & Contact Information
Full Description
SCREW, MACHINE
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RQ017: PHYSICAL INDENTIFICATION/BARE ITEM MARKING
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
Unless otherwise stated, identification marking shall be in accordance with paragraph 4.1.b(2) of MIL-STD-130N. This is in addition to any required manufacturer's logo, lot number, and material identification markings.
THIS ITEM IS DEFINED BY EITHER BY A MILITARY PART STANDARD, OR A PART
STANDARD PUBLISHED BY A CONSENSUS NON-GOVERNMENT STANDARDS ORGANIZATION.
HARDWARE MANUFACTURED TO THE CURRENT REVISION OF THE PART STANDARD
DEFINING THIS ITEM IS ACCEPTABLE.
HARDWARE MANUFACTURED IN THE PAST TO A PREVIOUS, BUT THEN CURRENT,
REVISION OF THE STANDARD IS ACCEPTABLE.
ANY HARDWARE MANUFACTURED FROM THE DATE OF THIS SOLICITATION FORWARD,
SHALL BE MANUFACTURED IN ACCORDANCE WITH THE CURRENT REVISION OF THE
PART STANDARD IN QUESTION.
THIS NSN IS PROCURED AS FULLY COMPETITIVE IN
ACCORDANCE WITH A MILITARY / FEDERAL
SPECIFICATION/STANDARD. SEE NSN/Part Number: 5305-00-051-2331 Quantity: 8 EA Purchase Request: 7016414958QTY: 8 Delivery: 5 days ADO
More opportunities from Department Of Defense → ASC COMMODITIES DIVISION
Same awarding agency
Find Active Opportunities Like This
Get AI-powered intelligence on the opportunities still open
Every page of the solicitation package shredded into a compliance breakdown
AI-powered matching based on your capabilities and past performance
Competitor and incumbent history on the requirement
Automated alerts on amendments, Q&A deadlines, and award
Join 650+ contractors already using CLEATUS