SCREW, SHOULDER

SCREW,SHOULDER
SCREW, SHOULDER
THIS IS A SOURCE CONTROLLED ITEM WHICH MUST BE
MANUFACTURED AND TESTED IN ACCORDANCE WITH THE
CITED LIMITED RIGHTS DATA. THE GOVERNMENT CAN
NOT PROVIDE THE DATA. ONLY THOSE VENDORS WHO
HAVE ACCESS TO THE DATA OR CAN PROVIDE TRACE
ABILITY TO THE APPROVED SOURCES SHOULD QUOTE.
SAR PACKAGE IS REQUIRED IF YOUR COMPANY IS
CONSIDERING SOURCE APPROVAL.
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RQ006: QUALITY CONFORMANCE INSPECTION REQUIREMENTS
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RQ017: PHYSICAL IDENTIFICATION/BARE ITEM MARKING
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
Certificate of Quality Compliance (CoQC) Contract Data Requirements Lists (CDRLs), DD Form 1423s, apply to this procurement. Review the Technical Data Package (TDP) for additional information. If CDRL-COQCCDRLs is missing from DLA Technical Data Management Transformation (TDMT) they can also be viewed in the DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
52.246-15 CERTIFICATE OF CONFORMANCE
MIL-STD-130N, 16 Nov 2012
SPE4A0-26-T-4542
SECTION B
IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY
ITEM SURFACE MARKING REQUIREMENT: IN ADDITION TO MARKING REQUIREMENTS
DEFINED BY TECHNICAL DATA, THE MANUFACTURER'S SYMBOL IS REQUIRED AND
SHALL BE APPLIED DIRECTLY TO THE SURFACE OF THIS ITEM. THE
MANUFACTURER'S SYMBOL MUST BE LISTED IN MIL-HDBK-57. DO NOT PLACE ANY
MARKINGS ON BEARING SURFACES. MANUFACTURER'S SYMBOL IS NOT REQUIRED ON
FASTENERS WITH A THREAD DIAMETER OF 0.190 INCHES AND SMALLER.
FOR MANUFACTURER'S SYMBOL REGISTRATION INFORMATION AND INQUIRIES PLEASE
VISIT THE MIL-HDBK-57 URL AT:
http://www.dla.mil/TroopSupport/IndustrialHardware/Engineering-and-Techn http://www.dla.mil/TroopSupport/IndustrialHardware/Engineering-and-Techn ical-services/logoreg/
THE DRAWING(S) LISTED BELOW ARE AVAILABLE AT DLA DURING "OPEN SOLICITATION ONLY". TO RECEIVE A COPY OF THE DRAWING(S)<(>,<)> FOR EBS SOLICITATIONS USE URL HTTPS://WWW.DIBBS.BSM.DLA.MIL/RFQ/
RD002, COVERED DEFENSE INFORMATION APPLIES
CERTIFICATE OF CONFORMANCE PROCEDURES (FAR 52.246-15) ARE AUTHORIZED,
UNLESS WITHELD BY A QUALITY ASSURANCE LETTER OF INSTRUCTION.
FAR 52.246-11, HIGHER LEVEL CONTRACT QUALITY
REQUIREMENTS, APPLIES/ISO 9001/ANSI/ASQC
Q 9001 APPLIES.
THE ORIGIN INSPECTION REQUIREMENT HAS BEEN
REEVALUATED AND CHANGED TO DESTINATION
MIL-STD-1916
AM GENERAL LLC
CAGE Code 34623,, P/N 6050285
GENERAL FASTENERS COMPANY Cage 3M915 Part SLDR652TZ
AM GENERAL LLC 34623 P/N 6050285
TDP Rev A Gen 2 IAW BASIC DRAWING NR 1X4F3 AMSCBDOC REVISION NR DTD 03/07/2007 PART PIECE NUMBER: 6050285
DLA issues this document using the DoD authorized unit of issue, please refer to the following URL to determine the corresponding ANSI X12 unit of issue.
https://view.officeapps.live.com/op/view.aspx?src=https%3A%2F%2Fwww.dla.mil%2FPortals%2F104%2FDocuments% 2FDLMS%2FeApplications%2FLogDataAdmin%2FUnitofIssueandPurchaseUnit.xlsx&wdOrigin=BROWSELINK
CLIN PR PRLI UI QUANTITY UNIT PRICE TOTAL PRICE.
0001 7017240363 0001 EA 4.000
NSN/MATERIAL:5305016999433
SPE4A0-26-T-4542
SECTION B
PR: 7017240363 PRLI: 0001 CONT’D
DELIVERY (IN DAYS):0005
DELIVER FOB: ORIGIN
QTY VARIANCE: PLUS 0% MINUS 0%
INSPECTION POINT: DESTINATION
ACCEPTANCE POINT: DESTINATION
PREP FOR DELIVERY:
PKGING DATA MIL-STD-2073-1E
QUP:001 PRES MTHD:31 CLNG/DRY:1 PRESV MAT:00
WRAP MAT:00 CUSH/DUNN MAT:00 CUSH/DUNN THKNESS:0
UNIT CONT:BL OPI:M
INTRMDTE CONT:ED INTRMDTE CONT QTY:100
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.
SPECIAL MARKING CODE:00 -00 No special marking
PALLETIZATION SHALL BE IN ACCORDANCE WITH RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
BULK BREAK POINT:
W5CKTB
W8T8 WI ARNG FMS 8
952 UNIVERSAL BLVD
WHITEWATER WI 53190-1464
US
RDD(3-POS RDD)/NMCS SHIPMENT. SHIP BY FASTAST TRACEABLE MEANS. DO NOT USE PARCEL POST.
FREIGHT SHIPPING ADDRESS:
W90P82
W8T8 WI ARNG FMS 8
952 UNIVERSAL BLVD
FMS 8
WHITEWATER WI 53190-0000
US
MARKFOR
W90P82
W8T8 WI ARNG FMS 8
952 UNIVERSAL BLVD
FMS 8
WHITEWATER WI 53190-0000
US
M/F: (TCN) W90P8261660008
RDD: N
PROJ: 07Q TP 1
SUPP ADD: W5CK4Y SIG: A
FOR GOVERNMENT USE ONLY: (IPD) 03
DIC: A3A DIST: ADV: 2A FC: 62
SPE4A0-26-T-4542
SECTION B
PR: 7017240363 PRLI: 0001 CONT’D
Need Ship Date:00/00/0000 Original Required Delivery Date:06/18/2026
SPE4A0-26-T-4542 NSN/Part Number: 5305-01-699-9433 Quantity: 4 EA Purchase Request: 7017240363QTY: 4 Delivery: 5 days ADO