This Solicitation opportunity from Department Of Defense was posted on July 21, 2026. The submission period has ended. Browse the details below for market research, or find similar active opportunities.
SCREW, MACHINE
Contract Overview
Solicitation details, issuing organization, response deadlines, documents, and interested companies for this government contract opportunity.
Active Opportunities Like This One
AI Contract Overview
The contract specifies the procurement of 40 machine screws identified by NSN 5305008801424 and part number MS35273-33, manufactured in strict compliance with the current revision of the non-government standard NASM35273 Revision 2 dated 01/31/2019, or an equivalent military part standard. All hardware must adhere to the DLA Master List of Technical and Quality Requirements, which supersedes any referenced standards such as ASTM D3951 or MIL-STD-130N, with marking required under paragraph 4.1.b(2) of MIL-STD-130N including manufacturer logo, lot number, and material identification, in addition to permanent part identification. Sampling for acceptance must follow MIL-STD-1916 or ASQ H1331 Table 1 with zero non-conformances permitted in the sample lot unless otherwise stated, and unspecified attributes are treated as major with verification levels VII, IV, and II assigned to critical, major, and minor characteristics respectively. The item is classified as a critical application item, and all manufacturing must use current revisions of applicable standards, with past revisions only acceptable for previously produced hardware. Packaging must conform to ASTM D3951 unless a more restrictive requirement exists in the DLA Master List, with palletization following RP001 and labeling required per MIL-STD-129 including barcoding and data matrix symbols. Delivery is FOB origin with inspection and acceptance occurring at the manufacturer’s facility, and shipment must be completed within 168 days of award, with the original required delivery date set for March 1, 2027. The contract employs a Lowest Price Technically Acceptable (LPTA) evaluation method, where technical compliance is a mandatory threshold and award goes to the lowest priced qualified offer, with a HUBZone price preference applied. The offeror must comply with extensive regulatory clauses related to hazardous materials, including submission of Safety Data Sheets per OSHA 29 CFR 1910.1200, prohibition of hexavalent chromium, and adherence to the Combatting Trafficking in Persons and Employment Eligibility Verification requirements. Shipping must be conducted on U.S.-flag vessels if transported by sea, with mandatory notification to MARAD and submission of ocean bills of lading. The contract includes mandatory flow-down clauses to subcontractors for hazardous materials,
General Info
Agency
NAICS
Place of Performance
PHANTOM RD BLDG 147 BAY A, CHERRY POINT, NC, 28533-5040, USASet-Aside
Timeline
Submission Closed
Organization & Contact Information
Full Description
SCREW, MACHINE
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RQ017: PHYSICAL INDENTIFICATION/BARE ITEM MARKING
RQ001: TAILORED HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS
(MANUFACTURERS AND NON-MANUFACTURERS)
Unless otherwise stated, identification marking shall be in accordance with paragraph 4.1.b(2) of MIL-STD-130N. This is in addition to any required manufacturer's logo, lot number, and material identification markings.
THIS ITEM IS DEFINED BY EITHER BY A MILITARY PART STANDARD, OR A PART
STANDARD PUBLISHED BY A CONSENSUS NON-GOVERNMENT STANDARDS ORGANIZATION.
HARDWARE MANUFACTURED TO THE CURRENT REVISION OF THE PART STANDARD
DEFINING THIS ITEM IS ACCEPTABLE.
HARDWARE MANUFACTURED IN THE PAST TO A PREVIOUS, BUT THEN CURRENT,
REVISION OF THE STANDARD IS ACCEPTABLE.
ANY HARDWARE MANUFACTURED FROM THE DATE OF THIS SOLICITATION FORWARD,
SHALL BE MANUFACTURED IN ACCORDANCE WITH THE CURRENT REVISION OF THE
PART STANDARD IN QUESTION.
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
SPE4A6-26-T-08XB
SECTION B
CRITICAL APPLICATION ITEM
TDP Rev A Gen 1 IAW BASIC NON GOVT STD NASM35273 REVISION NR 2 DTD 01/31/2019 PART PIECE NUMBER: P/N MS35273-33
TDP Rev A Gen 1 IAW REFERENCE UNK FF-S-92E(1) REVISION NR E DTD 05/05/2025 PART PIECE NUMBER:
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 7017572426 0001 EA 40.000
NSN/MATERIAL:5305008801424
DELIVERY (IN DAYS):0168
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: ORIGIN
ACCEPTANCE POINT: ORIGIN
PREP FOR DELIVERY:
PKGING DATA-QUP:001
WILL BE PACKAGED IN ACCORDANCE WITH ASTM D3951.
All DLA Master List of Technical and Quality Requirements take precedence over ASTM D3951. Mark and label all packaging and packing in accordance with MIL-STD-129. The Unit of Issue (U/I) and Quantity per Unit Pack (QUP) will be as specified in the contract/purchase order. PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
PARCEL POST ADDRESS:
SW3113
DLA DISTRIBUTION CHERRY POINT
PHANTOM RD BLDG 147 BAY A
CHERRY POINT NC 28533-5040
US
FOR TRANSPORTATION SEE DLAD DLAD PROC NOTE C19. FOR FIRST DESTINATION TRANSPORTATION SEE DLAD PROC NOTE
C20 AND CONTRACT
FREIGHT SHIPPING ADDRESS:
SPE4A6-26-T-08XB
SECTION B
PR: 7017572426 PRLI: 0001 CONT’D
SW3113
DLA DISTRIBUTION CHERRY POINT
PHANTOM RD BLDG 147 BAY A
CHERRY POINT NC 28533-5040
US
Need Ship Date:01/14/2027 Original Required Delivery Date:03/01/2027
SPE4A6-26-T-08XB NSN/Part Number: 5305-00-880-1424 Quantity: 40 EA Purchase Request: 7017572426QTY: 40 Delivery: 168 days ADO
More opportunities from Department Of Defense → ASC COMMODITIES DIVISION
Same awarding agency
Find Active Opportunities Like This
Get AI-powered intelligence on the opportunities still open
Every page of the solicitation package shredded into a compliance breakdown
AI-powered matching based on your capabilities and past performance
Competitor and incumbent history on the requirement
Automated alerts on amendments, Q&A deadlines, and award
Join 650+ contractors already using CLEATUS